[PATCH v17 RESEND 1/3] leds: rgb: mt6370: Add MediaTek MT6370 current sink type LED Indicator support

ChiYuan Huang cy_huang at richtek.com
Mon Mar 6 18:23:02 PST 2023


Hi, Lee:

Thanks's for the reviewing.
To prevent the misunderstanding, reply as below.
No reply means will do.

On Sun, Mar 05, 2023 at 08:55:33AM +0000, Lee Jones wrote:
> On Thu, 23 Feb 2023, ChiaEn Wu wrote:
> 
> > From: ChiYuan Huang <cy_huang at richtek.com>
> > 
> > The MediaTek MT6370 is a highly-integrated smart power management IC,
> > which includes a single cell Li-Ion/Li-Polymer switching battery
> > charger, a USB Type-C & Power Delivery (PD) controller, dual
> > Flash LED current sources, a RGB LED driver, a backlight WLED driver,
> > a display bias driver and a general LDO for portable devices.
> > 
> > Add support for the MediaTek MT6370 Current Sink Type LED Indicator
> > driver. It can control four channels current-sink RGB LEDs with 3 modes:
> > constant current, PWM, and breath mode.
> > 
> > Acked-by: Jacek Anaszewski <jacek.anaszewski at gmail.com>
> > Co-developed-by: Alice Chen <alice_chen at richtek.com>
> > Signed-off-by: Alice Chen <alice_chen at richtek.com>
> > Signed-off-by: ChiYuan Huang <cy_huang at richtek.com>
> > Signed-off-by: ChiaEn Wu <chiaen_wu at richtek.com>
> > ---
> > v17
> > - Update the year of Copyright from 2022 to 2023
> > 
> > ---
> >  drivers/leds/rgb/Kconfig           |   13 +
> >  drivers/leds/rgb/Makefile          |    1 +
> >  drivers/leds/rgb/leds-mt6370-rgb.c | 1009 ++++++++++++++++++++++++++++++++++++
> >  3 files changed, 1023 insertions(+)
> >  create mode 100644 drivers/leds/rgb/leds-mt6370-rgb.c
> 
> In generally, this is really nicely done.  Great job.
> 
> Just a few niggles, then you'll be good to go.
>  
> > diff --git a/drivers/leds/rgb/Kconfig b/drivers/leds/rgb/Kconfig
> > index 204cf47..7d86bb2 100644
> > --- a/drivers/leds/rgb/Kconfig
> > +++ b/drivers/leds/rgb/Kconfig
> > @@ -26,4 +26,17 @@ config LEDS_QCOM_LPG
> >  
> >  	  If compiled as a module, the module will be named leds-qcom-lpg.
> >  
> > +config LEDS_MT6370_RGB
> > +	tristate "LED Support for MediaTek MT6370 PMIC"
> > +	depends on MFD_MT6370
> > +	select LINEAR_RANGE
> > +	help
> > +	  Say Y here to enable support for MT6370_RGB LED device.
> > +	  In MT6370, there are four channel current-sink LED drivers that
> > +	  support hardware pattern for constant current, PWM, and breath mode.
> > +	  Isink4 channel can also be used as a CHG_VIN power good indicator.
> > +
> > +	  This driver can also be built as a module. If so, the module
> > +	  will be called "leds-mt6370-rgb".
> > +
> >  endif # LEDS_CLASS_MULTICOLOR
> > diff --git a/drivers/leds/rgb/Makefile b/drivers/leds/rgb/Makefile
> > index 0675bc0..8c01daf 100644
> > --- a/drivers/leds/rgb/Makefile
> > +++ b/drivers/leds/rgb/Makefile
> > @@ -2,3 +2,4 @@
> >  
> >  obj-$(CONFIG_LEDS_PWM_MULTICOLOR)	+= leds-pwm-multicolor.o
> >  obj-$(CONFIG_LEDS_QCOM_LPG)		+= leds-qcom-lpg.o
> > +obj-$(CONFIG_LEDS_MT6370_RGB)		+= leds-mt6370-rgb.o
> > diff --git a/drivers/leds/rgb/leds-mt6370-rgb.c b/drivers/leds/rgb/leds-mt6370-rgb.c
> > new file mode 100644
> > index 00000000..185d5d7
> > --- /dev/null
> > +++ b/drivers/leds/rgb/leds-mt6370-rgb.c
> > @@ -0,0 +1,1009 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/*
> > + * Copyright (C) 2023 Richtek Technology Corp.
