[PATCH 1/2] dt-bindings: pinctrl: add bindings for MT7981 SoC
Daniel Golle
daniel at makrotopia.org
Mon Jan 23 15:55:51 PST 2023
On Mon, Jan 23, 2023 at 04:59:43PM -0600, Rob Herring wrote:
> On Sun, Jan 22, 2023 at 06:23:55PM +0000, Daniel Golle wrote:
> > Add bindings for the MT7981 pinctrl driver, based on existing MT7986
> > pinctrl bindings.
>
> What existing bindings? A .txt file you need to remove, or undocumented,
> but in use somewhere (where?)?
What I meant to express is that I used the existing
mediatek,mt7986-pinctrl.yaml file as the template to create a similar
document for MT7981. I guess my English was not clear enough.
Maybe better like this?
"Add bindings for the MT7981 pinctrl driver. As MT7981 is simiar to
MT7986, the existing mediatek,mt7986-pinctrl.yaml was used as an example
to create a similar document covering MT7981."
>
> > Signed-off-by: Daniel Golle <daniel at makrotopia.org>
> > ---
> > .../pinctrl/mediatek,mt7981-pinctrl.yaml | 475 ++++++++++++++++++
> > 1 file changed, 475 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,mt7981-pinctrl.yaml
> >
> > diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt7981-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7981-pinctrl.yaml
> > new file mode 100644
> > index 0000000000000..e76fe0d5083a3
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7981-pinctrl.yaml
> > @@ -0,0 +1,475 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/pinctrl/mediatek,mt7981-pinctrl.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Mediatek MT7981 Pin Controller
> > +
> > +maintainers:
> > + - Daniel Golle <daniel at makrotopia.org>
> > +
> > +description: |+
>
> Don't need '|+' unless there are line endings to preserve.
>
> > + The MediaTek's MT7981 Pin controller is used to control SoC pins.
> > +
> > +properties:
> > + compatible:
> > + enum:
> > + - mediatek,mt7981-pinctrl
> > +
> > + reg:
> > + minItems: 9
> > + maxItems: 9
> > +
> > + reg-names:
> > + items:
> > + - const: gpio
> > + - const: iocfg_rt
> > + - const: iocfg_rm
> > + - const: iocfg_rb
> > + - const: iocfg_lb
> > + - const: iocfg_bl
> > + - const: iocfg_tm
> > + - const: iocfg_tl
> > + - const: eint
> > +
> > + gpio-controller: true
> > +
> > + "#gpio-cells":
> > + const: 2
> > + description: |
> > + Number of cells in GPIO specifier. Since the generic GPIO
> > + binding is used, the amount of cells must be specified as 2. See the below
> > + mentioned gpio binding representation for description of particular cells.
> > +
> > + gpio-ranges:
> > + minItems: 1
> > + maxItems: 5
> > + description: |
> > + GPIO valid number range.
> > +
> > + interrupt-controller: true
> > +
> > + interrupts:
> > + maxItems: 1
> > +
> > + "#interrupt-cells":
> > + const: 2
> > +
> > +allOf:
> > + - $ref: "pinctrl.yaml#"
>
> Drop quotes
>
> > +
> > +required:
> > + - compatible
> > + - reg
> > + - reg-names
> > + - gpio-controller
> > + - "#gpio-cells"
> > +
> > +patternProperties:
> > + '-pins$':
> > + type: object
> > + additionalProperties: false
> > +
> > + patternProperties:
> > + '.*mux.*':
>
> Just to be really clear: '^.*mux.*$'
>
> Really, if not already in use, it would be preferred if this was either
> a prefix or a suffix.
>
> > + type: object
> > + additionalProperties: false
> > + description: |
> > + pinmux configuration nodes.
