[PATCH net-next 00/15] MT7530 DSA subdriver improvements

Arınç ÜNAL arinc.unal at arinc9.com
Sat Nov 18 04:31:50 PST 2023


Hello!

This patch series simplifies the MT7530 DSA subdriver and improves the
logic of the support for MT7530, MT7531, and the switch on the MT7988 SoC.

I have done a simple ping test to confirm basic communication on all switch
ports on the MCM and standalone MT7530 and MT7531 switch with this patch
series applied.

MT7621 Unielec, MCM MT7530:

rgmii-only-gmac0-mt7621-unielec-u7621-06-16m.dtb
gmac0-and-gmac1-mt7621-unielec-u7621-06-16m.dtb

tftpboot 0x80008000 mips-uzImage.bin; tftpboot 0x83000000 mips-rootfs.cpio.uboot; tftpboot 0x83f00000 $dtb; bootm 0x80008000 0x83000000 0x83f00000

MT7622 Bananapi, MT7531:

gmac0-and-gmac1-mt7622-bananapi-bpi-r64.dtb

tftpboot 0x40000000 arm64-Image; tftpboot 0x45000000 arm64-rootfs.cpio.uboot; tftpboot 0x4a000000 $dtb; booti 0x40000000 0x45000000 0x4a000000

MT7623 Bananapi, standalone MT7530:

rgmii-only-gmac0-mt7623n-bananapi-bpi-r2.dtb
gmac0-and-gmac1-mt7623n-bananapi-bpi-r2.dtb

tftpboot 0x80008000 arm-zImage; tftpboot 0x83000000 arm-rootfs.cpio.uboot; tftpboot 0x83f00000 $dtb; bootz 0x80008000 0x83000000 0x83f00000

This patch series is the continuation of the one linked below.

https://lore.kernel.org/netdev/20230522121532.86610-1-arinc.unal@arinc9.com/

Arınç

Arınç ÜNAL (15):
  net: dsa: mt7530: always trap frames to active CPU port on MT7530
  net: dsa: mt7530: use p5_interface_select as data type for p5_intf_sel
  net: dsa: mt7530: store port 5 SGMII capability of MT7531
  net: dsa: mt7530: improve comments regarding port 5 and 6
  net: dsa: mt7530: improve code path for setting up port 5
  net: dsa: mt7530: do not set priv->p5_interface on mt7530_setup_port5()
  net: dsa: mt7530: do not run mt7530_setup_port5() if port 5 is disabled
  net: dsa: mt7530: empty default case on mt7530_setup_port5()
  net: dsa: mt7530: call port 6 setup from mt7530_mac_config()
  net: dsa: mt7530: remove pad_setup function pointer
  net: dsa: mt7530: move XTAL check to mt7530_setup()
  net: dsa: mt7530: move enabling port 6 to mt7530_setup_port6()
  net: dsa: mt7530: simplify mt7530_setup_port6() and change to void
  net: dsa: mt7530: correct port capabilities of MT7988
  net: dsa: mt7530: do not clear config->supported_interfaces

 drivers/net/dsa/mt7530-mdio.c |   7 +-
 drivers/net/dsa/mt7530.c      | 283 ++++++++++++++++---------------------
 drivers/net/dsa/mt7530.h      |  19 +--
 3 files changed, 137 insertions(+), 172 deletions(-)





More information about the Linux-mediatek mailing list