[PATCH] spi: Replace `dummy.nbytes` with `dummy.ncycles`

Serge Semin fancer.lancer at gmail.com
Sun Sep 25 15:03:04 PDT 2022


Hello Sergiu

On Sun, Sep 11, 2022 at 08:45:53PM +0300, Sergiu Moga wrote:
> In order to properly represent the hardware functionality
> in the core, avoid reconverting the number of dummy cycles
> to the number of bytes and only work with the former.
> Instead, let the drivers that do need this conversion do
> it themselves.
> 
> Signed-off-by: Sergiu Moga <sergiu.moga at microchip.com>
> ---
>  drivers/mtd/spi-nor/core.c        | 22 ++++----------

[...]

>  drivers/spi/spi-dw-core.c         | 10 +++++--

[...]

>  drivers/spi/spi-mem.c             | 27 +++++++++++------

[...]

>  drivers/spi/spi-mtk-nor.c         | 48 +++++++++++++++++--------------

[...]

>  drivers/spi/spi-zynq-qspi.c       | 15 ++++++----
>  drivers/spi/spi-zynqmp-gqspi.c    |  8 ++++--
>  include/linux/spi/spi-mem.h       | 10 +++----
>  25 files changed, 234 insertions(+), 147 deletions(-)
> 
> diff --git a/drivers/mtd/spi-nor/core.c b/drivers/mtd/spi-nor/core.c
> index f2c64006f8d7..cc8ca824f912 100644
> --- a/drivers/mtd/spi-nor/core.c
> +++ b/drivers/mtd/spi-nor/core.c
> @@ -88,7 +88,7 @@ void spi_nor_spimem_setup_op(const struct spi_nor *nor,
>  	if (op->addr.nbytes)
>  		op->addr.buswidth = spi_nor_get_protocol_addr_nbits(proto);
>  



> -	if (op->dummy.nbytes)
> +	if (op->dummy.ncycles)
>  		op->dummy.buswidth = spi_nor_get_protocol_addr_nbits(proto);
>  
>  	if (op->data.nbytes)
> @@ -106,9 +106,6 @@ void spi_nor_spimem_setup_op(const struct spi_nor *nor,
>  		op->dummy.dtr = true;
>  		op->data.dtr = true;
>  
> -		/* 2 bytes per clock cycle in DTR mode. */
> -		op->dummy.nbytes *= 2;
> -
>  		ext = spi_nor_get_cmd_ext(nor, op);
>  		op->cmd.opcode = (op->cmd.opcode << 8) | ext;
>  		op->cmd.nbytes = 2;
> @@ -207,10 +204,7 @@ static ssize_t spi_nor_spimem_read_data(struct spi_nor *nor, loff_t from,
>  
>  	spi_nor_spimem_setup_op(nor, &op, nor->read_proto);
>  
> -	/* convert the dummy cycles to the number of bytes */
> -	op.dummy.nbytes = (nor->read_dummy * op.dummy.buswidth) / 8;
> -	if (spi_nor_protocol_is_dtr(nor->read_proto))
> -		op.dummy.nbytes *= 2;
> +	op.dummy.ncycles = nor->read_dummy;

So according to this modification and what is done in the rest of the
patch, the dummy part of the SPI-mem operations now contains the number
of cycles only. Am I right to think that it means a number of dummy
clock oscillations? (Judging from what I've seen in the HW-manuals of
the SPI NOR memory devices most likely I am...) If so the "ncycles" field
is now free from the "data" semantic. Then what is the meaning of the
"buswidth and "dtr" fields in the spi_mem_op.dummy field?

