[PATCH v9,4/7] thermal: mediatek: Add LVTS driver for mt8192 thermal zones
AngeloGioacchino Del Regno
angelogioacchino.delregno at collabora.com
Wed Sep 14 06:31:15 PDT 2022
Il 17/08/22 10:07, bchihi at baylibre.com ha scritto:
> From: Michael Kao <michael.kao at mediatek.com>
>
> Add LVTS v4 (Low Voltage Thermal Sensor) driver to report junction
> temperatures in MediaTek SoC mt8192 and register the maximum temperature
> of sensors and each sensor as a thermal zone.
Hello Balsam,
thanks for the patch! However, there's something to improve...
>
> Co-developed-by: Yu-Chia Chang <ethan.chang at mediatek.com>
> Signed-off-by: Yu-Chia Chang <ethan.chang at mediatek.com>
> Signed-off-by: Michael Kao <michael.kao at mediatek.com>
> Co-developed-by: Ben Tseng <ben.tseng at mediatek.com>
> Signed-off-by: Ben Tseng <ben.tseng at mediatek.com>
> Co-developed-by: Alexandre Bailon <abailon at baylibre.com>
> Signed-off-by: Alexandre Bailon <abailon at baylibre.com>
> Co-developed-by: Balsam CHIHI <bchihi at baylibre.com>
> Signed-off-by: Balsam CHIHI <bchihi at baylibre.com>
> ---
> drivers/thermal/mediatek/Kconfig | 21 +
> drivers/thermal/mediatek/Makefile | 2 +
> drivers/thermal/mediatek/lvts_thermal.c | 861 ++++++++++++++++++++++++
> drivers/thermal/mediatek/lvts_thermal.h | 385 +++++++++++
> drivers/thermal/mediatek/lvts_v4.c | 249 +++++++
> 5 files changed, 1518 insertions(+)
> create mode 100644 drivers/thermal/mediatek/lvts_thermal.c
> create mode 100644 drivers/thermal/mediatek/lvts_thermal.h
> create mode 100644 drivers/thermal/mediatek/lvts_v4.c
>
> diff --git a/drivers/thermal/mediatek/Kconfig b/drivers/thermal/mediatek/Kconfig
> index 8ff32370b591..02a1b3b42ce0 100644
> --- a/drivers/thermal/mediatek/Kconfig
> +++ b/drivers/thermal/mediatek/Kconfig
> @@ -19,4 +19,25 @@ config MTK_SOC_THERMAL
> information for MediaTek platforms. This driver configures
> thermal controllers to collect temperature via AUXADC interface.
>
> +config MTK_LVTS_THERMAL
> + tristate "LVTS temperature sensor driver for MediaTek SoCs"
> + depends on HAS_IOMEM
> + depends on NVMEM
> + depends on RESET_CONTROLLER
> + help
> + Enable this option if you want to get SoC temperature information
> + for MediaTek platforms. This driver configures LVTS
> + (Low Voltage Thermal Sensor) thermal controllers to collect
> + temperatures via ASIF (Analog Serial Interface).
> +
> +if MTK_LVTS_THERMAL
> +
> +config MTK_LVTS_V4
> + tristate "LVTS v4 driver for MediaTek SoCs"
> + help
> + Enable this option if you want to get temperature information
> + for LVTS v4 SoCs.
> +
> +endif
> +
> endif
> diff --git a/drivers/thermal/mediatek/Makefile b/drivers/thermal/mediatek/Makefile
> index bec325f06a46..e4e62d726776 100644
> --- a/drivers/thermal/mediatek/Makefile
> +++ b/drivers/thermal/mediatek/Makefile
> @@ -1 +1,3 @@
> obj-$(CONFIG_MTK_SOC_THERMAL) += auxadc_thermal.o
> +obj-$(CONFIG_MTK_LVTS_THERMAL) += lvts_thermal.o
> +obj-$(CONFIG_MTK_LVTS_V4) += lvts_v4.o
> diff --git a/drivers/thermal/mediatek/lvts_thermal.c b/drivers/thermal/mediatek/lvts_thermal.c
> new file mode 100644
> index 000000000000..a1681b914c69
> --- /dev/null
> +++ b/drivers/thermal/mediatek/lvts_thermal.c
> @@ -0,0 +1,861 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (c) 2022 MediaTek Inc.
> + */
> +
> +#include <linux/bits.h>
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/iopoll.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/nvmem-consumer.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/of_device.h>
> +#include <linux/of_irq.h>
> +#include <linux/platform_device.h>
> +#include <linux/reset.h>
> +#include <linux/slab.h>
> +#include <linux/string.h>
> +#include <linux/thermal.h>
> +#include "lvts_thermal.h"
> +
> +static int lvts_raw_to_temp(struct lvts_formula_coeff *co, unsigned int msr_raw)
> +{
> + /* This function returns degree mC */
> +
> + int temp;
> +
> + temp = (co->a * ((unsigned long long)msr_raw)) >> 14;
> + temp = temp + co->golden_temp * 500 + co->b;
> +
> + return temp;
> +}
> +
> +static unsigned int lvts_temp_to_raw(struct lvts_formula_coeff *co, int temp)
> +{
> + unsigned int msr_raw;
> +
> + msr_raw = div_s64((s64)((co->golden_temp * 500 + co->b - temp)) << 14, (-1 * co->a));
> +
> + return msr_raw;
> +}
> +
> +static int soc_temp_lvts_read_temp(void *data, int *temperature)
> +{
> + struct soc_temp_tz *lvts_tz = (struct soc_temp_tz *)data;
> + struct lvts_data *lvts_data = lvts_tz->lvts_data;
> + struct device *dev = lvts_data->dev;
> + unsigned int msr_raw;
> +
> + msr_raw = readl(lvts_data->reg[lvts_tz->id]) & MRS_RAW_MASK;
> + if (msr_raw == 0) {
> + /* Prevents a false critical temperature trap */
> + *temperature = 0;
> + dev_dbg(dev, "LVTS not yet ready\n");
...and you're not returning an error code, despite this function was called
while LVTS is still not ready? :-)
> +
> + } else
> + *temperature = lvts_raw_to_temp(&lvts_data->coeff, msr_raw);
> +
> + return 0;
> +}
> +
> +static const struct thermal_zone_of_device_ops soc_temp_lvts_ops = {
> + .get_temp = soc_temp_lvts_read_temp,
> +};
> +
> +static void lvts_write_device(struct lvts_data *lvts_data, unsigned int data, int tc_id)
> +{
> + void __iomem *base = GET_BASE_ADDR(lvts_data, tc_id);
> +
> + writel(DEVICE_WRITE(lvts_data) | data, LVTS_CONFIG_0 + base);
> + usleep_range(20, 30);
> +}
> +
> +static unsigned int lvts_read_device(struct lvts_data *lvts_data, unsigned int reg_idx, int tc_id)
> +{
> + void __iomem *base = GET_BASE_ADDR(lvts_data, tc_id);
> + struct device *dev = lvts_data->dev;
> + unsigned int data;
> + int ret;
> +
> + writel(READ_DEVICE_REG(lvts_data, reg_idx), LVTS_CONFIG_0 + base);
> + usleep_range(20, 30);
> + ret = readl_poll_timeout(LVTS_CONFIG_0 + base, data, !(data & DEVICE_ACCESS_STARTUS), 2, 200);
> + if (ret)
> + dev_err(dev, "LVTS_TC_%d DEVICE_ACCESS_START is not ready\n", tc_id);
> +
> + data = readl(LVTSRDATA0_0 + base);
If DEVICE_ACCESS_START is not ready, you're not caring at all and still going on
with your register read, which I expect to fail by returning invalid data during
LVTS setup, which could produce wrong temperature readouts later: even though in
function soc_temp_lvts_read_temp() you're checking if msr_raw is zero, that may
not be enough as, if the setup is wrong, you may get a temperature offset that
will not necessarily make us read zero at msr_raw.
