[PATCH 9/9] arm64: dts: mediatek: mt8186: Add display nodes

[Chen-Yu Tsai]

Hi,

On Wed, Jan 11, 2023 at 8:37 PM Allen-KH Cheng
<allen-kh.cheng at mediatek.com> wrote:
>
> Add display nodes and GCE info for MT8186 SoC. Also, add GCE
> (Global Command Engine) properties to the display nodes in order to
> enable the usage of the CMDQ (Command Queue), which is required for
> operating the display.
>
> Signed-off-by: Allen-KH Cheng <allen-kh.cheng at mediatek.com>
> ---
>  arch/arm64/boot/dts/mediatek/mt8186.dtsi | 128 +++++++++++++++++++++++
>  1 file changed, 128 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/mediatek/mt8186.dtsi b/arch/arm64/boot/dts/mediatek/mt8186.dtsi
> index eab30ab01572..8670d37970ef 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8186.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt8186.dtsi
> @@ -5,6 +5,7 @@
>   */
>  /dts-v1/;
>  #include <dt-bindings/clock/mt8186-clk.h>
> +#include <dt-bindings/gce/mt8186-gce.h>
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
>  #include <dt-bindings/interrupt-controller/irq.h>
>  #include <dt-bindings/memory/mt8186-memory-port.h>
> @@ -632,6 +633,15 @@
>                         clocks = <&clk13m>;
>                 };
>
> +               gce: mailbox at 1022c000 {
> +                       compatible = "mediatek,mt8186-gce";
> +                       reg = <0 0X1022c000 0 0x4000>;
> +                       interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH 0>;
> +                       #mbox-cells = <2>;
> +                       clocks = <&infracfg_ao CLK_INFRA_AO_GCE>;
> +                       clock-names = "gce";
> +               };
> +
>                 scp: scp at 10500000 {
>                         compatible = "mediatek,mt8186-scp";
>                         reg = <0 0x10500000 0 0x40000>,
> @@ -1197,6 +1207,20 @@
>                         reg = <0 0x14000000 0 0x1000>;
>                         #clock-cells = <1>;
>                         #reset-cells = <1>;
> +                       mboxes = <&gce 0 CMDQ_THR_PRIO_HIGHEST>,
> +                                <&gce 1 CMDQ_THR_PRIO_HIGHEST>;
> +                       mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0 0x1000>;
> +               };
> +
> +               mutex: mutex at 14001000 {
> +                       compatible = "mediatek,mt8186-disp-mutex";
> +                       reg = <0 0x14001000 0 0x1000>;
> +                       clocks = <&mmsys CLK_MM_DISP_MUTEX0>;
> +                       interrupts = <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH 0>;
> +                       mediatek,gce-client-reg = <&gce SUBSYS_1401XXXX 0x1000 0x1000>;
> +                       mediatek,gce-events = <CMDQ_EVENT_DISP_STREAM_DONE_ENG_EVENT_0>,
> +                                             <CMDQ_EVENT_DISP_STREAM_DONE_ENG_EVENT_1>;
> +                       power-domains = <&spm MT8186_POWER_DOMAIN_DIS>;
>                 };
>
>                 smi_common: smi at 14002000 {
> @@ -1230,6 +1254,49 @@
>                         power-domains = <&spm MT8186_POWER_DOMAIN_DIS>;
>                 };
>
> +               ovl0: ovl at 14005000 {

If there's only one instance, you could drop the trailing zero. Same
for all the other nodes.

> +                       compatible = "mediatek,mt8186-disp-ovl",
> +                                    "mediatek,mt8192-disp-ovl";
> +                       reg = <0 0x14005000 0 0x1000>;
> +                       clocks = <&mmsys CLK_MM_DISP_OVL0>;
> +                       interrupts = <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH 0>;
> +                       iommus = <&iommu_mm IOMMU_PORT_L0_OVL_RDMA0>;
> +                       mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0x5000 0x1000>;
> +                       power-domains = <&spm MT8186_POWER_DOMAIN_DIS>;
> +               };
> +
> +               ovl0_2l: ovl at 14006000 {

I think this should be "ovl_2l0" or "ovl_2l" instead?

> +                       compatible = "mediatek,mt8186-disp-ovl-2l",
> +                                    "mediatek,mt8192-disp-ovl-2l";
> +                       reg = <0 0x14006000 0 0x1000>;
> +                       power-domains = <&spm MT8186_POWER_DOMAIN_DIS>;
> +                       clocks = <&mmsys CLK_MM_DISP_OVL0_2L>;
> +                       interrupts = <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH 0>;
> +                       iommus = <&iommu_mm IOMMU_PORT_L1_OVL_2L_RDMA0>;
> +                       mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0x6000 0x1000>;
> +               };

Also, this patch is missing the aliases for ovl* and rdma*. Without them
the display driver doesn't properly detect the second pipeline, and only
one CRTC is generated.

ChenYu