> > + *
> > + * Authors:
> > + *   ChiYuan Huang <cy_huang at richtek.com>
> > + *   Alice Chen <alice_chen at richtek.com>
> > + */
> > +
> > +#include <linux/bitops.h>
> > +#include <linux/kernel.h>
> > +#include <linux/leds.h>
> > +#include <linux/led-class-multicolor.h>
> > +#include <linux/linear_range.h>
> > +#include <linux/mod_devicetable.h>
> > +#include <linux/module.h>
> > +#include <linux/mutex.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/property.h>
> > +#include <linux/regmap.h>
> > +#include <linux/util_macros.h>
> > +
> > +#include <asm/unaligned.h>
> > +
> > +enum {
> > +	MT6370_LED_ISNK1 = 0,
> > +	MT6370_LED_ISNK2,
> > +	MT6370_LED_ISNK3,
> > +	MT6370_LED_ISNK4,
> > +	MT6370_MAX_LEDS
> > +};
> > +
> > +enum mt6370_led_mode {
> > +	MT6370_LED_PWM_MODE = 0,
> > +	MT6370_LED_BREATH_MODE,
> > +	MT6370_LED_REG_MODE,
> > +	MT6370_LED_MAX_MODE
> > +};
> > +
> > +enum mt6370_led_field {
> > +	F_RGB_EN = 0,
> > +	F_CHGIND_EN,
> > +	F_LED1_CURR,
> > +	F_LED2_CURR,
> > +	F_LED3_CURR,
> > +	F_LED4_CURR,
> > +	F_LED1_MODE,
> > +	F_LED2_MODE,
> > +	F_LED3_MODE,
> > +	F_LED4_MODE,
> > +	F_LED1_DUTY,
> > +	F_LED2_DUTY,
> > +	F_LED3_DUTY,
> > +	F_LED4_DUTY,
> > +	F_LED1_FREQ,
> > +	F_LED2_FREQ,
> > +	F_LED3_FREQ,
> > +	F_LED4_FREQ,
> > +	F_MAX_FIELDS
> > +};
> > +
> > +enum mt6370_led_ranges {
> > +	R_LED123_CURR = 0,
> > +	R_LED4_CURR,
> > +	R_LED_TRFON,
> > +	R_LED_TOFF,
> > +	R_MAX_RANGES
> > +};
> > +
> > +enum mt6370_pattern {
> > +	P_LED_TR1 = 0,
> > +	P_LED_TR2,
> > +	P_LED_TF1,
> > +	P_LED_TF2,
> > +	P_LED_TON,
> > +	P_LED_TOFF,
> > +	P_MAX_PATTERNS
> > +};
> > +
> > +#define MT6370_REG_DEV_INFO			0x100
> > +#define MT6370_REG_RGB1_DIM			0x182
> > +#define MT6370_REG_RGB2_DIM			0x183
> > +#define MT6370_REG_RGB3_DIM			0x184
> > +#define MT6370_REG_RGB_EN			0x185
> > +#define MT6370_REG_RGB1_ISNK			0x186
> > +#define MT6370_REG_RGB2_ISNK			0x187
> > +#define MT6370_REG_RGB3_ISNK			0x188
> > +#define MT6370_REG_RGB1_TR			0x189
> > +#define MT6370_REG_RGB_CHRIND_DIM		0x192
> > +#define MT6370_REG_RGB_CHRIND_CTRL		0x193
> > +#define MT6370_REG_RGB_CHRIND_TR		0x194
> > +
> > +#define MT6372_REG_RGB_EN			0x182
> > +#define MT6372_REG_RGB1_ISNK			0x183
> > +#define MT6372_REG_RGB2_ISNK			0x184
> > +#define MT6372_REG_RGB3_ISNK			0x185
> > +#define MT6372_REG_RGB4_ISNK			0x186
> > +#define MT6372_REG_RGB1_DIM			0x187
> > +#define MT6372_REG_RGB2_DIM			0x188
> > +#define MT6372_REG_RGB3_DIM			0x189
> > +#define MT6372_REG_RGB4_DIM			0x18A
> > +#define MT6372_REG_RGB12_FREQ			0x18B
> > +#define MT6372_REG_RGB34_FREQ			0x18C
> > +#define MT6372_REG_RGB1_TR			0x18D
> > +
> > +#define MT6370_VENID_MASK			GENMASK(7, 4)
> 
> Vendor?  Defines should be self documenting.
> 
> What does this save over "VENDOR_ID"?
>
So 'MT6370_VENDOR_ID_MASK'? And will define all used VENDOR_ID.
> > +#define MT6370_CHEN_BIT(id)			BIT(MT6370_LED_ISNK4 - id)
> > +#define MT6370_VIRTUAL_MULTICOLOR		5
> > +#define MC_CHANNEL_NUM				3
> > +#define MT6370_PWM_DUTY				(BIT(5) - 1)
> > +#define MT6372_PWM_DUTY				(BIT(8) - 1)
> > +
> > +struct mt6370_led {
> > +	/*
> > +	 * If the color of the LED in DT is set to
> > +	 *   - 'LED_COLOR_ID_RGB'
> > +	 *   - 'LED_COLOR_ID_MULTI'
> > +	 * The member 'index' of this struct will be set to
> > +	 * 'MT6370_VIRTUAL_MULTICOLOR'.
> > +	 * If so, this LED will choose 'struct led_classdev_mc mc' to use.
> > +	 * Instead, if the member 'index' of this struct is set to
> > +	 * 'MT6370_LED_ISNK1' ~ 'MT6370_LED_ISNK4', then this LED will choose
> > +	 * 'struct led_classdev isink' to use.
> > +	 */
> > +	union {
> > +		struct led_classdev isink;
> > +		struct led_classdev_mc mc;
> > +	};
> > +	struct mt6370_priv *priv;
> > +	enum led_default_state default_state;
> > +	u32 index;
> > +};
> > +
> > +struct mt6370_pdata {
> > +	const unsigned int *tfreq;
> > +	unsigned int tfreq_len;
> > +	u16 reg_rgb1_tr;
> > +	s16 reg_rgb_chrind_tr;
> > +	u8 pwm_duty;
> > +};
> > +
> > +struct mt6370_priv {
> > +	/* Per LED access lock */
> > +	struct mutex lock;
> > +	struct regmap *regmap;
