[PATCH v3 net-next 5/5] net: wwan: t7xx: Devlink documentation
Bagas Sanjaya
bagasdotme at gmail.com
Sun Jan 8 19:48:00 PST 2023
On Fri, Jan 06, 2023 at 09:58:06PM +0530, m.chetan.kumar at linux.intel.com wrote:
> Refer to t7xx.rst file for details.
Above line is unnecessary.
> +The wwan device is put into fastboot mode via devlink reload command, by
> +passing "driver_reinit" action.
> +
> +$ devlink dev reload pci/0000:$bdf action driver_reinit
> +
> +Upon completion of fw flashing or coredump collection the wwan device is
> +reset to normal mode using devlink reload command, by passing "fw_activate"
> +action.
> +
> +$ devlink dev reload pci/0000:$bdf action fw_activate
Personally I prefer to put command-line explanations below the actual
command:
---- >8 ----
diff --git a/Documentation/networking/devlink/t7xx.rst b/Documentation/networking/devlink/t7xx.rst
index de220878ad7649..24f9e0ee69bffb 100644
--- a/Documentation/networking/devlink/t7xx.rst
+++ b/Documentation/networking/devlink/t7xx.rst
@@ -74,17 +74,21 @@ The supported list of firmware image types is described below.
procedure, fastboot command & response are exchanged between driver and wwan
device.
+::
+
+ $ devlink dev reload pci/0000:$bdf action driver_reinit
+
The wwan device is put into fastboot mode via devlink reload command, by
passing "driver_reinit" action.
-$ devlink dev reload pci/0000:$bdf action driver_reinit
+::
+
+ $ devlink dev reload pci/0000:$bdf action fw_activate
Upon completion of fw flashing or coredump collection the wwan device is
reset to normal mode using devlink reload command, by passing "fw_activate"
action.
-$ devlink dev reload pci/0000:$bdf action fw_activate
-
Flash Commands:
===============
However, I find it's odd to jump from firmware image type list directly to
devlink usage. Perhaps the latter should be put into the following section
below?
I also find that there is minor inconsistency of keyword formatting, so I
have to inline-code the uninlined remainings:
---- >8 ----
diff --git a/Documentation/networking/devlink/t7xx.rst b/Documentation/networking/devlink/t7xx.rst
index 24f9e0ee69bffb..d8feefe116c978 100644
--- a/Documentation/networking/devlink/t7xx.rst
+++ b/Documentation/networking/devlink/t7xx.rst
@@ -29,7 +29,7 @@ Flash Update
The ``t7xx`` driver implements the flash update using the ``devlink-flash``
interface.
-The driver uses DEVLINK_SUPPORT_FLASH_UPDATE_COMPONENT to identify the type of
+The driver uses ``DEVLINK_SUPPORT_FLASH_UPDATE_COMPONENT`` to identify the type of
firmware image that need to be programmed upon the request by user space application.
The supported list of firmware image types is described below.
@@ -79,14 +79,14 @@ device.
$ devlink dev reload pci/0000:$bdf action driver_reinit
The wwan device is put into fastboot mode via devlink reload command, by
-passing "driver_reinit" action.
+passing ``driver_reinit`` action.
::
$ devlink dev reload pci/0000:$bdf action fw_activate
Upon completion of fw flashing or coredump collection the wwan device is
-reset to normal mode using devlink reload command, by passing "fw_activate"
+reset to normal mode using devlink reload command, by passing ``fw_activate``
action.
Flash Commands:
> +
> +Flash Commands:
> +===============
Trim the unneeded trailing colon on the section title.
> +
> +$ devlink dev flash pci/0000:$bdf file preloader_k6880v1_mdot2_datacard.bin component "preloader"
> +
> +$ devlink dev flash pci/0000:$bdf file loader_ext-verified.img component "loader_ext1"
> +
> +$ devlink dev flash pci/0000:$bdf file tee-verified.img component "tee1"
> +
> +$ devlink dev flash pci/0000:$bdf file lk-verified.img component "lk"
> +
> +$ devlink dev flash pci/0000:$bdf file spmfw-verified.img component "spmfw"
> +
> +$ devlink dev flash pci/0000:$bdf file sspm-verified.img component "sspm_1"
> +
> +$ devlink dev flash pci/0000:$bdf file mcupm-verified.img component "mcupm_1"
> +
> +$ devlink dev flash pci/0000:$bdf file dpm-verified.img component "dpm_1"
> +
> +$ devlink dev flash pci/0000:$bdf file boot-verified.img component "boot"
> +
> +$ devlink dev flash pci/0000:$bdf file root.squashfs component "rootfs"
> +
> +$ devlink dev flash pci/0000:$bdf file modem-verified.img component "md1img"
> +
> +$ devlink dev flash pci/0000:$bdf file dsp-verified.bin component "md1dsp"
> +
> +$ devlink dev flash pci/0000:$bdf file OP_OTA.img component "mcf1"
> +
> +$ devlink dev flash pci/0000:$bdf file OEM_OTA.img component "mcf2"
> +
> +$ devlink dev flash pci/0000:$bdf file DEV_OTA.img component "mcf3"
> +
> <snipped>...
