[PATCH net-next 01/15] net: dsa: mt7530: always trap frames to active CPU port on MT7530
Vladimir Oltean
olteanv at gmail.com
Thu Dec 7 09:48:29 PST 2023
On Sat, Dec 02, 2023 at 11:29:18AM +0300, Arınç ÜNAL wrote:
> > I would be tempted to write this as:
> >
> > mask = BIT(cpu_dp->index);
> >
> > if (operational)
> > priv->active_cpu_ports |= mask;
> > else
> > priv->active_cpu_ports &= ~mask;
> >
> > Now, what happens when active_cpu_ports is zero? Doesn't that mean there
> > is no active CPU port? In which case, wouldn't disabling the CPU port
> > direction be appropriate, such as:
> >
> > if (priv->active_cpu_ports)
> > val = CPU_EN | CPU_PORT(__ffs(priv->active_cpu_ports));
> > else
> > val = 0;
> >
> > mt7530_rmw(priv, MT7530_MFC, CPU_EN | CPU_PORT_MASK, val);
> >
> > ?
>
> In practice, it doesn't seem to matter. The CPU_EN bit enables the CPU port
> defined on CPU_PORT_MASK which is used for trapping frames. No active CPU
> ports would mean that all the DSA conduits are down. In that case, all the
> user ports will be down also. So there won't be any traffic. But disabling
> it is of course more appropriate here.
Ack, DSA takes down the user ports which are affine to a certain conduit
interface when that goes down. See the NETDEV_GOING_DOWN handling in
net/dsa/user.c.
> >
> > > struct mt7530_priv {
> > > struct device *dev;
> > > @@ -786,6 +787,7 @@ struct mt7530_priv {
> > > struct irq_domain *irq_domain;
> > > u32 irq_enable;
> > > int (*create_sgmii)(struct mt7530_priv *priv, bool dual_sgmii);
> > > + unsigned long active_cpu_ports;
> >
> > So this will be 32 or 64 bit in size. Presumably you know how many CPU
> > ports there can be, which looking at this code must be less than 8 as
> > CPU_PORT_MASK is only 3 bits in size. So, maybe use a u8, and check
> > that cpu_dp->index <= 7 ?
We picked "unsigned long" as storage because that's also the size of the
argument that __ffs() takes. But admittedly, we could have also stored a
smaller variable and promote it to unsigned long when we pass it to __ffs().
> Aren't there other mechanisms to check that cpu_dp->index is a valid port?
cpu_dp->index is guaranteed by DSA to be valid (according to the "reg"
value from the device tree and smaller than ds->num_ports). It's just a
question of balancing this kind of optimization with the possibility
that a future switch appears which has more than MT7530_NUM_PORTS (7) ports.
> At least with phylink_get_caps(), only ports lower than 7 will have proper
> interface modes allowed.
>
> Here's the code after you and Vladimir's review:
>
> static void
> mt753x_conduit_state_change(struct dsa_switch *ds,
> const struct net_device *conduit,
> bool operational)
> {
> struct dsa_port *cpu_dp = conduit->dsa_ptr;
> struct mt7530_priv *priv = ds->priv;
> u8 mask;
> int val;
>
> /* Set the CPU port to trap frames to for MT7530. Trapped frames will be
> * forwarded to the numerically smallest CPU port which the DSA conduit
> * interface its affine to is up.
> */
> if (priv->id != ID_MT7530 && priv->id != ID_MT7621)
> return;
>
> mask = BIT(cpu_dp->index);
>
> if (operational)
> priv->active_cpu_ports |= mask;
> else
> priv->active_cpu_ports &= ~mask;
>
> if (priv->active_cpu_ports)
> val = CPU_EN | CPU_PORT(__ffs(priv->active_cpu_ports));
> else
> val = 0;
You could initialize "val" with 0 at declaration time and you wouldn't
need the "else" branch.
>
> mt7530_rmw(priv, MT7530_MFC, CPU_EN | CPU_PORT_MASK, val);
> }
>
> struct mt7530_priv {
> [...]
> u8 active_cpu_ports;
> };
Actually, looking at the code now, I don't understand why we even keep
track of the active_cpu_ports mask in the driver. We could read the
MT7530_MFC register in mt753x_conduit_state_change(), flip the bit
corresponding just to cpu_dp->index (rather than rmw all of CPU_PORT_MASK),
and write back the result. And to address Russell's concern, we could test
whether the resulting CPU_PORT_MASK portion of what we're going to write
back is all-zeroes or not, and if it is, clear the CPU_EN bit, otherwise
set it.
>
> >
> > I would also suggest moving irq_enable after create_sgmii, to avoid
> > holes in the struct.
>
> Sorry, I've got no idea about this. Could you explain why would there
> possibly be holes in the struct with the current ordering of the members of
> the mt7530_priv structure?
>
> Arınç
FWIW:
$ pahole -C mt7530_priv $KBUILD_OUTPUT/drivers/net/dsa/mt7530.o
struct mt7530_priv {
struct device * dev; /* 0 8 */
struct dsa_switch * ds; /* 8 8 */
struct mii_bus * bus; /* 16 8 */
struct regmap * regmap; /* 24 8 */
struct reset_control * rstc; /* 32 8 */
struct regulator * core_pwr; /* 40 8 */
struct regulator * io_pwr; /* 48 8 */
struct gpio_desc * reset; /* 56 8 */
/* --- cacheline 1 boundary (64 bytes) --- */
const struct mt753x_info * info; /* 64 8 */
unsigned int id; /* 72 4 */
bool mcm; /* 76 1 */
/* XXX 3 bytes hole, try to pack */
phy_interface_t p6_interface; /* 80 4 */
phy_interface_t p5_interface; /* 84 4 */
unsigned int p5_intf_sel; /* 88 4 */
u8 mirror_rx; /* 92 1 */
u8 mirror_tx; /* 93 1 */
/* XXX 2 bytes hole, try to pack */
struct mt7530_port ports[7]; /* 96 168 */
/* --- cacheline 4 boundary (256 bytes) was 8 bytes ago --- */
struct mt753x_pcs pcs[7]; /* 264 280 */
/* --- cacheline 8 boundary (512 bytes) was 32 bytes ago --- */
struct mutex reg_mutex; /* 544 32 */
/* --- cacheline 9 boundary (576 bytes) --- */
int irq; /* 576 4 */
/* XXX 4 bytes hole, try to pack */
struct irq_domain * irq_domain; /* 584 8 */
u32 irq_enable; /* 592 4 */
/* XXX 4 bytes hole, try to pack */
int (*create_sgmii)(struct mt7530_priv *, bool); /* 600 8 */
unsigned long active_cpu_ports; /* 608 8 */
/* size: 616, cachelines: 10, members: 24 */
/* sum members: 603, holes: 4, sum holes: 13 */
/* last cacheline: 40 bytes */
};
It's not like this makes any practical difference, as struct mt7530_priv
isn't used from hot paths, but tidying it up is a good sign of clean,
careful development, and of understanding memory alignment.
More information about the Linux-mediatek
mailing list