Think about if this leads to a CPU temperature readout of 200°C: the system will
shutdown for over-temperature, but that situation wouldn't be true.
Of course, the opposite could happen, with a reading of sub-zero temperatures,
for which the thermal framework (if configured to do so) will limit the frequency
of CPU/GPU/whatever else to the minimum.
I'm sure that you know the implications, anyway, so you will agree with me
that such condition would be definitely not ideal.
Please fix that.
> +
> + return data;
> +}
> +
> +static const char * const lvts_error_table[] = {
> + "Idle",
> + "Write transaction",
> + "Waiting for read after write",
> + "Disable continue fetching on device",
> + "Read transaction",
> + "Set device special register for voltage threshold",
> + "Set TSMCU number for fetch"
> +};
> +
> +static void wait_all_tc_sensing_point_idle(struct lvts_data *lvts_data)
> +{
> + void __iomem *base;
> + struct device *dev = lvts_data->dev;
> + unsigned int error_code, is_error;
You don't need the `is_error` variable.
> + int i, cnt, ret;
> +
> + for (cnt = 0; cnt < 2; cnt++) {
> + is_error = 0;
> +
> + for (i = 0; i < lvts_data->num_tc; i++) {
> + base = GET_BASE_ADDR(lvts_data, i);
> + ret = readl_poll_timeout(LVTSMSRCTL1_0 + base, error_code,
> + !(error_code & ALL_TC_SENSING_POINT_STATUS), 2, 200);
> + error_code = ((error_code & TC_SENSING_POINT_10) >> 8) +
> + ((error_code & TC_SENSING_POINT_7) >> 6) + (error_code & TC_SENSING_POINT_0);
> + if (ret)
> + dev_err(dev, "LVTS_TC_%d Error Code : %s\n", i, lvts_error_table[error_code]);
you're not printing the error code, so just "LVTS_TC%d Error: %s\n"
> +
> + if (error_code != 0)
> + is_error = 1;
> + }
> +
> + if (is_error == 0)
> + break;
> + }
...if anything goes wrong, this function should return an error for the caller
to take action (recovery, reset, retry or whatever else).
return ret; (and please, set ret as the right error for error_code).
> +}
> +
> +static void lvts_reset(struct lvts_data *lvts_data)
> +{
if (IS_ERR_OR_NULL(lvts_data->reset))
return;
reset_control_assert(lvts_data->reset);
reset_control_deassert(lvts_data->reset);
That's better... :-)
> + if (lvts_data->reset)
> + reset_control_assert(lvts_data->reset);
> +
> + if (lvts_data->reset)
> + reset_control_deassert(lvts_data->reset);
> +}
> +
> +static void device_identification(struct lvts_data *lvts_data)
> +{
> + void __iomem *base;
> + struct device *dev = lvts_data->dev;
> + unsigned int i, data;
> +
> + for (i = 0; i < lvts_data->num_tc; i++) {
> + base = GET_BASE_ADDR(lvts_data, i);
> + writel(ENABLE_LVTS_CTRL_CLK, LVTSCLKEN_0 + base);
> + lvts_write_device(lvts_data, RESET_ALL_DEVICES(lvts_data), i);
> + writel(READ_BACK_DEVICE_ID(lvts_data), LVTS_CONFIG_0 + base);
> + usleep_range(20, 30);
> + /* Check LVTS device ID */
> + data = (readl(LVTS_ID_0 + base) & DEVICE_REG_DATA);
> + if (data != (lvts_data->tc->dev_id + i))
> + dev_err(dev, "LVTS_TC_%d, Device ID should be 0x%x, but 0x%x\n",
> + i, (lvts_data->tc->dev_id + i), data);
Judging by the error message, this function should return an error number when
the dev_id is unknown, as this driver is likely to malfunction if this happens.
> + }
> +}
> +
> +static void disable_all_sensing_points(struct lvts_data *lvts_data)
> +{
> + void __iomem *base;
> + unsigned int i;
> +
> + for (i = 0; i < lvts_data->num_tc; i++) {
> + base = GET_BASE_ADDR(lvts_data, i);
> + writel(DISABLE_SENSING_POINT, LVTSMONCTL0_0 + base);
> + }
> +}
> +
> +static void enable_all_sensing_points(struct lvts_data *lvts_data)
> +{
> + void __iomem *base;
> + struct device *dev = lvts_data->dev;
> + const struct lvts_tc_settings *tc = lvts_data->tc;
> + unsigned int i, num;
> +
> + for (i = 0; i < lvts_data->num_tc; i++) {
> + base = GET_BASE_ADDR(lvts_data, i);
> + num = tc[i].num_sensor;
> + if (num > ALL_SENSING_POINTS) {
> + dev_err(dev, "LVTS_TC_%d, illegal number of sensors: %d\n", i, tc[i].num_sensor);
> +
Please remove this extra white line.