> > +	struct regmap_field *fields[F_MAX_FIELDS];
> > +	const struct reg_field *reg_fields;
> > +	const struct linear_range *ranges;
> > +	struct reg_cfg *reg_cfgs;
> > +	const struct mt6370_pdata *pdata;
> > +	unsigned int leds_count;
> > +	unsigned int leds_active;
> > +	struct mt6370_led leds[];
> > +};
> > +
> > +static const struct reg_field common_reg_fields[F_MAX_FIELDS] = {
> > +	[F_RGB_EN]	= REG_FIELD(MT6370_REG_RGB_EN, 4, 7),
> > +	[F_CHGIND_EN]	= REG_FIELD(MT6370_REG_RGB_CHRIND_DIM, 7, 7),
> > +	[F_LED1_CURR]	= REG_FIELD(MT6370_REG_RGB1_ISNK, 0, 2),
> > +	[F_LED2_CURR]	= REG_FIELD(MT6370_REG_RGB2_ISNK, 0, 2),
> > +	[F_LED3_CURR]	= REG_FIELD(MT6370_REG_RGB3_ISNK, 0, 2),
> > +	[F_LED4_CURR]	= REG_FIELD(MT6370_REG_RGB_CHRIND_CTRL, 0, 1),
> > +	[F_LED1_MODE]	= REG_FIELD(MT6370_REG_RGB1_DIM, 5, 6),
> > +	[F_LED2_MODE]	= REG_FIELD(MT6370_REG_RGB2_DIM, 5, 6),
> > +	[F_LED3_MODE]	= REG_FIELD(MT6370_REG_RGB3_DIM, 5, 6),
> > +	[F_LED4_MODE]	= REG_FIELD(MT6370_REG_RGB_CHRIND_DIM, 5, 6),
> > +	[F_LED1_DUTY]	= REG_FIELD(MT6370_REG_RGB1_DIM, 0, 4),
> > +	[F_LED2_DUTY]	= REG_FIELD(MT6370_REG_RGB2_DIM, 0, 4),
> > +	[F_LED3_DUTY]	= REG_FIELD(MT6370_REG_RGB3_DIM, 0, 4),
> > +	[F_LED4_DUTY]	= REG_FIELD(MT6370_REG_RGB_CHRIND_DIM, 0, 4),
> > +	[F_LED1_FREQ]	= REG_FIELD(MT6370_REG_RGB1_ISNK, 3, 5),
> > +	[F_LED2_FREQ]	= REG_FIELD(MT6370_REG_RGB2_ISNK, 3, 5),
> > +	[F_LED3_FREQ]	= REG_FIELD(MT6370_REG_RGB3_ISNK, 3, 5),
> > +	[F_LED4_FREQ]	= REG_FIELD(MT6370_REG_RGB_CHRIND_CTRL, 2, 4),
> > +};
> > +
> > +static const struct reg_field mt6372_reg_fields[F_MAX_FIELDS] = {
> > +	[F_RGB_EN]	= REG_FIELD(MT6372_REG_RGB_EN, 4, 7),
> > +	[F_CHGIND_EN]	= REG_FIELD(MT6372_REG_RGB_EN, 3, 3),
> > +	[F_LED1_CURR]	= REG_FIELD(MT6372_REG_RGB1_ISNK, 0, 3),
> > +	[F_LED2_CURR]	= REG_FIELD(MT6372_REG_RGB2_ISNK, 0, 3),
> > +	[F_LED3_CURR]	= REG_FIELD(MT6372_REG_RGB3_ISNK, 0, 3),
> > +	[F_LED4_CURR]	= REG_FIELD(MT6372_REG_RGB4_ISNK, 0, 3),
> > +	[F_LED1_MODE]	= REG_FIELD(MT6372_REG_RGB1_ISNK, 6, 7),
> > +	[F_LED2_MODE]	= REG_FIELD(MT6372_REG_RGB2_ISNK, 6, 7),
> > +	[F_LED3_MODE]	= REG_FIELD(MT6372_REG_RGB3_ISNK, 6, 7),
> > +	[F_LED4_MODE]	= REG_FIELD(MT6372_REG_RGB4_ISNK, 6, 7),
> > +	[F_LED1_DUTY]	= REG_FIELD(MT6372_REG_RGB1_DIM, 0, 7),
> > +	[F_LED2_DUTY]	= REG_FIELD(MT6372_REG_RGB2_DIM, 0, 7),
> > +	[F_LED3_DUTY]	= REG_FIELD(MT6372_REG_RGB3_DIM, 0, 7),
> > +	[F_LED4_DUTY]	= REG_FIELD(MT6372_REG_RGB4_DIM, 0, 7),
> > +	[F_LED1_FREQ]	= REG_FIELD(MT6372_REG_RGB12_FREQ, 5, 7),
> > +	[F_LED2_FREQ]	= REG_FIELD(MT6372_REG_RGB12_FREQ, 2, 4),
> > +	[F_LED3_FREQ]	= REG_FIELD(MT6372_REG_RGB34_FREQ, 5, 7),
> > +	[F_LED4_FREQ]	= REG_FIELD(MT6372_REG_RGB34_FREQ, 2, 4),
> > +};
> > +
> > +/* Current unit: microamp, time unit: millisecond */
> > +static const struct linear_range common_led_ranges[R_MAX_RANGES] = {
> > +	[R_LED123_CURR]	= { 4000, 1, 6, 4000 },
> > +	[R_LED4_CURR]	= { 2000, 1, 3, 2000 },
> > +	[R_LED_TRFON]	= { 125, 0, 15, 200 },
> > +	[R_LED_TOFF]	= { 250, 0, 15, 400 },
> > +};
> > +
> > +static const struct linear_range mt6372_led_ranges[R_MAX_RANGES] = {
> > +	[R_LED123_CURR]	= { 2000, 1, 14, 2000 },
> > +	[R_LED4_CURR]	= { 2000, 1, 14, 2000 },
> > +	[R_LED_TRFON]	= { 125, 0, 15, 250 },
> > +	[R_LED_TOFF]	= { 250, 0, 15, 500 },
> > +};
> > +
> > +static const unsigned int common_tfreqs[] = {
> > +	10000, 5000, 2000, 1000, 500, 200, 5, 1,
> > +};
> > +
> > +static const unsigned int mt6372_tfreqs[] = {
> > +	8000, 4000, 2000, 1000, 500, 250, 8, 4,
> > +};
> > +
> > +static const struct mt6370_pdata common_pdata = {
> > +	.tfreq = common_tfreqs,
> > +	.tfreq_len = ARRAY_SIZE(common_tfreqs),
> > +	.pwm_duty = MT6370_PWM_DUTY,
> > +	.reg_rgb1_tr = MT6370_REG_RGB1_TR,
> > +	.reg_rgb_chrind_tr = MT6370_REG_RGB_CHRIND_TR,
> > +};
> > +
> > +static const struct mt6370_pdata mt6372_pdata = {
> > +	.tfreq = mt6372_tfreqs,
> > +	.tfreq_len = ARRAY_SIZE(mt6372_tfreqs),
> > +	.pwm_duty = MT6372_PWM_DUTY,
> > +	.reg_rgb1_tr = MT6372_REG_RGB1_TR,
> > +	.reg_rgb_chrind_tr = -1,
> > +};
> > +
> > +static enum mt6370_led_field mt6370_get_led_current_field(unsigned int led_no)
