[PATCH 9/9] net: dsa: mt7530: use external PCS driver

Vladimir Oltean olteanv at gmail.com
Fri Feb 3 14:19:15 PST 2023


On Fri, Feb 03, 2023 at 07:06:53AM +0000, Daniel Golle wrote:
> @@ -2728,11 +2612,14 @@ mt753x_phylink_mac_select_pcs(struct dsa_switch *ds, int port,
>  
>  	switch (interface) {
>  	case PHY_INTERFACE_MODE_TRGMII:
> +		return &priv->pcs[port].pcs;
>  	case PHY_INTERFACE_MODE_SGMII:
>  	case PHY_INTERFACE_MODE_1000BASEX:
>  	case PHY_INTERFACE_MODE_2500BASEX:
> -		return &priv->pcs[port].pcs;
> +		if (!mt753x_is_mac_port(port))
> +			return ERR_PTR(-EINVAL);

What is the reason for returning ERR_PTR(-EINVAL) to mac_select_pcs()?

>  
> +		return priv->sgmii_pcs[port - 5];

How about putting the pcs pointer in struct mt7530_port?

>  	default:
>  		return NULL;
>  	}
> @@ -3088,8 +2934,6 @@ mt753x_setup(struct dsa_switch *ds)
>  		priv->pcs[i].pcs.ops = priv->info->pcs_ops;
>  		priv->pcs[i].priv = priv;
>  		priv->pcs[i].port = i;
> -		if (mt753x_is_mac_port(i))
> -			priv->pcs[i].pcs.poll = 1;
>  	}
>  
>  	ret = priv->info->sw_setup(ds);
> @@ -3104,6 +2948,15 @@ mt753x_setup(struct dsa_switch *ds)
>  	if (ret && priv->irq)
>  		mt7530_free_irq_common(priv);

You need to patch the previous code to "return ret".

>  
> +	if (priv->id == ID_MT7531)

if the code block below is multi-line (which it is), put braces here too

or can return early if priv->id != ID_MT7531, and this reduces the
indentation by one level.

> +		for (i = 0; i < 2; ++i) {

could also iterate over all ports and ignore those which have
!mt753x_is_mac_port(port)

> +			regmap = devm_regmap_init(ds->dev,
> +						  &mt7531_regmap_bus, priv,
> +						  &mt7531_pcs_config[i]);

can fail

> +			priv->sgmii_pcs[i] = mtk_pcs_create(ds->dev, regmap,
> +							    0x128, 0);

can fail

Don't forget to do error teardown which isn't leaky

0x128 comes from the old definition of MT7531_PHYA_CTRL_SIGNAL3(port),
so please keep a macro of some sorts to denote the offset of ana_rgc3
for MT7531, rather than just this obscure magic number.

> +		}
> +
>  	return ret;
>  }
>  
> @@ -3199,7 +3052,7 @@ static const struct mt753x_info mt753x_table[] = {
>  	},
>  	[ID_MT7531] = {
>  		.id = ID_MT7531,
> -		.pcs_ops = &mt7531_pcs_ops,
> +		.pcs_ops = &mt7530_pcs_ops,
>  		.sw_setup = mt7531_setup,
>  		.phy_read_c22 = mt7531_ind_c22_phy_read,
>  		.phy_write_c22 = mt7531_ind_c22_phy_write,
> @@ -3309,7 +3162,7 @@ static void
>  mt7530_remove(struct mdio_device *mdiodev)
>  {
>  	struct mt7530_priv *priv = dev_get_drvdata(&mdiodev->dev);
> -	int ret = 0;
> +	int ret = 0, i;
>  
>  	if (!priv)
>  		return;
> @@ -3328,6 +3181,11 @@ mt7530_remove(struct mdio_device *mdiodev)
>  		mt7530_free_irq(priv);
>  
>  	dsa_unregister_switch(priv->ds);
> +
> +	for (i = 0; i < 2; ++i)

There is no ++i in this driver and there are 11 i++, so please be
consistent with what exists.

> +		if (priv->sgmii_pcs[i])
> +			mtk_pcs_destroy(priv->sgmii_pcs[i]);
> +
>  	mutex_destroy(&priv->reg_mutex);
>  }
>  



More information about the Linux-mediatek mailing list