> + continue;
> + }
> +
> + if ((tc[i].ts_offset == 1) && (num == 1))
> + writel(LVTS_SINGLE_SENSE | (0x1 << tc[i].ts_offset), LVTSMONCTL0_0 + base);
> +
> + else
> + writel(ENABLE_SENSING_POINT(num), LVTSMONCTL0_0 + base);
> + }
> +}
> +
..snip..
> +
> +static int lvts_init(struct lvts_data *lvts_data)
> +{
> + struct platform_ops *ops = &lvts_data->ops;
> + struct device *dev = lvts_data->dev;
> + int ret;
> +
> + ret = clk_prepare_enable(lvts_data->clk);
> + if (ret) {
> + dev_err(dev, "Failed to enable lvts controller clock: %d\n", ret);
> +
same here
> + return ret;
> + }
> +
> + lvts_reset(lvts_data);
> + device_identification(lvts_data);
> + if (ops->device_enable_and_init)
> + ops->device_enable_and_init(lvts_data);
> +
> + if (HAS_FEATURE(lvts_data, FEATURE_DEVICE_AUTO_RCK) && (ops->device_enable_auto_rck))
> + ops->device_enable_auto_rck(lvts_data);
> +
> + else if (ops->device_read_count_rc_n)
> + ops->device_read_count_rc_n(lvts_data);
> +
> + if (ops->set_cal_data)
> + ops->set_cal_data(lvts_data);
> +
> + disable_all_sensing_points(lvts_data);
> + wait_all_tc_sensing_point_idle(lvts_data);
> + if (ops->init_controller)
> + ops->init_controller(lvts_data);
> +
> + enable_all_sensing_points(lvts_data);
> + set_all_tc_hw_reboot(lvts_data);
> +
> + return 0;
> +}
> +
> +static int prepare_calibration_data(struct lvts_data *lvts_data)
> +{
> + struct device *dev = lvts_data->dev;
> + struct lvts_sensor_cal_data *cal_data = &lvts_data->cal_data;
> + struct platform_ops *ops = &lvts_data->ops;
> + int i;
> +
> + cal_data->count_r = devm_kcalloc(dev, lvts_data->num_sensor,
> + sizeof(*cal_data->count_r), GFP_KERNEL);
> + if (!cal_data->count_r)
> + return -ENOMEM;
> +
> + cal_data->count_rc = devm_kcalloc(dev, lvts_data->num_sensor,
> + sizeof(*cal_data->count_rc), GFP_KERNEL);
> + if (!cal_data->count_rc)
> + return -ENOMEM;
> +
> + if (ops->efuse_to_cal_data && !cal_data->use_fake_efuse)
> + ops->efuse_to_cal_data(lvts_data);
> +
> + if (cal_data->golden_temp == 0 || cal_data->golden_temp > GOLDEN_TEMP_MAX)
> + cal_data->use_fake_efuse = 1;
> +
> + if (cal_data->use_fake_efuse) {
> + /* It means all efuse data are equal to 0 */
> + dev_err(dev, "This sample is not calibrated, fake !!\n");
> + cal_data->golden_temp = cal_data->default_golden_temp;
> + for (i = 0; i < lvts_data->num_sensor; i++) {
> + cal_data->count_r[i] = cal_data->default_count_r;
> + cal_data->count_rc[i] = cal_data->default_count_rc;
> + }
> + }
> +
> + lvts_data->coeff.golden_temp = cal_data->golden_temp;
> + dev_dbg(dev, "golden_temp = %d\n", cal_data->golden_temp);
> +
> + return 0;
> +}
> +
> +static int get_calibration_data(struct lvts_data *lvts_data)
> +{
> + struct device *dev = lvts_data->dev;
> + char cell_name[32];
> + struct nvmem_cell *cell;
> + u32 *buf;
> + size_t len;
> + int i, j, index = 0, ret;
> +
> + lvts_data->efuse = devm_kcalloc(dev, lvts_data->num_efuse_addr,
> + sizeof(*lvts_data->efuse), GFP_KERNEL);
> + if (!lvts_data->efuse)
> + return -ENOMEM;
> +
> + for (i = 0; i < lvts_data->num_efuse_block; i++) {
> + snprintf(cell_name, sizeof(cell_name), "lvts_calib_data%d", i + 1);
Can we please avoid using underscores? lvts-calib-data%d looks a bit better,
especially in devicetree.