> > +{
> > +	switch (led_no) {
> > +	case MT6370_LED_ISNK1:
> > +		return F_LED1_CURR;
> > +	case MT6370_LED_ISNK2:
> > +		return F_LED2_CURR;
> > +	case MT6370_LED_ISNK3:
> > +		return F_LED3_CURR;
> > +	default:
> > +		return F_LED4_CURR;
> > +	}
> > +}
> > +
> > +static int mt6370_set_led_brightness(struct mt6370_priv *priv,
> > +				     unsigned int led_no, unsigned int level)
> > +{
> > +	enum mt6370_led_field sel_field;
> > +
> > +	sel_field = mt6370_get_led_current_field(led_no);
> > +
> > +	return regmap_field_write(priv->fields[sel_field], level);
> > +}
> > +
> > +static int mt6370_get_led_brightness(struct mt6370_priv *priv,
> > +				     unsigned int led_no, unsigned int *level)
> > +{
> > +	enum mt6370_led_field sel_field;
> > +
> > +	sel_field = mt6370_get_led_current_field(led_no);
> > +
> > +	return regmap_field_read(priv->fields[sel_field], level);
> > +}
> > +
> > +static int mt6370_set_led_duty(struct mt6370_priv *priv, unsigned int led_no,
> > +			       unsigned int ton, unsigned int toff)
> > +{
> > +	const struct mt6370_pdata *pdata = priv->pdata;
> > +	enum mt6370_led_field sel_field;
> > +	unsigned int divisor, ratio;
> > +
> > +	divisor = pdata->pwm_duty;
> > +	ratio = ton * divisor / (ton + toff);
> > +
> > +	switch (led_no) {
> > +	case MT6370_LED_ISNK1:
> > +		sel_field = F_LED1_DUTY;
> > +		break;
> > +	case MT6370_LED_ISNK2:
> > +		sel_field = F_LED2_DUTY;
> > +		break;
> > +	case MT6370_LED_ISNK3:
> > +		sel_field = F_LED3_DUTY;
> > +		break;
> > +	default:
> > +		sel_field = F_LED4_DUTY;
> > +		break;
> > +	}
> > +
> > +	return regmap_field_write(priv->fields[sel_field], ratio);
> > +}
> > +
> > +static int mt6370_set_led_freq(struct mt6370_priv *priv, unsigned int led_no,
> > +			       unsigned int ton, unsigned int toff)
> > +{
> > +	const struct mt6370_pdata *pdata = priv->pdata;
> > +	enum mt6370_led_field sel_field;
> > +	unsigned int tfreq_len = pdata->tfreq_len;
> > +	unsigned int tsum, sel;
> > +
> > +	tsum = ton + toff;
> > +
> > +	if (tsum > pdata->tfreq[0] || tsum < pdata->tfreq[tfreq_len - 1])
> > +		return -EOPNOTSUPP;
> > +
> > +	sel = find_closest_descending(tsum, pdata->tfreq, tfreq_len);
> > +
> > +	switch (led_no) {
> > +	case MT6370_LED_ISNK1:
> > +		sel_field = F_LED1_FREQ;
> > +		break;
> > +	case MT6370_LED_ISNK2:
> > +		sel_field = F_LED2_FREQ;
> > +		break;
> > +	case MT6370_LED_ISNK3:
> > +		sel_field = F_LED3_FREQ;
> > +		break;
> > +	default:
> > +		sel_field = F_LED4_FREQ;
> > +		break;
> > +	}
> > +
> > +	return regmap_field_write(priv->fields[sel_field], sel);
> > +}
> > +
> > +static void mt6370_get_breath_reg_base(struct mt6370_priv *priv,
> > +				       unsigned int led_no, unsigned int *base)
> > +{
> > +	const struct mt6370_pdata *pdata = priv->pdata;
> > +
> > +	if (pdata->reg_rgb_chrind_tr < 0) {
> > +		*base = pdata->reg_rgb1_tr + led_no * 3;
> > +		return;
> > +	}
> > +
> > +	switch (led_no) {
> > +	case MT6370_LED_ISNK1:
> > +	case MT6370_LED_ISNK2:
> > +	case MT6370_LED_ISNK3:
> > +		*base = pdata->reg_rgb1_tr + led_no * 3;
> > +		break;
> > +	default:
> > +		*base = pdata->reg_rgb_chrind_tr;
> > +		break;
> > +	}
> > +}
> > +
> > +static int mt6370_gen_breath_pattern(struct mt6370_priv *priv,
> > +				     struct led_pattern *pattern, u32 len,
> > +				     u8 *pattern_val, u32 val_len)
> > +{
> > +	enum mt6370_led_ranges sel_range;
> > +	struct led_pattern *curr;
> > +	unsigned int sel;
> > +	u32 val = 0;
> > +	int i;
> > +
> > +	if (len < P_MAX_PATTERNS && val_len < P_MAX_PATTERNS / 2)
> > +		return -EINVAL;
> > +
> > +	/*
> > +	 * Pattern list
> > +	 * tr1:	 byte 0, b'[7: 4]
> 
> Perhaps this is standard formatting and I'm just not aware of it, but
> the space is throwing me and making me think twice.  Does this mean bits
> 7 through 4, so b'11110000?
>
Yes. like as you said. Sorry for the redudant space make you confused.
I'm not sure whether it's a standard formating or not.
Sometimes, in datasheet, we'll use this format to represent the bitfield for functions.
Your format is also good for it.
And which one is preferable?
