[PATCH v7, 1/3] mailbox: mtk-cmdq: add gce software ddr enable private data

Matthias Brugger matthias.bgg at gmail.com
Fri Sep 30 06:20:29 PDT 2022



On 30/09/2022 11:59, Yongqiang Niu wrote:
> if gce work control by software, we need set software enable
> for MT8186 Soc
> 
> there is a handshake flow between gce and ddr hardware,
> if not set ddr enable flag of gce, ddr will fall into idle
> mode, then gce instructions will not process done.
> we need set this flag of gce to tell ddr when gce is idle or busy
> controlled by software flow.
> 
> Signed-off-by: Yongqiang Niu <yongqiang.niu at mediatek.com>
> ---
>   drivers/mailbox/mtk-cmdq-mailbox.c | 11 ++++++++++-
>   1 file changed, 10 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/mailbox/mtk-cmdq-mailbox.c b/drivers/mailbox/mtk-cmdq-mailbox.c
> index 9465f9081515..04eb44d89119 100644
> --- a/drivers/mailbox/mtk-cmdq-mailbox.c
> +++ b/drivers/mailbox/mtk-cmdq-mailbox.c
> @@ -38,6 +38,8 @@
>   #define CMDQ_THR_PRIORITY		0x40
>   
>   #define GCE_GCTL_VALUE			0x48
> +#define GCE_CTRL_BY_SW				GENMASK(2, 0)
> +#define GCE_DDR_EN				GENMASK(18, 16)
>   
>   #define CMDQ_THR_ACTIVE_SLOT_CYCLES	0x3200
>   #define CMDQ_THR_ENABLED		0x1
> @@ -80,6 +82,7 @@ struct cmdq {
>   	bool			suspended;
>   	u8			shift_pa;
>   	bool			control_by_sw;
> +	bool			sw_ddr_en;
>   	u32			gce_num;
>   };
>   
> @@ -87,6 +90,7 @@ struct gce_plat {
>   	u32 thread_nr;
>   	u8 shift;
>   	bool control_by_sw;
> +	bool sw_ddr_en;
>   	u32 gce_num;
>   };
>   
> @@ -129,7 +133,11 @@ static void cmdq_init(struct cmdq *cmdq)
>   
>   	WARN_ON(clk_bulk_enable(cmdq->gce_num, cmdq->clocks));
>   	if (cmdq->control_by_sw)
> -		writel(0x7, cmdq->base + GCE_GCTL_VALUE);
> +		writel(GCE_CTRL_BY_SW, cmdq->base + GCE_GCTL_VALUE);

Thanks for doing this, but I think this should be part of a seperate patch. It's 
a cleanup and has nothing to do with the new sw_ddr_en, correct?

Regards,
Matthias

> +
> +	if (cmdq->sw_ddr_en)
> +		writel(GCE_DDR_EN | GCE_CTRL_BY_SW, cmdq->base + GCE_GCTL_VALUE);
> +
>   	writel(CMDQ_THR_ACTIVE_SLOT_CYCLES, cmdq->base + CMDQ_THR_SLOT_CYCLES);
>   	for (i = 0; i <= CMDQ_MAX_EVENT; i++)
>   		writel(i, cmdq->base + CMDQ_SYNC_TOKEN_UPDATE);
> @@ -543,6 +551,7 @@ static int cmdq_probe(struct platform_device *pdev)
>   	cmdq->thread_nr = plat_data->thread_nr;
>   	cmdq->shift_pa = plat_data->shift;
>   	cmdq->control_by_sw = plat_data->control_by_sw;
> +	cmdq->sw_ddr_en = plat_data->sw_ddr_en;
>   	cmdq->gce_num = plat_data->gce_num;
>   	cmdq->irq_mask = GENMASK(cmdq->thread_nr - 1, 0);
>   	err = devm_request_irq(dev, cmdq->irq, cmdq_irq_handler, IRQF_SHARED,



More information about the Linux-mediatek mailing list