> + cell = nvmem_cell_get(dev, cell_name);
> + if (IS_ERR(cell)) {
> + dev_err(dev, "Failed to get nvmem cell %s\n", cell_name);
> +
> + return PTR_ERR(cell);
> + }
> +
> + buf = (u32 *)nvmem_cell_read(cell, &len);
> + nvmem_cell_put(cell);
> + if (IS_ERR(buf))
> + return PTR_ERR(buf);
> +
> + for (j = 0; j < (len / sizeof(u32)); j++) {
> + if (index >= lvts_data->num_efuse_addr) {
> + dev_err(dev, "Array efuse is going to overflow");
> + kfree(buf);
> +
> + return -EINVAL;
> + }
> +
> + lvts_data->efuse[index] = buf[j];
> + index++;
> + }
> +
> + kfree(buf);
> + }
> +
> + ret = prepare_calibration_data(lvts_data);
> +
> + return ret;
> +}
> +
> +static int lvts_init_tc_regs(struct device *dev, struct lvts_data *lvts_data)
> +{
> + void __iomem *base;
> + const struct lvts_tc_settings *tc = lvts_data->tc;
> + unsigned int i, j, s_index, x;
> +
> + lvts_data->reg = devm_kcalloc(dev, lvts_data->num_sensor,
> + sizeof(*lvts_data->reg), GFP_KERNEL);
> + if (!lvts_data->reg)
> + return -ENOMEM;
> +
> + for (i = 0; i < lvts_data->num_tc; i++) {
> + base = GET_BASE_ADDR(lvts_data, i);
> + for (j = 0; j < tc[i].num_sensor; j++) {
> + s_index = tc[i].sensor_map[j];
> + x = j + tc[i].ts_offset;
> + lvts_data->reg[s_index] = LVTSMSR0_0 + base + 0x4 * x;
> + }
> + }
> +
> + return 0;
> +}
> +
> +static int of_update_lvts_data(struct lvts_data *lvts_data, struct platform_device *pdev)
> +{
> + struct device *dev = lvts_data->dev;
> + struct resource *res;
> + int ret;
> +
> + lvts_data->clk = devm_clk_get(dev, NULL);
> + if (IS_ERR(lvts_data->clk))
> + return PTR_ERR(lvts_data->clk);
> +
> + /* Get base address */
> + res = platform_get_mem_or_io(pdev, 0);
> + if (!res) {
> + dev_err(dev, "No IO resource\n");
> +
> + return -ENXIO;
> + }
> +
> + lvts_data->base = devm_ioremap_resource(dev, res);
> + if (IS_ERR(lvts_data->base)) {
> + dev_err(dev, "Failed to remap io\n");
> +
> + return PTR_ERR(lvts_data->base);
> + }
> +
> + /* Get interrupt number */
> + ret = platform_get_irq(pdev, 0);
> + if (ret < 0) {
> + dev_err(dev, "No irq resource\n");
> +
> + return ret;
> + }
> +
> + lvts_data->irq_num = ret;
> + /* Get reset control */
> + lvts_data->reset = devm_reset_control_get_by_index(dev, 0);
> + if (IS_ERR(lvts_data->reset)) {
> + dev_err(dev, "Failed to get reset control\n");
> +
> + return PTR_ERR(lvts_data->reset);
> + }
> +
> + ret = lvts_init_tc_regs(dev, lvts_data);
> + if (ret)
> + return ret;
> +
> + ret = get_calibration_data(lvts_data);
> + if (ret)
> + return ret;
> +
> + return 0;
> +}
> +
> +static void lvts_device_close(struct lvts_data *lvts_data)
> +{
> + void __iomem *base;
> + unsigned int i;
> +
> + for (i = 0; i < lvts_data->num_tc; i++) {
> + base = GET_BASE_ADDR(lvts_data, i);
> + lvts_write_device(lvts_data, RESET_ALL_DEVICES(lvts_data), i);
> + writel(DISABLE_LVTS_CTRL_CLK, LVTSCLKEN_0 + base);
> + }
> +}
> +
> +static void lvts_close(struct lvts_data *lvts_data)
> +{
> + disable_all_sensing_points(lvts_data);
> + wait_all_tc_sensing_point_idle(lvts_data);
> + lvts_device_close(lvts_data);
> + clk_disable_unprepare(lvts_data->clk);
> +}
> +
> +static void tc_irq_handler(struct lvts_data *lvts_data, int tc_id)
> +{
> + void __iomem *base = GET_BASE_ADDR(lvts_data, tc_id);
> + const struct device *dev = lvts_data->dev;
> + unsigned int ret = readl(LVTSMONINTSTS_0 + base);
> +
> + /* Write back to clear interrupt status */
> + writel(ret, LVTSMONINTSTS_0 + base);
> + dev_dbg(dev, "LVTS thermal controller %d, LVTSMONINTSTS=0x%08x\n", tc_id, ret);
> + if (ret & THERMAL_PROTECTION_STAGE_3)
> + dev_dbg(dev, "Thermal protection stage 3 interrupt triggered\n");
> +}
> +
> +static irqreturn_t irq_handler(int irq, void *dev_id)
> +{
> + void __iomem *base;
> + struct lvts_data *lvts_data = (struct lvts_data *)dev_id;
> + struct device *dev = lvts_data->dev;
> + const struct lvts_tc_settings *tc = lvts_data->tc;
> + unsigned int i, irq_bitmap;
> +
> + base = lvts_data->base;
> + irq_bitmap = readl(THERMINTST + base);
> + dev_dbg(dev, "THERMINTST = 0x%x\n", irq_bitmap);
> + for (i = 0; i < lvts_data->num_tc; i++) {