>  
>  	usebouncebuf = spi_nor_spimem_bounce(nor, &op);
>  
> @@ -455,7 +449,7 @@ int spi_nor_read_sr(struct spi_nor *nor, u8 *sr)
>  
>  		if (nor->reg_proto == SNOR_PROTO_8_8_8_DTR) {
>  			op.addr.nbytes = nor->params->rdsr_addr_nbytes;
> -			op.dummy.nbytes = nor->params->rdsr_dummy;
> +			op.dummy.ncycles = nor->params->rdsr_dummy;
>  			/*
>  			 * We don't want to read only one byte in DTR mode. So,
>  			 * read 2 and then discard the second byte.
> @@ -1913,10 +1907,7 @@ static int spi_nor_spimem_check_readop(struct spi_nor *nor,
>  
>  	spi_nor_spimem_setup_op(nor, &op, read->proto);
>  
> -	/* convert the dummy cycles to the number of bytes */
> -	op.dummy.nbytes = (nor->read_dummy * op.dummy.buswidth) / 8;
> -	if (spi_nor_protocol_is_dtr(nor->read_proto))
> -		op.dummy.nbytes *= 2;
> +	op.dummy.ncycles = nor->read_dummy;
>  
>  	return spi_nor_spimem_check_op(nor, &op);
>  }
> @@ -3034,10 +3025,7 @@ static int spi_nor_create_read_dirmap(struct spi_nor *nor)
>  
>  	spi_nor_spimem_setup_op(nor, op, nor->read_proto);
>  
> -	/* convert the dummy cycles to the number of bytes */
> -	op->dummy.nbytes = (nor->read_dummy * op->dummy.buswidth) / 8;
> -	if (spi_nor_protocol_is_dtr(nor->read_proto))
> -		op->dummy.nbytes *= 2;
> +	op->dummy.ncycles = nor->read_dummy;
>  
>  	/*
>  	 * Since spi_nor_spimem_setup_op() only sets buswidth when the number

[...]

> diff --git a/drivers/spi/spi-dw-core.c b/drivers/spi/spi-dw-core.c
> index f87d97ccd2d6..0ba5c7d0e66e 100644
> --- a/drivers/spi/spi-dw-core.c
> +++ b/drivers/spi/spi-dw-core.c
> @@ -498,13 +498,17 @@ static bool dw_spi_supports_mem_op(struct spi_mem *mem,
>  static int dw_spi_init_mem_buf(struct dw_spi *dws, const struct spi_mem_op *op)
>  {
>  	unsigned int i, j, len;
> -	u8 *out;
> +	u8 *out, dummy_nbytes;
>  
>  	/*
>  	 * Calculate the total length of the EEPROM command transfer and
>  	 * either use the pre-allocated buffer or create a temporary one.
>  	 */
> -	len = op->cmd.nbytes + op->addr.nbytes + op->dummy.nbytes;

> +	dummy_nbytes = (op->dummy.ncycles * op->dummy.buswidth) / 8;

1. What about using the BITS_PER_BYTE macro (linux/bits.h) here? Since
you are adding a similar modification to so many drivers what about using
that macro there too?

2. buswidth is supposed to be always 1 in this driver (see the
dw_spi_supports_mem_op() method). So it can be dropped from the
statement above.

3. Since the ncycles now contains a number of clock cycles there is no
point in taking the SPI bus-width into account at all. What is
meaningful is how many oscillations are supposed to be placed on the
CLK line before the data is available. So the op->dummy.ncycles /
BITS_PER_BYTE statement would be more appropriate here in any case.

> +	if (op->dummy.dtr)
> +		dummy_nbytes *= 2;

DTR is unsupported by the controller. See, no spi_controller_mem_caps
initialized. So this part is redundant. The same is most likely
applicable for some of the DTR-related updates in this patch too
since the spi_controller_mem_caps structure is initialized in a few
drivers only.

