[PATCH 1/1] Bluetooth: btusb: mediatek: add a recovery method for MT7922
Sean Wang
sean.wang at kernel.org
Mon Dec 18 16:29:52 PST 2023
Hi Hao,
On Fri, Dec 15, 2023 at 12:40 AM Hao Qin <hao.qin at mediatek.com> wrote:
>
> From: "hao.qin" <hao.qin at mediatek.com>
>
> For MT7922, perform a reset before patch download to avoid
> unexpected problems caused by inconsistency between upper layer
> status and dongle status. Add USB reset retry to recover from
> unexpected patch download failure.
After looking through the patch, I guess the patch providing the reset
mechanism for
1) the core layer to call when cmd is timeout
2) resetting the device before the patch download
3) handling situations where something goes wrong during the patch
download phase
right ? if so, the description should be revised to make the patch
close to what it does
>
> Signed-off-by: hao.qin <hao.qin at mediatek.com>
> ---
> drivers/bluetooth/btusb.c | 66 +++++++++++++++++++++++++++------------
> 1 file changed, 46 insertions(+), 20 deletions(-)
>
> diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
> index 0926e4451802..778e1a0d9cae 100644
> --- a/drivers/bluetooth/btusb.c
> +++ b/drivers/bluetooth/btusb.c
> @@ -2812,7 +2812,7 @@ static int btusb_mtk_hci_wmt_sync(struct hci_dev *hdev,
> * WMT command.
> */
> err = wait_on_bit_timeout(&data->flags, BTUSB_TX_WAIT_VND_EVT,
> - TASK_INTERRUPTIBLE, HCI_INIT_TIMEOUT);
> + TASK_INTERRUPTIBLE, HCI_CMD_TIMEOUT);
The changes are not specific to MT7922 and do not align with the
commit description. Kindly consider moving them to another patch and
provide clear reasons why they are necessary for MT7922 or any other
chipsets.
> if (err == -EINTR) {
> bt_dev_err(hdev, "Execution of wmt command interrupted");
> clear_bit(BTUSB_TX_WAIT_VND_EVT, &data->flags);
> @@ -2994,28 +2994,22 @@ static u32 btusb_mtk_reset_done(struct hci_dev *hdev)
> return val & MTK_BT_RST_DONE;
> }
>
> -static int btusb_mtk_reset(struct hci_dev *hdev, void *rst_data)
> +static int btusb_mtk_subsys_reset(struct hci_dev *hdev, u32 dev_id)
> {
> struct btusb_data *data = hci_get_drvdata(hdev);
> - struct btmediatek_data *mediatek;
> u32 val;
> int err;
>
> - /* It's MediaTek specific bluetooth reset mechanism via USB */
> - if (test_and_set_bit(BTUSB_HW_RESET_ACTIVE, &data->flags)) {
> - bt_dev_err(hdev, "last reset failed? Not resetting again");
> - return -EBUSY;
> - }
> -
> - err = usb_autopm_get_interface(data->intf);
> - if (err < 0)
> - return err;
> -
> - btusb_stop_traffic(data);
> - usb_kill_anchored_urbs(&data->tx_anchor);
> - mediatek = hci_get_priv(hdev);
> -
It seems that you refactored the existing btusb_mtk_reset in the
patch. Could you please create another patch specifically for the
refactoring without introducing any functional changes of MT7922 prior
to adding the patch? This way would be good for ease of review and
tracking in the future. Additionally, it ensures that those working on
MT7921 are aware of the patch and its modifications.
> - if (mediatek->dev_id == 0x7925) {
> + if (dev_id == 0x7922) {
> + btusb_mtk_uhw_reg_read(data, MTK_BT_SUBSYS_RST, &val);
> + val |= 0x00002020;
> + btusb_mtk_uhw_reg_write(data, MTK_BT_SUBSYS_RST, val);
> + btusb_mtk_uhw_reg_write(data, MTK_EP_RST_OPT, 0x00010001);
> + btusb_mtk_uhw_reg_read(data, MTK_BT_SUBSYS_RST, &val);
> + val |= (1 << 0);
We can utilize BIT(0) instead of 1 << 0
> + btusb_mtk_uhw_reg_write(data, MTK_BT_SUBSYS_RST, val);
> + msleep(100);
> + } else if (dev_id == 0x7925) {
> btusb_mtk_uhw_reg_read(data, MTK_BT_RESET_REG_CONNV3, &val);
> val |= (1 << 5);
We can utilize BIT(5) instead of 1 << 5
> btusb_mtk_uhw_reg_write(data, MTK_BT_RESET_REG_CONNV3, val);
> @@ -3053,14 +3047,41 @@ static int btusb_mtk_reset(struct hci_dev *hdev, void *rst_data)
> err = readx_poll_timeout(btusb_mtk_reset_done, hdev, val,
> val & MTK_BT_RST_DONE, 20000, 1000000);
> if (err < 0)
> - bt_dev_err(hdev, "Reset timeout");
> + bt_dev_err(hdev, "Subsys reset timeout");
I guess it would be better to avoid the unnecessary change unrelated
to the patch.
> +
> + if (dev_id == 0x7922)
> + btusb_mtk_uhw_reg_write(data, MTK_UDMA_INT_STA_BT, 0x000000FF);
>
> btusb_mtk_id_get(data, 0x70010200, &val);
> if (!val)
> bt_dev_err(hdev, "Can't get device id, subsys reset fail.");
>
> - usb_queue_reset_device(data->intf);
> + return err;
> +}
> +
> +static int btusb_mtk_reset(struct hci_dev *hdev, void *rst_data)
> +{
> + struct btusb_data *data = hci_get_drvdata(hdev);
> + struct btmediatek_data *mediatek;
> + int err;
> +
> + /* It's MediaTek specific bluetooth reset mechanism via USB */
> + if (test_and_set_bit(BTUSB_HW_RESET_ACTIVE, &data->flags)) {
> + bt_dev_err(hdev, "last reset failed? Not resetting again");
> + return -EBUSY;
> + }
> +
> + err = usb_autopm_get_interface(data->intf);
> + if (err < 0)
> + return err;
> +
> + btusb_stop_traffic(data);
> + usb_kill_anchored_urbs(&data->tx_anchor);
> + mediatek = hci_get_priv(hdev);
>
> + err = btusb_mtk_subsys_reset(hdev, mediatek->dev_id);
> +
> + usb_queue_reset_device(data->intf);
> clear_bit(BTUSB_HW_RESET_ACTIVE, &data->flags);
>
> return err;
> @@ -3119,6 +3140,8 @@ static int btusb_mtk_setup(struct hci_dev *hdev)
> fwname = FIRMWARE_MT7668;
> break;
> case 0x7922:
> + btusb_mtk_subsys_reset(hdev, dev_id);
> + fallthrough;
> case 0x7961:
> case 0x7925:
> if (dev_id == 0x7925)
> @@ -3134,6 +3157,9 @@ static int btusb_mtk_setup(struct hci_dev *hdev)
> btusb_mtk_hci_wmt_sync);
> if (err < 0) {
> bt_dev_err(hdev, "Failed to set up firmware (%d)", err);
> + btusb_stop_traffic(data);
> + usb_kill_anchored_urbs(&data->tx_anchor);
> + usb_queue_reset_device(data->intf);
The change doesn't appear to be specific to MT7922, as the commit
description suggests. Please consider splitting it into another patch
to address any existing chipset issues, if necessary.
> return err;
> }
>
> --
> 2.18.0
>
>
More information about the Linux-mediatek
mailing list