> + if (tc[i].irq_bit == 0)
> + tc_irq_handler(lvts_data, i);
> + }
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int lvts_register_irq_handler(struct lvts_data *lvts_data)
> +{
> + struct device *dev = lvts_data->dev;
> + int ret;
> +
> + ret = devm_request_irq(dev, lvts_data->irq_num, irq_handler, IRQF_TRIGGER_NONE,
> + "mtk_lvts", lvts_data);
> + if (ret) {
> + dev_err(dev, "Failed to register LVTS IRQ, ret %d, irq_num %d\n",
> + ret, lvts_data->irq_num);
> + lvts_close(lvts_data);
> +
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int lvts_register_thermal_zones(struct lvts_data *lvts_data)
> +{
> + struct device *dev = lvts_data->dev;
> + struct thermal_zone_device *tzdev;
> + struct soc_temp_tz *lvts_tz;
> + int i, ret;
> +
> + for (i = 0; i < lvts_data->num_sensor; i++) {
> + lvts_tz = devm_kzalloc(dev, sizeof(*lvts_tz), GFP_KERNEL);
> + if (!lvts_tz) {
> + lvts_close(lvts_data);
> +
> + return -ENOMEM;
> + }
> +
> + lvts_tz->id = i;
> + lvts_tz->lvts_data = lvts_data;
> + tzdev = devm_thermal_zone_of_sensor_register(dev, lvts_tz->id, lvts_tz,
> + &soc_temp_lvts_ops);
> + if (IS_ERR(tzdev)) {
> + if (lvts_tz->id != 0)
> + return 0;
> +
> + ret = PTR_ERR(tzdev);
> + dev_err(dev, "Failed to register lvts tz %d, ret = %d\n", lvts_tz->id, ret);
> + lvts_close(lvts_data);
> +
> + return ret;
> + }
> + }
> +
> + return 0;
> +}
> +
> +void lvts_device_enable_and_init(struct lvts_data *lvts_data)
> +{
> + unsigned int i;
> +
> + for (i = 0; i < lvts_data->num_tc; i++) {
> + lvts_write_device(lvts_data, STOP_COUNTING_V4, i);
> + lvts_write_device(lvts_data, SET_RG_TSFM_LPDLY_V4, i);
> + lvts_write_device(lvts_data, SET_COUNTING_WINDOW_20US1_V4, i);
> + lvts_write_device(lvts_data, SET_COUNTING_WINDOW_20US2_V4, i);
> + lvts_write_device(lvts_data, TSV2F_CHOP_CKSEL_AND_TSV2F_EN_V4, i);
> + lvts_write_device(lvts_data, TSBG_DEM_CKSEL_X_TSBG_CHOP_EN_V4, i);
> + lvts_write_device(lvts_data, SET_TS_RSV_V4, i);
> + lvts_write_device(lvts_data, SET_TS_EN_V4, i);
> + lvts_write_device(lvts_data, TOGGLE_RG_TSV2F_VCO_RST1_V4, i);
> + lvts_write_device(lvts_data, TOGGLE_RG_TSV2F_VCO_RST2_V4, i);
> + }
> +
> + lvts_data->counting_window_us = 20;
> +}
> +EXPORT_SYMBOL_GPL(lvts_device_enable_and_init);
> +
> +void lvts_device_enable_auto_rck_v4(struct lvts_data *lvts_data)
> +{
> + unsigned int i;
> +
> + for (i = 0; i < lvts_data->num_tc; i++)
> + lvts_write_device(lvts_data, SET_LVTS_AUTO_RCK_V4, i);
> +}
> +EXPORT_SYMBOL_GPL(lvts_device_enable_auto_rck_v4);
> +
> +int lvts_device_read_count_rc_n_v4(struct lvts_data *lvts_data)
> +{
> + void __iomem *base;
> + struct device *dev = lvts_data->dev;
> + const struct lvts_tc_settings *tc = lvts_data->tc;
> + struct lvts_sensor_cal_data *cal_data = &lvts_data->cal_data;
> + unsigned int s_index, data;
> + int ret, i, j;
> +
> + cal_data->count_rc_now = devm_kcalloc(dev, lvts_data->num_sensor,
> + sizeof(*cal_data->count_rc_now), GFP_KERNEL);
> + if (!cal_data->count_rc_now)
> + return -ENOMEM;
> +
> + for (i = 0; i < lvts_data->num_tc; i++) {
> + base = GET_BASE_ADDR(lvts_data, i);
> + for (j = 0; j < tc[i].num_sensor; j++) {
> + s_index = tc[i].sensor_map[j];
> + lvts_write_device(lvts_data, SELECT_SENSOR_RCK_V4(j), i);
> + lvts_write_device(lvts_data, SET_DEVICE_SINGLE_MODE_V4, i);
> + lvts_write_device(lvts_data, KICK_OFF_RCK_COUNTING_V4, i);
> + ret = readl_poll_timeout(LVTS_CONFIG_0 + base, data,
> + !(data & DEVICE_SENSING_STATUS), 2, 200);
> + if (ret)
> + dev_err(dev, "LVTS_TC_%d DEVICE_SENSING_STATUS didn't ready\n", i);
> +
> + data = lvts_read_device(lvts_data, 0x00, i);
> + cal_data->count_rc_now[s_index] = (data & COUNT_RC_NOW_MASK);
> + }
> +
> + /* Recover Setting for Normal Access on
> + * temperature fetch
> + */
> + lvts_write_device(lvts_data, SET_SENSOR_NO_RCK_V4, i);
> + lvts_write_device(lvts_data, SET_DEVICE_LOW_POWER_SINGLE_MODE_V4, i);
> + }
> +
> + return 0;
> +}
> +EXPORT_SYMBOL_GPL(lvts_device_read_count_rc_n_v4);
> +
> +void lvts_set_calibration_data_v4(struct lvts_data *lvts_data)
> +{
> + void __iomem *base;
