[PATCH 3/3] arm64: dts: mediatek: enable USB device port for mt8195-demo board

[Chunfeng Yun (云春峰)]

On Wed, 2023-02-01 at 13:24 +0100, Matthias Brugger wrote:
> 
> On 05/01/2023 10:28, Macpaul Lin wrote:
> > 1. Enable USB device port (USB port0).
> > 2. Enable u2 speed for other USB HOST (USB port1/2/3).
> > 3. Configure mt6360 (TYPEC) related pinctrls.
> > 
> > Note: Full dual-role switch capability requires TYPEC MUX driver
> > and dts
> > update will be send in separate patches.
> > 
> > Signed-off-by: Macpaul Lin <macpaul.lin at mediatek.com>
> > ---
> >   arch/arm64/boot/dts/mediatek/mt8195-demo.dts | 51
> > ++++++++++++++++++++
> >   1 file changed, 51 insertions(+)
> > 
> > diff --git a/arch/arm64/boot/dts/mediatek/mt8195-demo.dts
> > b/arch/arm64/boot/dts/mediatek/mt8195-demo.dts
> > index 07a864cb8b54..207bb5f4c58f 100644
> > --- a/arch/arm64/boot/dts/mediatek/mt8195-demo.dts
> > +++ b/arch/arm64/boot/dts/mediatek/mt8195-demo.dts
> > @@ -12,6 +12,7 @@
> >   #include <dt-bindings/input/input.h>
> >   #include <dt-bindings/pinctrl/mt8195-pinfunc.h>
> >   #include <dt-bindings/regulator/mediatek,mt6360-regulator.h>
> > +#include <dt-bindings/usb/pd.h>
> >   
> >   / {
> >   	model = "MediaTek MT8195 demo board";
> > @@ -380,6 +381,22 @@
> >   		};
> >   	};
> >   
> > +	mt6360_pins: mt6360-pins {
> > +		pins {
> > +			pinmux = <PINMUX_GPIO100__FUNC_GPIO100>,
> > +				 <PINMUX_GPIO101__FUNC_GPIO101>;
> > +			input-enable;
> > +			bias-pull-up;
> > +		};
> > +	};
> > +
> > +	u3_p0_vbus: u3_p0vbusdefault {
> > +		pins_cmd_dat {
> > +			pinmux = <PINMUX_GPIO63__FUNC_VBUSVALID>;
> > +			input-enable;
> > +		};
> > +	};
> > +
> >   	uart0_pins: uart0-pins {
> >   		pins {
> >   			pinmux = <PINMUX_GPIO98__FUNC_UTXD0>,
> > @@ -393,6 +410,14 @@
> >   				 <PINMUX_GPIO103__FUNC_URXD1>;
> >   		};
> >   	};
> > +
> > +	usb_otg_vbus: usb-otg-vbus-regulator {
> > +		compatible = "regulator-fixed";
> > +		regulator-name = "otg-vbus";
> > +		regulator-min-microvolt = <5000000>;
> > +		regulator-max-microvolt = <5000000>;
> > +		enable-active-high;
> > +	};
> >   };
> >   
> >   
> > @@ -412,6 +437,22 @@
> >   	status = "okay";
> >   };
> >   
> > +&u3port0 {
> > +	status = "okay";
> > +};
> > +
> > +&u2port1 {
> > +	status = "okay";
> > +};
> > +
> > +&u2port2 {
> > +	status = "okay";
> > +};
> > +
> > +&u2port3 {
> > +	status = "okay";
> > +};
> > +
> >   &u3phy0 {
> >   	status = "okay";
> >   };
> > @@ -428,6 +469,16 @@
> >   	status = "okay";
> >   };
> >   
> > +&ssusb {
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&u3_p0_vbus>;
> > +	vusb33-supply = <&mt6359_vusb_ldo_reg>;
> > +	dr_mode = "otg";
> > +	mediatek,usb3-drd;
> 
> What it that used for?
> git grep didn't gave me any hit.
"mediatek,usb3-drd;" can be now removed,

the patch sent out on Jul 8 2022:
"683ff6e485f1 usb: mtu3: check capability of usb3 dual role"
already removed the property.

Thanks a lot

> 
> Regards,
> Matthias
> 
> > +	usb-role-switch;
> > +	status = "okay";
> > +};
> > +
> >   &xhci0 {
> >   	vusb33-supply = <&mt6359_vusb_ldo_reg>;
> >   	vbus-supply = <&otg_vbus_regulator>;