[RFC PATCH net-next 14/22] net: dsa: mt7530: switch to if/else statements on mt7530_setup_port6()

[arinc9.unal at gmail.com]

From: Arınç ÜNAL <arinc.unal at arinc9.com>

This code is from before this driver was converted to phylink API. Phylink
deals with the unsupported interface cases before mt7530_setup_port6() is
run. Therefore, the default case would never run. However, it must be
defined nonetheless to handle all the remaining enumeration values, the
phy-modes.

Switch to if/else statements which simplifies the code.

Change mt7530_setup_port6() to void now that there're no error cases left.

Tested-by: Arınç ÜNAL <arinc.unal at arinc9.com>
Signed-off-by: Arınç ÜNAL <arinc.unal at arinc9.com>
---
 drivers/net/dsa/mt7530.c | 35 +++++++++++------------------------
 1 file changed, 11 insertions(+), 24 deletions(-)

diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 8fe9b1e6932c..610828b56eac 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -400,11 +400,11 @@ static void mt7530_pll_setup(struct mt7530_priv *priv)
 }
 
 /* Setup port 6 interface mode and TRGMII TX circuit */
-static int
+static void
 mt7530_setup_port6(struct dsa_switch *ds, phy_interface_t interface)
 {
 	struct mt7530_priv *priv = ds->priv;
-	u32 ncpo1, ssc_delta, trgint, xtal, val;
+	u32 ncpo1, ssc_delta, xtal, val;
 
 	val = mt7530_read(priv, MT7530_MHWTRAP);
 	val &= ~MHWTRAP_P6_DIS;
@@ -412,16 +412,18 @@ mt7530_setup_port6(struct dsa_switch *ds, phy_interface_t interface)
 
 	xtal = mt7530_read(priv, MT7530_HWTRAP) & HWTRAP_XTAL_MASK;
 
-	switch (interface) {
-	case PHY_INTERFACE_MODE_RGMII:
-		trgint = 0;
-		break;
-	case PHY_INTERFACE_MODE_TRGMII:
-		trgint = 1;
+	if (interface == PHY_INTERFACE_MODE_RGMII) {
+		mt7530_rmw(priv, MT7530_P6ECR, P6_INTF_MODE_MASK,
+			   P6_INTF_MODE(0));
+	} else {
+		mt7530_rmw(priv, MT7530_P6ECR, P6_INTF_MODE_MASK,
+			   P6_INTF_MODE(1));
+
 		if (xtal == HWTRAP_XTAL_25MHZ)
 			ssc_delta = 0x57;
 		else
 			ssc_delta = 0x87;
+
 		if (priv->id == ID_MT7621) {
 			/* PLL frequency: 150MHz: 1.2GBit */
 			if (xtal == HWTRAP_XTAL_40MHZ)
@@ -434,17 +436,7 @@ mt7530_setup_port6(struct dsa_switch *ds, phy_interface_t interface)
 			if (xtal == HWTRAP_XTAL_25MHZ)
 				ncpo1 = 0x1400;
 		}
-		break;
-	default:
-		dev_err(priv->dev, "xMII interface %d not supported\n",
-			interface);
-		return -EINVAL;
-	}
 
-	mt7530_rmw(priv, MT7530_P6ECR, P6_INTF_MODE_MASK,
-		   P6_INTF_MODE(trgint));
-
-	if (trgint) {
 		/* Disable the MT7530 TRGMII clocks */
 		core_clear(priv, CORE_TRGMII_GSW_CLK_CG, REG_TRGMIICK_EN);
 
@@ -466,8 +458,6 @@ mt7530_setup_port6(struct dsa_switch *ds, phy_interface_t interface)
 		/* Enable the MT7530 TRGMII clocks */
 		core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_TRGMIICK_EN);
 	}
-
-	return 0;
 }
 
 static void
@@ -2568,14 +2558,11 @@ mt7530_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
 		  phy_interface_t interface)
 {
 	struct mt7530_priv *priv = ds->priv;
-	int ret;
 
 	if (port == 5) {
 		mt7530_setup_port5(priv->ds, interface);
 	} else if (port == 6) {
-		ret = mt7530_setup_port6(priv->ds, interface);
-		if (ret)
-			return ret;
+		mt7530_setup_port6(priv->ds, interface);
 	}
 
 	return 0;
-- 
2.37.2