> + const struct lvts_tc_settings *tc = lvts_data->tc;
> + struct lvts_sensor_cal_data *cal_data = &lvts_data->cal_data;
> + unsigned int i, j, s_index, x;
> + u32 lvts_calib_data;
> +
> + for (i = 0; i < lvts_data->num_tc; i++) {
> + base = GET_BASE_ADDR(lvts_data, i);
> + for (j = 0; j < tc[i].num_sensor; j++) {
> + s_index = tc[i].sensor_map[j];
> + x = j + tc[i].ts_offset;
> + if (HAS_FEATURE(lvts_data, FEATURE_DEVICE_AUTO_RCK))
> + lvts_calib_data = cal_data->count_r[s_index];
> +
> + else
> + lvts_calib_data = (((u32)cal_data->count_rc_now[s_index]) *
> + cal_data->count_r[s_index]) >> 14;
> +
> + writel(lvts_calib_data, LVTSEDATA00_0 + base + 0x4 * x);
> + }
> + }
> +}
> +EXPORT_SYMBOL_GPL(lvts_set_calibration_data_v4);
> +
> +void lvts_init_controller_v4(struct lvts_data *lvts_data)
> +{
> + void __iomem *base;
> + struct device *dev = lvts_data->dev;
> + unsigned int i;
> +
> + for (i = 0; i < lvts_data->num_tc; i++) {
> + base = GET_BASE_ADDR(lvts_data, i);
> + lvts_write_device(lvts_data, SET_DEVICE_LOW_POWER_SINGLE_MODE_V4, i);
> + writel(SET_SENSOR_INDEX, LVTSTSSEL_0 + base);
> + writel(SET_CALC_SCALE_RULES, LVTSCALSCALE_0 + base);
> + set_polling_speed(lvts_data, i);
> + set_hw_filter(lvts_data, i);
> + dev_dbg(dev, "lvts_tc_%d: read all %d sensors in %d us, one in %d us\n",
> + i, GET_TC_SENSOR_NUM(lvts_data, i), GROUP_LATENCY_US(lvts_data, i),
> + SENSOR_LATENCY_US(lvts_data, i));
> + }
> +}
> +EXPORT_SYMBOL_GPL(lvts_init_controller_v4);
> +
> +int lvts_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct lvts_data *lvts_data;
> + int ret;
> +
> + lvts_data = (struct lvts_data *)of_device_get_match_data(dev);
> + if (!lvts_data) {
> + dev_err(dev, "Failed to get lvts platform data\n");
> +
> + return -ENODATA;
> + }
> +
> + lvts_data->dev = &pdev->dev;
> + ret = of_update_lvts_data(lvts_data, pdev);
> + if (ret)
> + return ret;
> +
> + platform_set_drvdata(pdev, lvts_data);
> + ret = lvts_init(lvts_data);
> + if (ret)
> + return ret;
> +
> + ret = lvts_register_irq_handler(lvts_data);
> + if (ret)
> + return ret;
> +
> + ret = lvts_register_thermal_zones(lvts_data);
> + if (ret)
> + return ret;
> +
> + return 0;
> +}
> +
> +int lvts_remove(struct platform_device *pdev)
> +{
> + struct lvts_data *lvts_data;
> +
> + lvts_data = (struct lvts_data *)platform_get_drvdata(pdev);
> + lvts_close(lvts_data);
> +
> + return 0;
> +}
> +
> +int lvts_suspend(struct platform_device *pdev, pm_message_t state)
> +{
> + int ret;
> +
> + ret = lvts_remove(pdev);
> + if (ret)
> + return ret;
> +
> + return 0;
> +}
> +
> +int lvts_resume(struct platform_device *pdev)
> +{
> + int ret;
> +
> + ret = lvts_probe(pdev);
> + if (ret)
> + return ret;
> +
> + return 0;
> +}
> +
> +void lvts_shutdown(struct platform_device *pdev)
> +{
> + lvts_remove(pdev);
> +}
> +
> +MODULE_AUTHOR("Yu-Chia Chang <ethan.chang at mediatek.com>");
> +MODULE_AUTHOR("Michael Kao <michael.kao at mediatek.com>");
> +MODULE_DESCRIPTION("MediaTek LVTS Thermal Driver");
> +MODULE_LICENSE("GPL");
> diff --git a/drivers/thermal/mediatek/lvts_thermal.h b/drivers/thermal/mediatek/lvts_thermal.h
> new file mode 100644
> index 000000000000..a94ce46acccd
> --- /dev/null
> +++ b/drivers/thermal/mediatek/lvts_thermal.h
> @@ -0,0 +1,385 @@
> +/* SPDX-License-Identifier: GPL-2.0-only */
> +/*
> + * Copyright (c) 2022 MediaTek Inc.
> + */
> +
> +#ifndef __MTK_SOC_TEMP_LVTS_H__
> +#define __MTK_SOC_TEMP_LVTS_H__
> +
> +#define PERIOD_UNIT 12
> +#define GROUP_INTERVAL_DELAY 1
> +#define FILTER_INTERVAL_DELAY 1
> +#define SENSOR_INTERVAL_DELAY 1
> +
> +#define HW_REBOOT_TRIP_POINT 117000
> +
> +#define FEATURE_DEVICE_AUTO_RCK BIT(0)
> +#define NUM_EFUSE_ADDR 22
> +#define NUM_EFUSE_BLOCK_MT8192 1
> +#define DEFAULT_GOLDEN_TEMP 50
> +#define DEFAULT_CUONT_R 35000
> +#define DEFAULT_CUONT_RC 2750
> +#define COEFF_A -250460
> +#define COEFF_B 250460
> +
> +#define CLOCK_26MHZ_CYCLE_NS 38
> +#define BUS_ACCESS_US 2
> +#define GOLDEN_TEMP_MAX 62
> +
> +#define LVTS_FILTER_SAMPLES_1 1
> +#define LVTS_FILTER_SAMPLES_2 2
> +#define LVTS_FILTER_SAMPLES_4 4