> > +	 * tr2:	 byte 0, b'[3: 0]
> > +	 * tf1:	 byte 1, b'[7: 4]
> > +	 * tf2:	 byte 1, b'[3: 0]
> > +	 * ton:	 byte 2, b'[7: 4]
> > +	 * toff: byte 2, b'[3: 0]
> > +	 */
> > +	for (i = 0; i < P_MAX_PATTERNS; i++) {
> > +		curr = pattern + i;
> > +
> > +		sel_range = i == P_LED_TOFF ? R_LED_TOFF : R_LED_TRFON;
> > +
> > +		linear_range_get_selector_within(priv->ranges + sel_range,
> > +						 curr->delta_t, &sel);
> > +
> > +		if (i % 2) {
> > +			val |= sel;
> > +		} else {
> > +			val <<= 8;
> > +			val |= sel << 4;
> > +		}
> > +	}
> > +
> > +	put_unaligned_be24(val, pattern_val);
> > +
> > +	return 0;
> > +}
> > +
> > +static int mt6370_set_led_mode(struct mt6370_priv *priv, unsigned int led_no,
> > +			       enum mt6370_led_mode mode)
> > +{
> > +	enum mt6370_led_field sel_field;
> > +
> > +	switch (led_no) {
> > +	case MT6370_LED_ISNK1:
> > +		sel_field = F_LED1_MODE;
> > +		break;
> > +	case MT6370_LED_ISNK2:
> > +		sel_field = F_LED2_MODE;
> > +		break;
> > +	case MT6370_LED_ISNK3:
> > +		sel_field = F_LED3_MODE;
> > +		break;
> > +	default:
> > +		sel_field = F_LED4_MODE;
> > +		break;
> > +	}
> > +
> > +	return regmap_field_write(priv->fields[sel_field], mode);
> > +}
> > +
> > +static int mt6370_mc_brightness_set(struct led_classdev *lcdev,
> > +				    enum led_brightness level)
> > +{
> > +	struct led_classdev_mc *mccdev = lcdev_to_mccdev(lcdev);
> > +	struct mt6370_led *led = container_of(mccdev, struct mt6370_led, mc);
> > +	struct mt6370_priv *priv = led->priv;
> > +	struct mc_subled *subled;
> > +	unsigned int enable, disable;
> > +	int i, ret;
> > +
> > +	mutex_lock(&priv->lock);
> > +
> > +	led_mc_calc_color_components(mccdev, level);
> > +
> > +	ret = regmap_field_read(priv->fields[F_RGB_EN], &enable);
> > +	if (ret)
> > +		goto out_unlock;
> > +
> > +	disable = enable;
> > +
> > +	for (i = 0; i < mccdev->num_colors; i++) {
> > +		u32 brightness;
> > +
> > +		subled = mccdev->subled_info + i;
> > +		brightness = min(subled->brightness, lcdev->max_brightness);
> > +		disable &= ~MT6370_CHEN_BIT(subled->channel);
> > +
> > +		if (level == 0) {
> > +			enable &= ~MT6370_CHEN_BIT(subled->channel);
> > +
> > +			ret = mt6370_set_led_mode(priv, subled->channel,
> > +						  MT6370_LED_REG_MODE);
> 
> Please unify your line-wrap strategy.  In some places you are using the
> full 100-chars allowable and in many others, you line-wrap early.  Please
> go through the entire file and unwrap to 100-chars where appropriate.
> 
> You'll see what I mean as you re-read the file with this in mind.
> 
> > +			if (ret)
> > +				goto out_unlock;
> > +
> > +			continue;
> > +		}
> > +
> > +		if (brightness == 0) {
> > +			enable &= ~MT6370_CHEN_BIT(subled->channel);
> > +			continue;
> > +		}
> > +
> > +		enable |= MT6370_CHEN_BIT(subled->channel);
> > +
> > +		ret = mt6370_set_led_brightness(priv, subled->channel,
> > +						brightness);
> > +		if (ret)
> > +			goto out_unlock;
> > +	}
> > +
> > +	ret = regmap_field_write(priv->fields[F_RGB_EN], disable);
> > +	if (ret)
> > +		goto out_unlock;
> > +
> > +	ret = regmap_field_write(priv->fields[F_RGB_EN], enable);
> > +
> > +out_unlock:
> > +	mutex_unlock(&priv->lock);
> > +
> > +	return ret;
> > +}
> > +
> > +static int mt6370_mc_blink_set(struct led_classdev *lcdev,
> > +			       unsigned long *delay_on,
> > +			       unsigned long *delay_off)
> > +{
> > +	struct led_classdev_mc *mccdev = lcdev_to_mccdev(lcdev);
> > +	struct mt6370_led *led = container_of(mccdev, struct mt6370_led, mc);
> > +	struct mt6370_priv *priv = led->priv;
> > +	struct mc_subled *subled;
> > +	unsigned int enable, disable;
> > +	int i, ret;
> > +
> > +	mutex_lock(&priv->lock);
> > +
> > +	if (!*delay_on && !*delay_off)
> > +		*delay_on = *delay_off = 500;
> > +
> > +	ret = regmap_field_read(priv->fields[F_RGB_EN], &enable);
> > +	if (ret)
> > +		goto out_unlock;
> > +
> > +	disable = enable;
> > +
> > +	for (i = 0; i < mccdev->num_colors; i++) {
> > +		subled = mccdev->subled_info + i;
> > +
> > +		disable &= ~MT6370_CHEN_BIT(subled->channel);
> > +
> > +		ret = mt6370_set_led_duty(priv, subled->channel, *delay_on,
> > +					  *delay_off);
> > +		if (ret)
> > +			goto out_unlock;
> > +
> > +		ret = mt6370_set_led_freq(priv, subled->channel, *delay_on,
> > +					  *delay_off);
> > +		if (ret)
> > +			goto out_unlock;
> > +
> > +		ret = mt6370_set_led_mode(priv, subled->channel,
> > +					  MT6370_LED_PWM_MODE);
> > +		if (ret)
> > +			goto out_unlock;
> > +	}
> > +
> > +	/* Toggle to make pattern timing the same */
> > +	ret = regmap_field_write(priv->fields[F_RGB_EN], disable);
> > +	if (ret)
> > +		goto out_unlock;
> > +
> > +	ret = regmap_field_write(priv->fields[F_RGB_EN], enable);
> > +
> > +out_unlock:
> > +	mutex_unlock(&priv->lock);
> > +
> > +	return ret;
> > +}
> > +
> > +static int mt6370_mc_pattern_set(struct led_classdev *lcdev,
> > +			struct led_pattern *pattern, u32 len, int repeat)
> > +{
> > +	struct led_classdev_mc *mccdev = lcdev_to_mccdev(lcdev);
> > +	struct mt6370_led *led = container_of(mccdev, struct mt6370_led, mc);
> > +	struct mt6370_priv *priv = led->priv;
> > +	struct mc_subled *subled;
> > +	unsigned int reg_base, enable, disable;
> > +	u8 params[P_MAX_PATTERNS / 2];
> > +	int i, ret;
> > +
> > +	mutex_lock(&priv->lock);
> > +
> > +	ret = mt6370_gen_breath_pattern(priv, pattern, len, params,
