Aw: Re: Re: Re: Re: Re: [PATCH v3 0/5] arm: dts: mt7623: relocate gmacs, mt7530 switch, and add port at 5

Matthias Brugger matthias.bgg at gmail.com
Mon May 29 06:40:24 PDT 2023



On 12/04/2023 19:06, Arınç ÜNAL wrote:
> On 12.04.2023 19:53, Frank Wunderlich wrote:
>> Hi
>>
>>> Gesendet: Mittwoch, 12. April 2023 um 18:21 Uhr
>>> Von: "Arınç ÜNAL" <arinc.unal at arinc9.com>
>>>> thanks, it changes the master when i upgrade iproute to 6.1 (from debian 
>>>> bullseye-backports), but i cannot do any traffic on it after switching to 
>>>> gmac1...
>>>>
>>>> 5: wan at eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state 
>>>> UP group default qlen 1000
>>>>       link/ether f2:d2:51:56:cd:3d brd ff:ff:ff:ff:ff:ff
>>>>       inet 192.168.0.11/24 scope global wan
>>>>          valid_lft forever preferred_lft forever
>>>>
>>>> see no p5-TX/gmac-rx
>>
>>> Did you apply the vlan and flooding fix patches from Richard?
>>
>> have now applied all patches i've found from richard (which are all rejected):
>>
>> fe4495bb3cc2 2023-02-12 Fix setting up CPU and User ports to be in the correct 
>> mode during setup and when toggling vlan_filtering on a bridge port.  (HEAD -> 
>> 6.3-rc)
>> b0641f3e1a69 2023-02-12 Fix Flooding: Disable by default on User ports and 
>> Enable on CPU ports
>> cb04b3451524 2023-02-12 Do not add all User ports to the CPU by default. This 
>> will break Multi CPU when added a seperate patch. It will be overwritten by 
>> .port_enable and since we are forcing output to a port via the Special Tag 
>> this is not needed.
>>
>> and now it seems working and is clear ;)
>>
>> root at bpi-r2:~# ip l show wan
>> 5: wan at eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP 
>> mode DEFAULT group default qlen 1000
>>      link/ether f2:d2:51:56:cd:3d brd ff:ff:ff:ff:ff:ff
>>
>> iperf3
>> [ ID] Interval           Transfer     Bitrate         Retr
>> [  5]   0.00-10.00  sec  1.09 GBytes   940 Mbits/sec    0             sender
>> [  5]   0.00-10.03  sec  1.09 GBytes   936 Mbits/sec                  receiver
>>
>>
>> iperf3 -R
>> [ ID] Interval           Transfer     Bitrate         Retr
>> [  5]   0.00-10.04  sec  1.09 GBytes   936 Mbits/sec    0             sender
>> [  5]   0.00-10.00  sec  1.09 GBytes   938 Mbits/sec                  receiver
>>
>>
>> how do you deal with these patches? do you include them into your mt7530 fixes 
>> series? they (and vladimirs preferred cpu-port) need to be applied before 
>> these DTS-changes
> 
> Dealing with this is the last step on my tasklist. Take a look:
> 
> https://arinc9.notion.site/mt7530-c-improvements-bbfdc2ceb958484b9627297b88bc6d4a
> 

I'm a bit lost here. @frank can this be merged now or are there still oustanding 
issues. It seems to me that not, but just in case...

Regards,
Matthias



More information about the Linux-mediatek mailing list