> +#define LVTS_FILTER_SAMPLES_6 6
> +#define LVTS_FILTER_SAMPLES_10 10
> +#define LVTS_FILTER_SAMPLES_18 18
> +
> +#define TC_SENSING_POINT_0 BIT(0)
> +#define TC_SENSING_POINT_7 BIT(7)
> +#define TC_SENSING_POINT_10 BIT(10)
> +#define ALL_TC_SENSING_POINT_STATUS (BIT(10) | BIT(7) | BIT(0))
> +#define COUNT_RC_NOW_MASK GENMASK(23, 0)
> +#define PERIOD_UNIT_MASK GENMASK(9, 0)
> +#define GROUP_INTERVAL_DELAY_MASK GENMASK(29, 20)
> +#define FILTER_INTERVAL_DELAY_MASK GENMASK(25, 16)
> +#define SENSOR_INTERVAL_DELAY_MASK GENMASK(9, 0)
> +
> +/* LVTS device register */
> +#define RG_TSFM_DATA_0 0x00
> +#define RG_TSFM_DATA_1 0x01
> +#define RG_TSFM_DATA_2 0x02
> +#define RG_TSFM_CTRL_0 0x03
> +#define RG_TSFM_CTRL_1 0x04
> +#define RG_TSFM_CTRL_2 0x05
> +#define RG_TSFM_CTRL_3 0x06
> +#define RG_TSFM_CTRL_4 0x07
> +#define RG_TSV2F_CTRL_0 0x08
> +#define RG_TSV2F_CTRL_1 0x09
> +#define RG_TSV2F_CTRL_2 0x0A
> +#define RG_TSV2F_CTRL_3 0x0B
> +#define RG_TSV2F_CTRL_4 0x0C
> +#define RG_TSV2F_CTRL_5 0x0D
> +#define RG_TSV2F_CTRL_6 0x0E
> +#define RG_TEMP_DATA_0 0x10
> +#define RG_TEMP_DATA_1 0x11
> +#define RG_TEMP_DATA_2 0x12
> +#define RG_TEMP_DATA_3 0x13
> +#define RG_RC_DATA_0 0x14
> +#define RG_RC_DATA_1 0x15
> +#define RG_RC_DATA_2 0x16
> +#define RG_RC_DATA_3 0x17
> +#define RG_DIV_DATA_0 0x18
> +#define RG_DIV_DATA_1 0x19
> +#define RG_DIV_DATA_2 0x1A
> +#define RG_DIV_DATA_3 0x1B
> +#define RG_TST_DATA_0 0x70
> +#define RG_TST_DATA_1 0x71
> +#define RG_TST_DATA_2 0x72
> +#define RG_TST_CTRL 0x73
> +#define RG_DBG_FQMTR 0xF0
> +#define RG_DBG_LPSEQ 0xF1
> +#define RG_DBG_STATE 0xF2
> +#define RG_DBG_CHKSUM 0xF3
> +#define RG_DID_LVTS 0xFC
> +#define RG_DID_REV 0xFD
> +#define RG_TSFM_RST 0xFF
> +
> +/* LVTS controller register */
> +#define LVTSMONCTL0_0 0x000
> +#define ENABLE_SENSING_POINT(num) (LVTS_SINGLE_SENSE | GENMASK(((num) - 1), 0))
> +#define DISABLE_SENSING_POINT (LVTS_SINGLE_SENSE | 0x0)
> +#define LVTSMONCTL1_0 0x004
> +#define LVTSMONCTL2_0 0x008
> +#define LVTSMONINT_0 0x00C
> +#define STAGE3_INT_EN BIT(31)
> +#define LVTSMONINTSTS_0 0x010
> +#define LVTSMONIDET0_0 0x014
> +#define LVTSMONIDET1_0 0x018
> +#define LVTSMONIDET2_0 0x01C
> +#define LVTSMONIDET3_0 0x020
> +#define LVTSH2NTHRE_0 0x024
> +#define LVTSHTHRE_0 0x028
> +#define LVTSCTHRE_0 0x02C
> +#define LVTSOFFSETH_0 0x030
> +#define LVTSOFFSETL_0 0x034
> +#define LVTSMSRCTL0_0 0x038
> +#define LVTSMSRCTL1_0 0x03C
> +#define LVTSTSSEL_0 0x040
> +#define SET_SENSOR_INDEX 0x13121110
> +#define LVTSDEVICETO_0 0x044
> +#define LVTSCALSCALE_0 0x048
> +#define SET_CALC_SCALE_RULES 0x00000300
> +#define LVTS_ID_0 0x04C
> +#define LVTS_CONFIG_0 0x050
> +
> +#define SCK_ONLY BIT(31)
> +#define BROADCAST_ID_UPDATE BIT(26)
> +#define DEVICE_SENSING_STATUS BIT(25)
> +#define DEVICE_ACCESS_STARTUS BIT(24)
> +#define READ_32BIT_ACCESS BIT(17)
> +#define WRITE_ACCESS BIT(16)
> +#define LVTS_SINGLE_SENSE BIT(9)
> +#define FEATURE_CK26M_ACTIVE BIT(1)
> +#define DEVICE_REG_DATA GENMASK(7, 0)
> +
> +#define LVTSEDATA00_0 0x054
> +#define LVTSEDATA01_0 0x058
> +#define LVTSEDATA02_0 0x05C
> +#define LVTSEDATA03_0 0x060
> +#define LVTSMSR0_0 0x090
> +#define MRS_RAW_MASK GENMASK(15, 0)
> +#define MRS_RAW_VALID_BIT BIT(16)
> +#define LVTSMSR1_0 0x094
> +#define LVTSMSR2_0 0x098
> +#define LVTSMSR3_0 0x09C
> +#define LVTSIMMD0_0 0x0A0
> +#define LVTSIMMD1_0 0x0A4
> +#define LVTSIMMD2_0 0x0A8
> +#define LVTSIMMD3_0 0x0AC
> +#define LVTSRDATA0_0 0x0B0
> +#define LVTSRDATA1_0 0x0B4
> +#define LVTSRDATA2_0 0x0B8
> +#define LVTSRDATA3_0 0x0BC
> +#define LVTSPROTCTL_0 0x0C0
> +#define PROTOFFSET GENMASK(15, 0)
> +#define LVTSPROTTA_0 0x0C4
> +#define LVTSPROTTB_0 0x0C8
> +#define LVTSPROTTC_0 0x0CC
> +#define LVTSCLKEN_0 0x0E4
> +#define ENABLE_LVTS_CTRL_CLK (1)
> +#define DISABLE_LVTS_CTRL_CLK (0)
> +#define LVTSDBGSEL_0 0x0E8
> +#define LVTSDBGSIG_0 0x0EC
> +#define LVTSSPARE0_0 0x0F0
> +#define LVTSSPARE1_0 0x0F4
> +#define LVTSSPARE2_0 0x0F8
> +#define LVTSSPARE3_0 0x0FC
> +#define THERMINTST 0xF04
> +
> +/* LVTS register mask */
> +#define THERMAL_COLD_INTERRUPT_0 BIT(0)