> +
> +	len = op->cmd.nbytes + op->addr.nbytes + dummy_nbytes;
>  	if (op->data.dir == SPI_MEM_DATA_OUT)
>  		len += op->data.nbytes;
>  
> @@ -525,7 +529,7 @@ static int dw_spi_init_mem_buf(struct dw_spi *dws, const struct spi_mem_op *op)
>  		out[i] = DW_SPI_GET_BYTE(op->cmd.opcode, op->cmd.nbytes - i - 1);
>  	for (j = 0; j < op->addr.nbytes; ++i, ++j)
>  		out[i] = DW_SPI_GET_BYTE(op->addr.val, op->addr.nbytes - j - 1);
> -	for (j = 0; j < op->dummy.nbytes; ++i, ++j)
> +	for (j = 0; j < dummy_nbytes; ++i, ++j)
>  		out[i] = 0x0;
>  
>  	if (op->data.dir == SPI_MEM_DATA_OUT)

[...]

> diff --git a/drivers/spi/spi-mem.c b/drivers/spi/spi-mem.c
> index 0c79193d9697..7b204963bb62 100644
> --- a/drivers/spi/spi-mem.c
> +++ b/drivers/spi/spi-mem.c
> @@ -149,7 +149,7 @@ static bool spi_mem_check_buswidth(struct spi_mem *mem,
>  	    spi_check_buswidth_req(mem, op->addr.buswidth, true))
>  		return false;
>  
> -	if (op->dummy.nbytes &&
> +	if (op->dummy.ncycles &&
>  	    spi_check_buswidth_req(mem, op->dummy.buswidth, true))
>  		return false;
>  
> @@ -202,7 +202,7 @@ static int spi_mem_check_op(const struct spi_mem_op *op)
>  		return -EINVAL;
>  
>  	if ((op->addr.nbytes && !op->addr.buswidth) ||
> -	    (op->dummy.nbytes && !op->dummy.buswidth) ||
> +	    (op->dummy.ncycles && !op->dummy.buswidth) ||
>  	    (op->data.nbytes && !op->data.buswidth))
>  		return -EINVAL;
>  
> @@ -315,7 +315,7 @@ int spi_mem_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)

>  	struct spi_controller *ctlr = mem->spi->controller;
>  	struct spi_transfer xfers[4] = { };
>  	struct spi_message msg;
> -	u8 *tmpbuf;
> +	u8 *tmpbuf, dummy_nbytes;
>  	int ret;

Reverse xmas tree order?

>  
>  	ret = spi_mem_check_op(op);
> @@ -343,7 +343,11 @@ int spi_mem_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
>  			return ret;
>  	}
>  

> -	tmpbufsize = op->cmd.nbytes + op->addr.nbytes + op->dummy.nbytes;
> +	dummy_nbytes = (op->dummy.ncycles * op->dummy.buswidth) / 8;

So ncycles now indeed is a number of CLK line oscillations. This most
likely will break the SPI Nand driver then, which still passes the
number of bytes to the SPI_MEM_OP_DUMMY() macro.

> +	if (op->dummy.dtr)
> +		dummy_nbytes *= 2;

Generic SPI-mem ops don't take the DTR mode into account. So I don't
see this necessary.

> +
> +	tmpbufsize = op->cmd.nbytes + op->addr.nbytes + dummy_nbytes;
>  
>  	/*
>  	 * Allocate a buffer to transmit the CMD, ADDR cycles with kmalloc() so
> @@ -379,15 +383,15 @@ int spi_mem_exec_op(struct spi_mem *mem, const struct spi_mem_op *op)
>  		totalxferlen += op->addr.nbytes;
>  	}
>  
> -	if (op->dummy.nbytes) {
> -		memset(tmpbuf + op->addr.nbytes + 1, 0xff, op->dummy.nbytes);
> +	if (dummy_nbytes) {
> +		memset(tmpbuf + op->addr.nbytes + 1, 0xff, dummy_nbytes);
>  		xfers[xferpos].tx_buf = tmpbuf + op->addr.nbytes + 1;
> -		xfers[xferpos].len = op->dummy.nbytes;
> +		xfers[xferpos].len = dummy_nbytes;
>  		xfers[xferpos].tx_nbits = op->dummy.buswidth;
>  		xfers[xferpos].dummy_data = 1;
>  		spi_message_add_tail(&xfers[xferpos], &msg);
>  		xferpos++;
> -		totalxferlen += op->dummy.nbytes;
> +		totalxferlen += dummy_nbytes;
>  	}
>  
>  	if (op->data.nbytes) {
> @@ -456,12 +460,17 @@ int spi_mem_adjust_op_size(struct spi_mem *mem, struct spi_mem_op *op)
>  {