> > +
> > + The following table shows the effective values of "group", "function"
> > + properties and chip pinout pins
> > +
> > + groups function pins (in pin#)
> > + ---------------------------------------------------------------------
> > + "wa_aice1" "wa_aice" 0, 1
> > + "wa_aice2" "wa_aice" 0, 1
> > + "wm_uart_0" "uart" 0, 1
> > + "dfd" "dfd" 0, 1, 4, 5
> > + "watchdog" "watchdog" 2
> > + "pcie_pereset" "pcie" 3
> > + "jtag" "jtag" 4, 5, 6, 7, 8
> > + "wm_jtag_0" "jtag" 4, 5, 6, 7, 8
> > + "wo0_jtag_0" "jtag" 9, 10, 11, 12, 13
> > + "uart2_0" "uart" 4, 5, 6, 7
> > + "gbe_led0" "led" 8
> > + "pta_ext_0" "pta" 4, 5, 6
> > + "pwm2" "pwm" 7
> > + "net_wo0_uart_txd_0" "uart" 8
> > + "spi1_0" "spi" 4, 5, 6, 7
> > + "i2c0_0" "i2c" 6, 7
> > + "dfd_ntrst" "dfd" 8
> > + "wm_aice1" "wa_aice" 9, 10
> > + "pwm0_0" "pwm" 13
> > + "pwm0_1" "pwm" 15
> > + "pwm1_0" "pwm" 14
> > + "pwm1_1" "pwm" 15
> > + "net_wo0_uart_txd_1" "uart" 14
> > + "net_wo0_uart_txd_2" "uart" 15
> > + "gbe_led1" "led" 13
> > + "pcm" "pcm" 9, 10, 11, 12, 13, 25
> > + "watchdog1" "watchdog" 13
> > + "udi" "udi" 9, 10, 11, 12, 13
> > + "drv_vbus" "usb" 14
> > + "emmc_45" "flash" 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25
> > + "snfi" "flash" 16, 17, 18, 19, 20, 21
> > + "spi0" "spi" 16, 17, 18, 19
> > + "spi0_wp_hold" "spi" 20, 21
> > + "spi1_1" "spi" 22, 23, 24, 25
> > + "spi2" "spi" 26, 27, 28, 29
> > + "spi2_wp_hold" "spi" 30, 31
> > + "uart1_0" "uart" 16, 17, 18, 19
> > + "uart1_1" "uart" 26, 27, 28, 29
> > + "uart2_1" "uart" 22, 23, 24, 25
> > + "pta_ext_1" "pta" 22, 23, 24
> > + "wm_aurt_1" "uart" 20, 21
> > + "wm_aurt_2" "uart" 30, 31
> > + "wm_jtag_1" "jtag" 20, 21, 22, 23, 24
> > + "wo0_jtag_1" "jtag" 25, 26, 27, 28, 29
> > + "wa_aice3" "wa_aice" 28, 20
> > + "wm_aice2" "wa_aice" 30, 31
> > + "i2c0_1" "i2c" 30, 31
> > + "u2_phy_i2c" "i2c" 30, 31
> > + "uart0" "uart" 32, 33
> > + "sgmii1_phy_i2c" "i2c" 32, 33
> > + "u3_phy_i2c" "i2c" 32, 33
> > + "sgmii0_phy_i2c" "i2c" 32, 33
> > + "pcie_clk" "pcie" 34
> > + "pcie_wake" "pcie" 35
> > + "i2c0_2" "i2c" 36, 37
> > + "smi_mdc_mdio" "eth" 36, 37
> > + "gbe_ext_mdc_mdio" "eth" 36, 37
> > + "wf0_mode1" "eth" 40, 41, 42, 43, 44, 45, 46, 47, 48,
> > + 49, 50, 51, 52, 53, 54, 55, 56
> > +
> > + "wf0_mode3" "eth" 45, 46, 47, 48, 49, 51
> > + "wf2g_led0" "led" 30
> > + "wf2g_led1" "led" 34
> > + "wf5g_led0" "led" 31
> > + "wf5g_led1" "led" 35
> > + "mt7531_int" "eth" 38
> > + "ant_sel" "ant" 14, 15, 16, 17, 18, 19, 20, 21, 22
> > + 23, 24, 25, 34, 35
> > +
> > + $ref: "/schemas/pinctrl/pinmux-node.yaml"
>
> Drop quotes.
>
> > + properties:
> > + function:
> > + description: |
>
> Don't need '|'.
>
> > + A string containing the name of the function to mux to the group.
> > + enum: [wa_aice, dfd, jtag, pta, pcm, udi, usb, ant, eth, i2c, led,
> > + pwm, spi, uart, watchdog, flash, pcie]
> > + groups:
> > + description: |
> > + An array of strings. Each string contains the name of a group.
>
> Blank line.