> > +					sizeof(params));
> > +	if (ret)
> > +		goto out_unlock;
> > +
> > +	ret = regmap_field_read(priv->fields[F_RGB_EN], &enable);
> > +	if (ret)
> > +		goto out_unlock;
> > +
> > +	disable = enable;
> > +
> > +	for (i = 0; i < mccdev->num_colors; i++) {
> > +		subled = mccdev->subled_info + i;
> > +
> > +		mt6370_get_breath_reg_base(priv, subled->channel, &reg_base);
> > +		disable &= ~MT6370_CHEN_BIT(subled->channel);
> > +
> > +		ret = regmap_raw_write(priv->regmap, reg_base, params,
> > +				       sizeof(params));
> > +		if (ret)
> > +			goto out_unlock;
> > +
> > +		ret = mt6370_set_led_mode(priv, subled->channel,
> > +					  MT6370_LED_BREATH_MODE);
> > +		if (ret)
> > +			goto out_unlock;
> > +	}
> > +
> > +	/* Toggle to make pattern timing be the same */
> > +	ret = regmap_field_write(priv->fields[F_RGB_EN], disable);
> > +	if (ret)
> > +		goto out_unlock;
> > +
> > +	ret = regmap_field_write(priv->fields[F_RGB_EN], enable);
> > +
> > +out_unlock:
> > +	mutex_unlock(&priv->lock);
> > +
> > +	return ret;
> > +}
> > +
> > +static inline int mt6370_mc_pattern_clear(struct led_classdev *lcdev)
> > +{
> > +	struct led_classdev_mc *mccdev = lcdev_to_mccdev(lcdev);
> > +	struct mt6370_led *led = container_of(mccdev, struct mt6370_led, mc);
> > +	struct mt6370_priv *priv = led->priv;
> > +	struct mc_subled *subled;
> > +	int i, ret;
> > +
> > +	mutex_lock(&led->priv->lock);
> > +
> > +	for (i = 0; i < mccdev->num_colors; i++) {
> > +		subled = mccdev->subled_info + i;
> > +
> > +		ret = mt6370_set_led_mode(priv, subled->channel,
> > +					  MT6370_LED_REG_MODE);
> > +		if (ret)
> > +			break;
> > +	}
> > +
> > +	mutex_unlock(&led->priv->lock);
> > +
> > +	return ret;
> > +}
> > +
> > +static int mt6370_isnk_brightness_set(struct led_classdev *lcdev,
> > +				      enum led_brightness level)
> > +{
> > +	struct mt6370_led *led = container_of(lcdev, struct mt6370_led, isink);
> > +	struct mt6370_priv *priv = led->priv;
> > +	unsigned int enable;
> > +	int ret;
> > +
> > +	mutex_lock(&priv->lock);
> > +
> > +	ret = regmap_field_read(priv->fields[F_RGB_EN], &enable);
> > +	if (ret)
> > +		goto out_unlock;
> > +
> > +	if (level == 0) {
> > +		enable &= ~MT6370_CHEN_BIT(led->index);
> > +
> > +		ret = mt6370_set_led_mode(priv, led->index,
> > +					  MT6370_LED_REG_MODE);
> > +		if (ret)
> > +			goto out_unlock;
> > +	} else {
> > +		enable |= MT6370_CHEN_BIT(led->index);
> > +
> > +		ret = mt6370_set_led_brightness(priv, led->index, level);
> > +		if (ret)
> > +			goto out_unlock;
> > +	}
> > +
> > +	ret = regmap_field_write(priv->fields[F_RGB_EN], enable);
> > +
> > +out_unlock:
> > +	mutex_unlock(&priv->lock);
> > +
> > +	return ret;
> > +}
> > +
> > +static int mt6370_isnk_blink_set(struct led_classdev *lcdev,
> > +				 unsigned long *delay_on,
> > +				 unsigned long *delay_off)
> > +{
> > +	struct mt6370_led *led = container_of(lcdev, struct mt6370_led, isink);
> > +	struct mt6370_priv *priv = led->priv;
> > +	int ret;
> > +
> > +	mutex_lock(&priv->lock);
> > +
> > +	if (!*delay_on && !*delay_off)
> > +		*delay_on = *delay_off = 500;
> > +
> > +	ret = mt6370_set_led_duty(priv, led->index, *delay_on, *delay_off);
> > +	if (ret)
> > +		goto out_unlock;
> > +
> > +	ret = mt6370_set_led_freq(priv, led->index, *delay_on, *delay_off);
> > +	if (ret)
> > +		goto out_unlock;
> > +
> > +	ret = mt6370_set_led_mode(priv, led->index, MT6370_LED_PWM_MODE);
> > +
> > +out_unlock:
> > +	mutex_unlock(&priv->lock);
> > +
> > +	return ret;
> > +}
> > +
> > +static int mt6370_isnk_pattern_set(struct led_classdev *lcdev,
> > +				   struct led_pattern *pattern, u32 len,
> > +				   int repeat)
> > +{
> > +	struct mt6370_led *led = container_of(lcdev, struct mt6370_led, isink);
> > +	struct mt6370_priv *priv = led->priv;
> > +	unsigned int reg_base;
> > +	u8 params[P_MAX_PATTERNS / 2];
> > +	int ret;
> > +
> > +	mutex_lock(&priv->lock);
> > +
> > +	ret = mt6370_gen_breath_pattern(priv, pattern, len, params,
> > +					sizeof(params));
> > +	if (ret)
> > +		goto out_unlock;
> > +
> > +	mt6370_get_breath_reg_base(priv, led->index, &reg_base);
> > +
> > +	ret = regmap_raw_write(priv->regmap, reg_base, params, sizeof(params));
> > +	if (ret)
> > +		goto out_unlock;
> > +
> > +	ret = mt6370_set_led_mode(priv, led->index, MT6370_LED_BREATH_MODE);
> > +
> > +out_unlock:
> > +	mutex_unlock(&priv->lock);
> > +
> > +	return ret;
> > +}
> > +
> > +static inline int mt6370_isnk_pattern_clear(struct led_classdev *lcdev)
> > +{
> > +	struct mt6370_led *led = container_of(lcdev, struct mt6370_led, isink);
> > +	struct mt6370_priv *priv = led->priv;
> > +	int ret;
> > +
> > +	mutex_lock(&led->priv->lock);
> > +	ret = mt6370_set_led_mode(priv, led->index, MT6370_LED_REG_MODE);
> > +	mutex_unlock(&led->priv->lock);
> > +
> > +	return ret;
> > +}
> > +
> > +static int mt6370_init_led_properties(struct device *dev,
> > +				      struct mt6370_led *led,
> > +				      struct led_init_data *init_data)
> > +{
> > +	struct mt6370_priv *priv = led->priv;
> > +	struct led_classdev *lcdev;
> > +	struct fwnode_handle *child;
> > +	enum mt6370_led_ranges sel_range;
> > +	u32 max_uA, max_level;
> > +	int ret;
> > +
> > +	if (led->index == MT6370_VIRTUAL_MULTICOLOR) {
> 
> Rather than having these huge if-else statements, please consider using
> a sub-function.