>  	struct spi_controller *ctlr = mem->spi->controller;
>  	size_t len;
> +	u8 dummy_nbytes;

reverse xmas tree?

>  
>  	if (ctlr->mem_ops && ctlr->mem_ops->adjust_op_size)
>  		return ctlr->mem_ops->adjust_op_size(mem, op);
>  
> +	dummy_nbytes = (op->dummy.ncycles * op->dummy.buswidth) / 8;
> +	if (op->dummy.dtr)
> +		dummy_nbytes *= 2;
> +
>  	if (!ctlr->mem_ops || !ctlr->mem_ops->exec_op) {
> -		len = op->cmd.nbytes + op->addr.nbytes + op->dummy.nbytes;
> +		len = op->cmd.nbytes + op->addr.nbytes + dummy_nbytes;
>  
>  		if (len > spi_max_transfer_size(mem->spi))
>  			return -EINVAL;

[...]
  
> diff --git a/drivers/spi/spi-mtk-nor.c b/drivers/spi/spi-mtk-nor.c
> index d167699a1a96..f6870c6e911a 100644
> --- a/drivers/spi/spi-mtk-nor.c
> +++ b/drivers/spi/spi-mtk-nor.c
> @@ -171,23 +171,18 @@ static bool need_bounce(struct mtk_nor *sp, const struct spi_mem_op *op)
>  
>  static bool mtk_nor_match_read(const struct spi_mem_op *op)
>  {
> -	int dummy = 0;
> -
> -	if (op->dummy.nbytes)
> -		dummy = op->dummy.nbytes * BITS_PER_BYTE / op->dummy.buswidth;
> -
>  	if ((op->data.buswidth == 2) || (op->data.buswidth == 4)) {
>  		if (op->addr.buswidth == 1)
> -			return dummy == 8;
> +			return op->dummy.ncycles == 8;
>  		else if (op->addr.buswidth == 2)
> -			return dummy == 4;
> +			return op->dummy.ncycles == 4;
>  		else if (op->addr.buswidth == 4)
> -			return dummy == 6;
> +			return op->dummy.ncycles == 6;
>  	} else if ((op->addr.buswidth == 1) && (op->data.buswidth == 1)) {
>  		if (op->cmd.opcode == 0x03)
> -			return dummy == 0;
> +			return op->dummy.ncycles == 0;
>  		else if (op->cmd.opcode == 0x0b)
> -			return dummy == 8;
> +			return op->dummy.ncycles == 8;
>  	}
>  	return false;
>  }
> @@ -195,6 +190,10 @@ static bool mtk_nor_match_read(const struct spi_mem_op *op)
>  static bool mtk_nor_match_prg(const struct spi_mem_op *op)
>  {
>  	int tx_len, rx_len, prg_len, prg_left;

> +	u8 dummy_nbytes = (op->dummy.ncycles * op->dummy.buswidth) / 8;
> +

IMO it's better to move the initialization statement to a separate
line here.

> +	if (op->dummy.dtr)
> +		dummy_nbytes *= 2;

Does the MTK SPI driver support DTR? AFAICS it doesn't.