>
> > + required:
> > + - function
> > + - groups
> > +
> > + allOf:
> > + - if:
> > + properties:
> > + function:
> > + const: wa_aice
> > + then:
> > + properties:
> > + groups:
> > + enum: [wa_aice1, wa_aice2, wm_aice1_1, wa_aice3, wm_aice1_2]
> > + - if:
> > + properties:
> > + function:
> > + const: dfd
> > + then:
> > + properties:
> > + groups:
> > + enum: [dfd, dfd_ntrst]
> > + - if:
> > + properties:
> > + function:
> > + const: jtag
> > + then:
> > + properties:
> > + groups:
> > + enum: [jtag, wm_jtag_0, wo0_jtag_0, wo0_jtag_1, wm_jtag_1]
> > + - if:
> > + properties:
> > + function:
> > + const: pta
> > + then:
> > + properties:
> > + groups:
> > + enum: [pta_ext_0, pta_ext_1]
> > + - if:
> > + properties:
> > + function:
> > + const: pcm
> > + then:
> > + properties:
> > + groups:
> > + enum: [pcm]
> > + - if:
> > + properties:
> > + function:
> > + const: udi
> > + then:
> > + properties:
> > + groups:
> > + enum: [udi]
> > + - if:
> > + properties:
> > + function:
> > + const: usb
> > + then:
> > + properties:
> > + groups:
> > + enum: [drv_vbus]
> > + - if:
> > + properties:
> > + function:
> > + const: ant
> > + then:
> > + properties:
> > + groups:
> > + enum: [ant_sel]
> > + - if:
> > + properties:
> > + function:
> > + const: eth
> > + then:
> > + properties:
> > + groups:
> > + enum: [smi_mdc_mdio, gbe_ext_mdc_mdio, wf0_mode1, wf0_mode3,
> > + mt7531_int]
> > + - if:
> > + properties:
> > + function:
> > + const: i2c
> > + then:
> > + properties:
> > + groups:
> > + enum: [i2c0_0, i2c0_1, u2_phy_i2c, sgmii1_phy_i2c, u3_phy_i2c,
> > + sgmii0_phy_i2c, i2c0_2]
> > + - if:
> > + properties:
> > + function:
> > + const: led
> > + then:
> > + properties:
> > + groups:
> > + enum: [gbe_led0, gbe_led1, wf2g_led0, wf2g_led1, wf5g_led0, wf5g_led1]
> > + - if:
> > + properties:
> > + function:
> > + const: pwm
> > + then:
> > + properties:
> > + groups:
> > + items:
> > + enum: [pwm2, pwm0_0, pwm0_1, pwm1_0, pwm1_1]
> > + maxItems: 3
> > + - if:
> > + properties:
> > + function:
> > + const: spi
> > + then:
> > + properties:
> > + groups:
> > + items:
> > + enum: [spi1_0, spi0, spi0_wp_hold, spi1_1, spi2, spi2_wp_hold]
> > + maxItems: 4
> > + - if:
> > + properties:
> > + function:
> > + const: uart
> > + then:
> > + properties:
> > + groups:
> > + items:
> > + enum: [wm_uart_0, uart2_0, net_wo0_uart_txd_0,
> > + net_wo0_uart_txd_1, net_wo0_uart_txd_2, uart1_0,
> > + uart1_1, uart2_1, wm_aurt_1, wm_aurt_2, uart0]
> > + - if:
> > + properties:
> > + function:
> > + const: watchdog
> > + then:
> > + properties:
> > + groups:
> > + enum: [watchdog]
> > + - if:
> > + properties:
> > + function:
> > + const: flash
> > + then:
> > + properties:
> > + groups:
> > + items:
> > + enum: [emmc_45, snfi]
> > + maxItems: 1
> > + - if:
> > + properties:
> > + function:
> > + const: pcie
> > + then:
> > + properties:
> > + groups:
> > + items:
> > + enum: [pcie_clk, pcie_wake, pcie_pereset]
> > + maxItems: 3
> > + '.*conf.*':
>
> Same comments as 'mux'.
>
> > + type: object
> > + additionalProperties: false
> > + description: |
> > + pinconf configuration nodes.
> > + $ref: "/schemas/pinctrl/pincfg-node.yaml"
>
> Drop quotes.
>
> > +
> > + properties:
> > + pins:
> > + description: |
> > + An array of strings. Each string contains the name of a pin.
> > + items:
> > + enum: [GPIO_WPS, GPIO_RESET, SYS_WATCHDOG, PCIE_PERESET_N,
> > + JTAG_JTDO, JTAG_JTDI, JTAG_JTMS, JTAG_JTCLK, JTAG_JTRST_N,
> > + WO_JTAG_JTDO, WO_JTAG_JTDI, WO_JTAG_JTMS, WO_JTAG_JTCLK,
> > + WO_JTAG_JTRST_N, USB_VBUS, PWM0, SPI0_CLK, SPI0_MOSI,
> > + SPI0_MISO, SPI0_CS, SPI0_HOLD, SPI0_WP, SPI1_CLK, SPI1_MOSI,
> > + SPI1_MISO, SPI1_CS, SPI2_CLK, SPI2_MOSI, SPI2_MISO, SPI2_CS,
> > + SPI2_HOLD, SPI2_WP, UART0_RXD, UART0_TXD, PCIE_CLK_REQ,
> > + PCIE_WAKE_N, SMI_MDC, SMI_MDIO, GBE_INT, GBE_RESET,
> > + WF_DIG_RESETB, WF_CBA_RESETB, WF_XO_REQ, WF_TOP_CLK,
> > + WF_TOP_DATA, WF_HB1, WF_HB2, WF_HB3, WF_HB4, WF_HB0,
> > + WF_HB0_B, WF_HB5, WF_HB6, WF_HB7, WF_HB8, WF_HB9, WF_HB10]
> > + maxItems: 57
> > +
> > + bias-disable: true
> > +
> > + bias-pull-up:
> > + oneOf:
> > + - type: boolean
> > + description: normal pull up.