> 
I'll rewrite this as a sub function 'mt6370_assign_multicolor_info'.
start...
> > +		struct mc_subled *sub_led;
> > +		u32 num_color = 0;
> > +
> > +		sub_led = devm_kcalloc(dev, MC_CHANNEL_NUM, sizeof(*sub_led),
> > +				       GFP_KERNEL);
> > +		if (!sub_led)
> > +			return -ENOMEM;
> > +
> > +		fwnode_for_each_child_node(init_data->fwnode, child) {
> > +			u32 reg, color;
> > +
> > +			ret = fwnode_property_read_u32(child, "reg", &reg);
> > +			if (ret || reg > MT6370_LED_ISNK3 ||
> > +			    priv->leds_active & BIT(reg)) {
> > +				fwnode_handle_put(child);
> > +				return -EINVAL;
> > +			}
> > +
> > +			ret = fwnode_property_read_u32(child, "color", &color);
> > +			if (ret) {
> > +				fwnode_handle_put(child);
> > +				return dev_err_probe(dev, ret, "LED %d, no color specified\n",
> > +						     led->index);
> > +			}
> > +
> > +			priv->leds_active |= BIT(reg);
> > +			sub_led[num_color].color_index = color;
> > +			sub_led[num_color].channel = reg;
> > +			sub_led[num_color].intensity = 0;
> > +			num_color++;
> > +		}
> > +
> > +		if (num_color < 2)
> > +			return dev_err_probe(dev, -EINVAL,
> > +					     "Multicolor must include 2 or more LED channels\n");
> > +
> > +		led->mc.num_colors = num_color;
> > +		led->mc.subled_info = sub_led;
> > +
...end
> > +		lcdev = &led->mc.led_cdev;
> > +		lcdev->brightness_set_blocking = mt6370_mc_brightness_set;
> > +		lcdev->blink_set = mt6370_mc_blink_set;
> > +		lcdev->pattern_set = mt6370_mc_pattern_set;
> > +		lcdev->pattern_clear = mt6370_mc_pattern_clear;
> > +	} else {
> > +		lcdev = &led->isink;
> > +		lcdev->brightness_set_blocking = mt6370_isnk_brightness_set;
> > +		lcdev->blink_set = mt6370_isnk_blink_set;
> > +		lcdev->pattern_set = mt6370_isnk_pattern_set;
> > +		lcdev->pattern_clear = mt6370_isnk_pattern_clear;
> > +	}
> > +
> > +	ret = fwnode_property_read_u32(init_data->fwnode, "led-max-microamp",
> > +				       &max_uA);
> > +	if (ret) {
> > +		dev_warn(dev, "Not specified led-max-microamp, config to the minimum\n");
> > +		max_uA = 0;
> > +	}
> > +
> > +	if (led->index == MT6370_LED_ISNK4)
> > +		sel_range = R_LED4_CURR;
> > +	else
> > +		sel_range = R_LED123_CURR;
> > +
> > +	linear_range_get_selector_within(priv->ranges + sel_range, max_uA,
> > +					 &max_level);
> > +
> > +	lcdev->max_brightness = max_level;
> > +
> > +	led->default_state = led_init_default_state_get(init_data->fwnode);
> > +
> > +	return 0;
> > +}
> > +
> > +static int mt6370_isnk_init_default_state(struct mt6370_led *led)
> > +{
> > +	struct mt6370_priv *priv = led->priv;
> > +	unsigned int enable, level;
> > +	int ret;
> > +
> > +	ret = mt6370_get_led_brightness(priv, led->index, &level);
> > +	if (ret)
> > +		return ret;
> > +
> > +	ret = regmap_field_read(priv->fields[F_RGB_EN], &enable);
> > +	if (ret)
> > +		return ret;
> > +
> > +	if (!(enable & MT6370_CHEN_BIT(led->index)))
> > +		level = 0;
> > +
> > +	switch (led->default_state) {
> > +	case LEDS_DEFSTATE_ON:
> > +		led->isink.brightness = led->isink.max_brightness;
> > +		break;
> > +	case LEDS_DEFSTATE_KEEP:
> > +		led->isink.brightness = min(level, led->isink.max_brightness);
> > +		break;
> > +	default:
> > +		led->isink.brightness = 0;
> > +		break;
> > +	}
> > +
> > +	return mt6370_isnk_brightness_set(&led->isink, led->isink.brightness);
> > +}
> > +
> > +static int mt6370_led_register(struct device *dev, struct mt6370_led *led,
> > +			       struct led_init_data *init_data)
> > +{
> > +	struct mt6370_priv *priv = led->priv;
> > +	int ret;
> > +
> > +	if (led->index == MT6370_VIRTUAL_MULTICOLOR) {
> 
> This too could be split into separate functions to tidy things up a
> little.
>
Like as below?

if (led->index == MT6370_VIRTUAL_MULTICOLOR)
   return mt6370_multicolor_led_register(....)

if (led->index == MT6370_LED_ISNK4) {
    .....
}

ret = mt6370_init_isnk_default_state(...)

Since the multilor case directly return from the sub-function, else can be removed.