>  
>  	// prg mode is spi-only.
>  	if ((op->cmd.buswidth > 1) || (op->addr.buswidth > 1) ||
> @@ -205,7 +204,7 @@ static bool mtk_nor_match_prg(const struct spi_mem_op *op)
>  
>  	if (op->data.dir == SPI_MEM_DATA_OUT) {
>  		// count dummy bytes only if we need to write data after it
> -		tx_len += op->dummy.nbytes;
> +		tx_len += dummy_nbytes;
>  
>  		// leave at least one byte for data
>  		if (tx_len > MTK_NOR_REG_PRGDATA_MAX)
> @@ -221,7 +220,7 @@ static bool mtk_nor_match_prg(const struct spi_mem_op *op)
>  			return false;
>  
>  		rx_len = op->data.nbytes;
> -		prg_left = MTK_NOR_PRG_CNT_MAX / 8 - tx_len - op->dummy.nbytes;
> +		prg_left = MTK_NOR_PRG_CNT_MAX / 8 - tx_len - dummy_nbytes;
>  		if (prg_left > MTK_NOR_REG_SHIFT_MAX + 1)
>  			prg_left = MTK_NOR_REG_SHIFT_MAX + 1;
>  		if (rx_len > prg_left) {
> @@ -230,11 +229,11 @@ static bool mtk_nor_match_prg(const struct spi_mem_op *op)
>  			rx_len = prg_left;
>  		}
>  
> -		prg_len = tx_len + op->dummy.nbytes + rx_len;
> +		prg_len = tx_len + dummy_nbytes + rx_len;
>  		if (prg_len > MTK_NOR_PRG_CNT_MAX / 8)
>  			return false;
>  	} else {
> -		prg_len = tx_len + op->dummy.nbytes;
> +		prg_len = tx_len + dummy_nbytes;
>  		if (prg_len > MTK_NOR_PRG_CNT_MAX / 8)
>  			return false;
>  	}
> @@ -244,15 +243,19 @@ static bool mtk_nor_match_prg(const struct spi_mem_op *op)
>  static void mtk_nor_adj_prg_size(struct spi_mem_op *op)
>  {
>  	int tx_len, tx_left, prg_left;

> +	u8 dummy_nbytes = (op->dummy.ncycles * op->dummy.buswidth) / 8;
> +
> +	if (op->dummy.dtr)
> +		dummy_nbytes *= 2;

ditto

>  
>  	tx_len = op->cmd.nbytes + op->addr.nbytes;
>  	if (op->data.dir == SPI_MEM_DATA_OUT) {
> -		tx_len += op->dummy.nbytes;
> +		tx_len += dummy_nbytes;
>  		tx_left = MTK_NOR_REG_PRGDATA_MAX + 1 - tx_len;
>  		if (op->data.nbytes > tx_left)
>  			op->data.nbytes = tx_left;
>  	} else if (op->data.dir == SPI_MEM_DATA_IN) {
> -		prg_left = MTK_NOR_PRG_CNT_MAX / 8 - tx_len - op->dummy.nbytes;
> +		prg_left = MTK_NOR_PRG_CNT_MAX / 8 - tx_len - dummy_nbytes;
>  		if (prg_left > MTK_NOR_REG_SHIFT_MAX + 1)
>  			prg_left = MTK_NOR_REG_SHIFT_MAX + 1;
>  		if (op->data.nbytes > prg_left)
> @@ -312,7 +315,7 @@ static bool mtk_nor_supports_op(struct spi_mem *mem,
>  			break;
>  		case SPI_MEM_DATA_OUT:
>  			if ((op->addr.buswidth == 1) &&
> -			    (op->dummy.nbytes == 0) &&
> +			    (op->dummy.ncycles == 0) &&
>  			    (op->data.buswidth == 1))
>  				return true;
>  			break;
> @@ -515,17 +518,20 @@ static int mtk_nor_spi_mem_prg(struct mtk_nor *sp, const struct spi_mem_op *op)
>  	int tx_len, prg_len;
>  	int i, ret;
>  	void __iomem *reg;