> +Region commands
> +===============
> +
> +$ devlink region show
> +
> +
> +$ devlink region new mr_dump
> +
> +$ devlink region read mr_dump snapshot 0 address 0 length $len
> +
> +$ devlink region del mr_dump snapshot 0
> +
> +$ devlink region new lk_dump
> +
> +$ devlink region read lk_dump snapshot 0 address 0 length $len
> +
> +$ devlink region del lk_dump snapshot 0
> +
> +Note: $len is actual len to be dumped.
Please briefly describe these devlink commands.
Also, wrap them in literal code blocks:
---- >8 ----
diff --git a/Documentation/networking/devlink/t7xx.rst b/Documentation/networking/devlink/t7xx.rst
index d8feefe116c978..1ba3ba4680e721 100644
--- a/Documentation/networking/devlink/t7xx.rst
+++ b/Documentation/networking/devlink/t7xx.rst
@@ -92,35 +92,65 @@ action.
Flash Commands:
===============
-$ devlink dev flash pci/0000:$bdf file preloader_k6880v1_mdot2_datacard.bin component "preloader"
+::
-$ devlink dev flash pci/0000:$bdf file loader_ext-verified.img component "loader_ext1"
+ $ devlink dev flash pci/0000:$bdf file preloader_k6880v1_mdot2_datacard.bin component "preloader"
-$ devlink dev flash pci/0000:$bdf file tee-verified.img component "tee1"
+::
-$ devlink dev flash pci/0000:$bdf file lk-verified.img component "lk"
+ $ devlink dev flash pci/0000:$bdf file loader_ext-verified.img component "loader_ext1"
-$ devlink dev flash pci/0000:$bdf file spmfw-verified.img component "spmfw"
+::
-$ devlink dev flash pci/0000:$bdf file sspm-verified.img component "sspm_1"
+ $ devlink dev flash pci/0000:$bdf file tee-verified.img component "tee1"
-$ devlink dev flash pci/0000:$bdf file mcupm-verified.img component "mcupm_1"
+::
-$ devlink dev flash pci/0000:$bdf file dpm-verified.img component "dpm_1"
+ $ devlink dev flash pci/0000:$bdf file lk-verified.img component "lk"
-$ devlink dev flash pci/0000:$bdf file boot-verified.img component "boot"
+::
-$ devlink dev flash pci/0000:$bdf file root.squashfs component "rootfs"
+ $ devlink dev flash pci/0000:$bdf file spmfw-verified.img component "spmfw"
-$ devlink dev flash pci/0000:$bdf file modem-verified.img component "md1img"
+::
-$ devlink dev flash pci/0000:$bdf file dsp-verified.bin component "md1dsp"
+ $ devlink dev flash pci/0000:$bdf file sspm-verified.img component "sspm_1"
-$ devlink dev flash pci/0000:$bdf file OP_OTA.img component "mcf1"
+::
-$ devlink dev flash pci/0000:$bdf file OEM_OTA.img component "mcf2"
+ $ devlink dev flash pci/0000:$bdf file mcupm-verified.img component "mcupm_1"
-$ devlink dev flash pci/0000:$bdf file DEV_OTA.img component "mcf3"
+::
+
+ $ devlink dev flash pci/0000:$bdf file dpm-verified.img component "dpm_1"
+
+::
+
+ $ devlink dev flash pci/0000:$bdf file boot-verified.img component "boot"
+
+::
+
+ $ devlink dev flash pci/0000:$bdf file root.squashfs component "rootfs"
+
+::
+
+ $ devlink dev flash pci/0000:$bdf file modem-verified.img component "md1img"
+
+::
+
+ $ devlink dev flash pci/0000:$bdf file dsp-verified.bin component "md1dsp"
+
+::
+
+ $ devlink dev flash pci/0000:$bdf file OP_OTA.img component "mcf1"
+
+::
+
+ $ devlink dev flash pci/0000:$bdf file OEM_OTA.img component "mcf2"
+
+::
+
+ $ devlink dev flash pci/0000:$bdf file DEV_OTA.img component "mcf3"
Note: Component selects the partition type to be programmed.
@@ -147,19 +177,31 @@ Following regions are accessed for device internal data.
Region commands
===============
-$ devlink region show
+::
+ $ devlink region show
+::
-$ devlink region new mr_dump
+ $ devlink region new mr_dump
-$ devlink region read mr_dump snapshot 0 address 0 length $len
+::
-$ devlink region del mr_dump snapshot 0
+ $ devlink region read mr_dump snapshot 0 address 0 length $len
-$ devlink region new lk_dump
+::
-$ devlink region read lk_dump snapshot 0 address 0 length $len
+ $ devlink region del mr_dump snapshot 0
-$ devlink region del lk_dump snapshot 0
+::
+
+ $ devlink region new lk_dump
+
+::
+
+ $ devlink region read lk_dump snapshot 0 address 0 length $len
+
+::
+
+ $ devlink region del lk_dump snapshot 0
Note: $len is actual len to be dumped.
Thanks.
--
An old man doll... just what I always wanted! - Clara
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 228 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-mediatek/attachments/20230109/31e22fa7/attachment-0001.sig>
More information about the Linux-mediatek
mailing list