> > + - enum: [100, 101, 102, 103]
> > + description: |
> > + PUPD/R1/R0 pull down type. See MTK_PUPD_SET_R1R0 defines in
> > + dt-bindings/pinctrl/mt65xx.h.
> > +
> > + bias-pull-down:
> > + oneOf:
> > + - type: boolean
> > + description: normal pull down.
> > + - enum: [100, 101, 102, 103]
> > + description: |
> > + PUPD/R1/R0 pull down type. See MTK_PUPD_SET_R1R0 defines in
> > + dt-bindings/pinctrl/mt65xx.h.
> > +
> > + input-enable: true
> > +
> > + input-disable: true
> > +
> > + output-enable: true
> > +
> > + output-low: true
> > +
> > + output-high: true
> > +
> > + input-schmitt-enable: true
> > +
> > + input-schmitt-disable: true
> > +
> > + drive-strength:
> > + enum: [2, 4, 6, 8, 10, 12, 14, 16]
> > +
> > + mediatek,pull-up-adv:
> > + description: |
> > + Valid arguments for 'mediatek,pull-up-adv' are '0', '1', '2', '3'
> > + Pull up setings for 2 pull resistors, R0 and R1. Valid arguments
> > + are described as below:
> > + 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
> > + 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
> > + 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
> > + 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
> > + $ref: /schemas/types.yaml#/definitions/uint32
> > + enum: [0, 1, 2, 3]
> > +
> > + mediatek,pull-down-adv:
> > + description: |
> > + Valid arguments for 'mediatek,pull-up-adv' are '0', '1', '2', '3'
> > + Pull down setings for 2 pull resistors, R0 and R1. Valid arguments
> > + are described as below:
> > + 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
> > + 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
> > + 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
> > + 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
> > + $ref: /schemas/types.yaml#/definitions/uint32
> > + enum: [0, 1, 2, 3]
> > +
> > + required:
> > + - pins
> > +
> > +additionalProperties: false
> > +
> > +examples:
> > + - |
> > + #include <dt-bindings/interrupt-controller/irq.h>
> > + #include <dt-bindings/interrupt-controller/arm-gic.h>
> > + #include <dt-bindings/pinctrl/mt65xx.h>
> > +
> > + soc {
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + pio: pinctrl at 11d00000 {
> > + compatible = "mediatek,mt7981-pinctrl";
> > + reg = <0 0x11d00000 0 0x1000>,
> > + <0 0x11c00000 0 0x1000>,
> > + <0 0x11c10000 0 0x1000>,
> > + <0 0x11d20000 0 0x1000>,
> > + <0 0x11e00000 0 0x1000>,
> > + <0 0x11e20000 0 0x1000>,
> > + <0 0x11f00000 0 0x1000>,
> > + <0 0x11f10000 0 0x1000>,
> > + <0 0x1000b000 0 0x1000>;
> > + reg-names = "gpio", "iocfg_rt", "iocfg_rm",
> > + "iocfg_rb", "iocfg_lb", "iocfg_bl",
> > + "iocfg_tm", "iocfg_tl", "eint";
> > + gpio-controller;
> > + #gpio-cells = <2>;
> > + gpio-ranges = <&pio 0 0 56>;
> > + interrupt-controller;
> > + interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
> > + interrupt-parent = <&gic>;
> > + #interrupt-cells = <2>;
> > +
> > + mdio_pins: mdio-pins {
> > + mux {
> > + function = "eth";
> > + groups = "smi_mdc_mdio";
> > + };
> > + };
> > +
> > + spi0_flash_pins: spi0-pins {
> > + mux {
> > + function = "spi";
> > + groups = "spi0", "spi0_wp_hold";
> > + };
> > +
> > + conf-pu {
> > + pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
> > + drive-strength = <MTK_DRIVE_8mA>;
> > + bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
> > + };
> > +
> > + conf-pd {
> > + pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
> > + drive-strength = <MTK_DRIVE_8mA>;
> > + bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
> > + };
> > + };
> > +
> > + pcie_pins: pcie-pins {
> > + mux {
> > + function = "pcie";
> > + groups = "pcie_clk", "pcie_wake", "pcie_pereset";
> > + };
> > + };
> > +
> > + };
> > + };
> > --
> > 2.39.1
> >
More information about the Linux-mediatek
mailing list