> -	u8 bufbyte;
> +	u8 bufbyte, dummy_nbytes = (op->dummy.ncycles * op->dummy.buswidth) / 8;
> +
> +	if (op->dummy.dtr)
> +		dummy_nbytes *= 2;

ditto

>  
>  	tx_len = op->cmd.nbytes + op->addr.nbytes;
>  
>  	// count dummy bytes only if we need to write data after it
>  	if (op->data.dir == SPI_MEM_DATA_OUT)
> -		tx_len += op->dummy.nbytes + op->data.nbytes;
> +		tx_len += dummy_nbytes + op->data.nbytes;
>  	else if (op->data.dir == SPI_MEM_DATA_IN)
>  		rx_len = op->data.nbytes;
>  
> -	prg_len = op->cmd.nbytes + op->addr.nbytes + op->dummy.nbytes +
> +	prg_len = op->cmd.nbytes + op->addr.nbytes + dummy_nbytes +
>  		  op->data.nbytes;
>  
>  	// an invalid op may reach here if the caller calls exec_op without
> @@ -550,7 +556,7 @@ static int mtk_nor_spi_mem_prg(struct mtk_nor *sp, const struct spi_mem_op *op)
>  	}
>  
>  	if (op->data.dir == SPI_MEM_DATA_OUT) {
> -		for (i = 0; i < op->dummy.nbytes; i++, reg_offset--) {
> +		for (i = 0; i < dummy_nbytes; i++, reg_offset--) {
>  			reg = sp->base + MTK_NOR_REG_PRGDATA(reg_offset);
>  			writeb(0, reg);
>  		}

[...]
  
> diff --git a/drivers/spi/spi-zynq-qspi.c b/drivers/spi/spi-zynq-qspi.c
> index 78f31b61a2aa..84b7db85548c 100644
> --- a/drivers/spi/spi-zynq-qspi.c
> +++ b/drivers/spi/spi-zynq-qspi.c
> @@ -527,7 +527,10 @@ static int zynq_qspi_exec_mem_op(struct spi_mem *mem,
>  {
>  	struct zynq_qspi *xqspi = spi_controller_get_devdata(mem->spi->master);
>  	int err = 0, i;
> -	u8 *tmpbuf;
> +	u8 *tmpbuf, dummy_nbytes = (op->dummy.ncycles * op->dummy.buswidth) / 8;

Separate line?

> +
> +	if (op->dummy.dtr)
> +		dummy_nbytes *= 2;

Is DTR supported by the driver?

>  
>  	dev_dbg(xqspi->dev, "cmd:%#x mode:%d.%d.%d.%d\n",
>  		op->cmd.opcode, op->cmd.buswidth, op->addr.buswidth,
> @@ -568,17 +571,17 @@ static int zynq_qspi_exec_mem_op(struct spi_mem *mem,
>  			err = -ETIMEDOUT;
>  	}
>  
> -	if (op->dummy.nbytes) {
> -		tmpbuf = kzalloc(op->dummy.nbytes, GFP_KERNEL);
> +	if (dummy_nbytes) {
> +		tmpbuf = kzalloc(dummy_nbytes, GFP_KERNEL);
>  		if (!tmpbuf)
>  			return -ENOMEM;
>  
> -		memset(tmpbuf, 0xff, op->dummy.nbytes);
> +		memset(tmpbuf, 0xff, dummy_nbytes);
>  		reinit_completion(&xqspi->data_completion);
>  		xqspi->txbuf = tmpbuf;
>  		xqspi->rxbuf = NULL;
> -		xqspi->tx_bytes = op->dummy.nbytes;
> -		xqspi->rx_bytes = op->dummy.nbytes;
> +		xqspi->tx_bytes = dummy_nbytes;
> +		xqspi->rx_bytes = dummy_nbytes;
>  		zynq_qspi_write_op(xqspi, ZYNQ_QSPI_FIFO_DEPTH, true);
>  		zynq_qspi_write(xqspi, ZYNQ_QSPI_IEN_OFFSET,
>  				ZYNQ_QSPI_IXR_RXTX_MASK);
> diff --git a/drivers/spi/spi-zynqmp-gqspi.c b/drivers/spi/spi-zynqmp-gqspi.c
> index c760aac070e5..b41abadef9a6 100644
> --- a/drivers/spi/spi-zynqmp-gqspi.c
> +++ b/drivers/spi/spi-zynqmp-gqspi.c
> @@ -948,6 +948,10 @@ static int zynqmp_qspi_exec_op(struct spi_mem *mem,
>  	u32 genfifoentry = 0;
>  	u16 opcode = op->cmd.opcode;
>  	u64 opaddr;