> > +		ret = mt6370_mc_brightness_set(&led->mc.led_cdev, 0);
> > +		if (ret)
> > +			return dev_err_probe(dev, ret, "Couldn't set multicolor brightness\n");
> > +
> > +		ret = devm_led_classdev_multicolor_register_ext(dev, &led->mc,
> > +								init_data);
> > +		if (ret)
> > +			return dev_err_probe(dev, ret, "Couldn't register multicolor\n");
> > +	} else {
> > +		if (led->index == MT6370_LED_ISNK4) {
> > +			ret = regmap_field_write(priv->fields[F_CHGIND_EN], 1);
> > +			if (ret)
> > +				return dev_err_probe(dev, ret, "Failed to set CHRIND to SW\n");
> > +		}
> > +
> > +		ret = mt6370_isnk_init_default_state(led);
> > +		if (ret)
> > +			return dev_err_probe(dev, ret, "Failed to init %d isnk state\n",
> > +					     led->index);
> > +
> > +		ret = devm_led_classdev_register_ext(dev, &led->isink,
> > +						     init_data);
> > +		if (ret)
> > +			return dev_err_probe(dev, ret, "Couldn't register isink %d\n", led->index);
> > +	}
> > +
> > +	return 0;
> > +}
> > +
> > +static int mt6370_check_vendor_info(struct mt6370_priv *priv)
> > +{
> > +	unsigned int devinfo, vid;
> > +	int ret;
> > +
> > +	ret = regmap_read(priv->regmap, MT6370_REG_DEV_INFO, &devinfo);
> > +	if (ret)
> > +		return ret;
> > +
> > +	vid = FIELD_GET(MT6370_VENID_MASK, devinfo);
> > +	if (vid == 0x9 || vid == 0xb) {
> 
> Are there nice human readable associates of these (vendor?) IDS?
>
For clearly understanding, I'll define these two as 'MT6372_VENDOR_ID' and 'MT6372C_VENDOR_ID'.
 
> > +		priv->reg_fields = mt6372_reg_fields;
> > +		priv->ranges = mt6372_led_ranges;
> > +		priv->pdata = &mt6372_pdata;
> > +	} else {
> > +		/* Common for MT6370/71 */
> > +		priv->reg_fields = common_reg_fields;
> > +		priv->ranges = common_led_ranges;
> > +		priv->pdata = &common_pdata;
> > +	}
> > +
> > +	return 0;
> > +}
> > +
> > +static int mt6370_leds_probe(struct platform_device *pdev)
> > +{
> > +	struct device *dev = &pdev->dev;
> > +	struct mt6370_priv *priv;
> > +	struct fwnode_handle *child;
> > +	size_t count;
> > +	unsigned int i = 0;
> > +	int ret;
> > +
> > +	count = device_get_child_node_count(dev);
> > +	if (!count || count > MT6370_MAX_LEDS)
> > +		return dev_err_probe(dev, -EINVAL,
> > +				     "No child node or node count over max LED number %zu\n",
> > +				      count);
> > +
> > +	priv = devm_kzalloc(dev, struct_size(priv, leds, count), GFP_KERNEL);
> > +	if (!priv)
> > +		return -ENOMEM;
> > +
> > +	priv->leds_count = count;
> > +	mutex_init(&priv->lock);
> > +
> > +	priv->regmap = dev_get_regmap(dev->parent, NULL);
> > +	if (!priv->regmap)
> > +		return dev_err_probe(dev, -ENODEV, "Failed to get parent regmap\n");
> > +
> > +	ret = mt6370_check_vendor_info(priv);
> > +	if (ret)
> > +		return dev_err_probe(dev, ret, "Failed to check vendor info\n");
> > +
> > +	ret = devm_regmap_field_bulk_alloc(dev, priv->regmap, priv->fields,
> > +					   priv->reg_fields, F_MAX_FIELDS);
> > +	if (ret)
> > +		return dev_err_probe(dev, ret, "Failed to allocate regmap field\n");
> > +
> > +	device_for_each_child_node(dev, child) {
> > +		struct mt6370_led *led = priv->leds + i++;
> > +		struct led_init_data init_data = { .fwnode = child };
> > +		u32 reg, color;
> > +
> > +		ret = fwnode_property_read_u32(child, "reg", &reg);
> > +		if (ret) {
> > +			fwnode_handle_put(child);
> > +			return dev_err_probe(dev, ret, "Failed to parse reg property\n");
> > +		}
> > +
> > +		if (reg >= MT6370_MAX_LEDS) {
> > +			fwnode_handle_put(child);
> > +			return dev_err_probe(dev, -EINVAL, "Error reg property number\n");
> > +		}
> > +
> > +		ret = fwnode_property_read_u32(child, "color", &color);
> > +		if (ret) {
> > +			fwnode_handle_put(child);
> > +			return dev_err_probe(dev, ret, "Failed to parse color property\n");
> > +		}
> > +
> > +		if (color == LED_COLOR_ID_RGB || color == LED_COLOR_ID_MULTI)
> > +			reg = MT6370_VIRTUAL_MULTICOLOR;
> > +
> > +		if (priv->leds_active & BIT(reg)) {
> > +			fwnode_handle_put(child);
> > +			return dev_err_probe(dev, -EINVAL, "Duplicate reg property\n");
> > +		}
> > +
> > +		priv->leds_active |= BIT(reg);
> > +
> > +		led->index = reg;
> > +		led->priv = priv;
> > +
> > +		ret = mt6370_init_led_properties(dev, led, &init_data);
> > +		if (ret) {
> > +			fwnode_handle_put(child);
> 
> I count 6 calls to fwnode_handle_put() here.
> 
> Please use a goto to divert the error handling to the bottom of the
> function where you call fwnode_handle_put() just once.
> 
> > +			return ret;
> > +		}
> > +
> > +		ret = mt6370_led_register(dev, led, &init_data);
> > +		if (ret) {
> > +			fwnode_handle_put(child);
> > +			return ret;
> > +		}
> > +	}
> > +
> > +	return 0;
> > +}
> > +
> > +static const struct of_device_id mt6370_rgbled_device_table[] = {
> > +	{ .compatible = "mediatek,mt6370-indicator" },
> > +	{}
> > +};
> > +MODULE_DEVICE_TABLE(of, mt6370_rgbled_device_table);
> > +
> > +static struct platform_driver mt6370_rgbled_driver = {
> > +	.driver = {
> > +		.name = "mt6370-indicator",
> > +		.of_match_table = mt6370_rgbled_device_table,
> > +	},
> > +	.probe = mt6370_leds_probe,
> > +};
> > +module_platform_driver(mt6370_rgbled_driver);
> > +
> > +MODULE_AUTHOR("Alice Chen <alice_chen at richtek.com>");
> > +MODULE_AUTHOR("ChiYuan Huang <cy_huang at richtek.com>");
> > +MODULE_DESCRIPTION("MediaTek MT6370 RGB LED Driver");
> > +MODULE_LICENSE("GPL");
> > -- 
> > 2.7.4
> > 
> 
> -- 
> Lee Jones [李琼斯]



More information about the Linux-mediatek mailing list