> +	u8 dummy_nbytes = (op->dummy.ncycles * op->dummy.buswidth) / 8;
> +
> +	if (op->dummy.dtr)
> +		dummy_nbytes *= 2;

ditto

>  
>  	dev_dbg(xqspi->dev, "cmd:%#x mode:%d.%d.%d.%d\n",
>  		op->cmd.opcode, op->cmd.buswidth, op->addr.buswidth,
> @@ -1006,14 +1010,14 @@ static int zynqmp_qspi_exec_op(struct spi_mem *mem,
>  		}
>  	}
>  
> -	if (op->dummy.nbytes) {
> +	if (dummy_nbytes) {
>  		xqspi->txbuf = NULL;
>  		xqspi->rxbuf = NULL;
>  		/*
>  		 * xqspi->bytes_to_transfer here represents the dummy circles
>  		 * which need to be sent.
>  		 */
> -		xqspi->bytes_to_transfer = op->dummy.nbytes * 8 / op->dummy.buswidth;
> +		xqspi->bytes_to_transfer = dummy_nbytes;
>  		xqspi->bytes_to_receive = 0;
>  		/*
>  		 * Using op->data.buswidth instead of op->dummy.buswidth here because
> diff --git a/include/linux/spi/spi-mem.h b/include/linux/spi/spi-mem.h
> index 2ba044d0d5e5..5fd45800af03 100644
> --- a/include/linux/spi/spi-mem.h
> +++ b/include/linux/spi/spi-mem.h
> @@ -29,9 +29,9 @@
>  
>  #define SPI_MEM_OP_NO_ADDR	{ }
>  

> -#define SPI_MEM_OP_DUMMY(__nbytes, __buswidth)			\
> +#define SPI_MEM_OP_DUMMY(__ncycles, __buswidth)		\
>  	{							\

> -		.nbytes = __nbytes,				\
> +		.ncycles = __ncycles,				\
>  		.buswidth = __buswidth,				\

Please make sure this update and the drivers/spi/spi-mem.c driver
alterations are coherent with the SPI Nand driver. See the macro usages:
include/linux/mtd/spinand.h: SPINAND_PAGE_READ_FROM_*().

-Sergey

>  	}
>  
> @@ -83,8 +83,8 @@ enum spi_mem_data_dir {
>   *	      Note that only @addr.nbytes are taken into account in this
>   *	      address value, so users should make sure the value fits in the
>   *	      assigned number of bytes.
> - * @dummy.nbytes: number of dummy bytes to send after an opcode or address. Can
> - *		  be zero if the operation does not require dummy bytes
> + * @dummy.ncycles: number of dummy cycles after an opcode or address. Can
> + *		   be zero if the operation does not require dummy cycles
>   * @dummy.buswidth: number of IO lanes used to transmit the dummy bytes
>   * @dummy.dtr: whether the dummy bytes should be sent in DTR mode or not
>   * @data.buswidth: number of IO lanes used to send/receive the data
> @@ -112,7 +112,7 @@ struct spi_mem_op {
>  	} addr;
>  
>  	struct {
> -		u8 nbytes;
> +		u8 ncycles;
>  		u8 buswidth;
>  		u8 dtr : 1;
>  	} dummy;
> -- 
> 2.34.1
> 



More information about the Linux-mediatek mailing list