> +#define THERMAL_HOT_INTERRUPT_0 BIT(1)
> +#define THERMAL_LOW_OFFSET_INTERRUPT_0 BIT(2)
> +#define THERMAL_HIGH_OFFSET_INTERRUPT_0 BIT(3)
> +#define THERMAL_HOT2NORMAL_INTERRUPT_0 BIT(4)
> +#define THERMAL_COLD_INTERRUPT_1 BIT(5)
> +#define THERMAL_HOT_INTERRUPT_1 BIT(6)
> +#define THERMAL_LOW_OFFSET_INTERRUPT_1 BIT(7)
> +#define THERMAL_HIGH_OFFSET_INTERRUPT_1 BIT(8)
> +#define THERMAL_HOT2NORMAL_INTERRUPT_1 BIT(9)
> +#define THERMAL_COLD_INTERRUPT_2 BIT(10)
> +#define THERMAL_HOT_INTERRUPT_2 BIT(11)
> +#define THERMAL_LOW_OFFSET_INTERRUPT_2 BIT(12)
> +#define THERMAL_HIGH_OFFSET_INTERRUPT_2 BIT(13)
> +#define THERMAL_HOT2NORMAL_INTERRUPT_2 BIT(14)
> +#define THERMAL_AHB_TIMEOUT_INTERRUPT BIT(15)
> +#define THERMAL_DEVICE_TIMEOUT_INTERRUPT BIT(15)
> +#define THERMAL_IMMEDIATE_INTERRUPT_0 BIT(16)
> +#define THERMAL_IMMEDIATE_INTERRUPT_1 BIT(17)
> +#define THERMAL_IMMEDIATE_INTERRUPT_2 BIT(18)
> +#define THERMAL_FILTER_INTERRUPT_0 BIT(19)
> +#define THERMAL_FILTER_INTERRUPT_1 BIT(20)
> +#define THERMAL_FILTER_INTERRUPT_2 BIT(21)
> +#define THERMAL_COLD_INTERRUPT_3 BIT(22)
> +#define THERMAL_HOT_INTERRUPT_3 BIT(23)
> +#define THERMAL_LOW_OFFSET_INTERRUPT_3 BIT(24)
> +#define THERMAL_HIGH_OFFSET_INTERRUPT_3 BIT(25)
> +#define THERMAL_HOT2NORMAL_INTERRUPT_3 BIT(26)
> +#define THERMAL_IMMEDIATE_INTERRUPT_3 BIT(27)
> +#define THERMAL_FILTER_INTERRUPT_3 BIT(28)
> +#define THERMAL_PROTECTION_STAGE_1 BIT(29)
> +#define THERMAL_PROTECTION_STAGE_2 BIT(30)
> +#define THERMAL_PROTECTION_STAGE_3 BIT(31)
> +
> +#define CFG_REGISTER(reg, value) (reg << 8 | value)
> +#define STOP_COUNTING_V4 CFG_REGISTER(RG_TSFM_CTRL_0, 0x00)
> +#define SET_RG_TSFM_LPDLY_V4 CFG_REGISTER(RG_TSFM_CTRL_4, 0xA6)
> +#define SET_COUNTING_WINDOW_20US1_V4 CFG_REGISTER(RG_TSFM_CTRL_2, 0x00)
> +#define SET_COUNTING_WINDOW_20US2_V4 CFG_REGISTER(RG_TSFM_CTRL_1, 0x20)
> +#define TSV2F_CHOP_CKSEL_AND_TSV2F_EN_V4 CFG_REGISTER(RG_TSV2F_CTRL_2, 0x84)
> +#define TSBG_DEM_CKSEL_X_TSBG_CHOP_EN_V4 CFG_REGISTER(RG_TSV2F_CTRL_4, 0x7C)
> +#define SET_TS_RSV_V4 CFG_REGISTER(RG_TSV2F_CTRL_1, 0x8D)
> +#define SET_TS_EN_V4 CFG_REGISTER(RG_TSV2F_CTRL_0, 0xF4)
> +#define TOGGLE_RG_TSV2F_VCO_RST1_V4 CFG_REGISTER(RG_TSV2F_CTRL_0, 0xFC)
> +#define TOGGLE_RG_TSV2F_VCO_RST2_V4 CFG_REGISTER(RG_TSV2F_CTRL_0, 0xF4)
> +
> +#define SET_LVTS_AUTO_RCK_V4 CFG_REGISTER(RG_TSV2F_CTRL_6, 0x01)
> +#define SELECT_SENSOR_RCK_V4(id) CFG_REGISTER(RG_TSV2F_CTRL_5, (id))
> +#define SET_DEVICE_SINGLE_MODE_V4 CFG_REGISTER(RG_TSFM_CTRL_3, 0x78)
> +#define KICK_OFF_RCK_COUNTING_V4 CFG_REGISTER(RG_TSFM_CTRL_0, 0x02)
> +#define SET_SENSOR_NO_RCK_V4 CFG_REGISTER(RG_TSV2F_CTRL_5, 0x10)
> +#define SET_DEVICE_LOW_POWER_SINGLE_MODE_V4 CFG_REGISTER(RG_TSFM_CTRL_3, 0xB8)
> +
> +#define HAS_FEATURE(lvts_data, feature) (lvts_data->feature_bitmap & (feature))
> +#define GET_BASE_ADDR(lvts_data, tc_id) (lvts_data->base + lvts_data->tc[tc_id].addr_offset)
> +#define GET_CAL_DATA_BITMASK(index, lvts_data, h, l) (((index) < lvts_data->num_efuse_addr) ? \
> + ((lvts_data->efuse[(index)] & GENMASK(h, l)) >> l) : 0)
> +
> +#define GET_TC_SENSOR_NUM(lvts_data, tc_id) (lvts_data->tc[tc_id].num_sensor)
> +#define ONE_SAMPLE(lvts_data) (lvts_data->counting_window_us + 2 * BUS_ACCESS_US)
> +#define NUM_OF_SAMPLE(lvts_data, tc_id) ((lvts_data->tc[tc_id].hw_filter < LVTS_FILTER_2) ? \
> + LVTS_FILTER_SAMPLES_1 : ((lvts_data->tc[tc_id].hw_filter > LVTS_FILTER_16_OF_18) ? \
> + LVTS_FILTER_SAMPLES_1 : ((lvts_data->tc[tc_id].hw_filter == LVTS_FILTER_16_OF_18) ? \
> + LVTS_FILTER_SAMPLES_18 : ((lvts_data->tc[tc_id].hw_filter == LVTS_FILTER_8_OF_10) ? \
> + LVTS_FILTER_SAMPLES_10 : (lvts_data->tc[tc_id].hw_filter * 2)))))
> +
> +#define PERIOD_UNIT_US(lvts_data, tc_id) ((lvts_data->tc[tc_id].tc_speed->period_unit * 256 \
> + * CLOCK_26MHZ_CYCLE_NS) / 1000)
> +#define FILTER_INT_US(lvts_data, tc_id) (lvts_data->tc[tc_id].tc_speed->filter_interval_delay \
> + * PERIOD_UNIT_US(lvts_data, tc_id))
> +#define SENSOR_INT_US(lvts_data, tc_id) (lvts_data->tc[tc_id].tc_speed->sensor_interval_delay \
> + * PERIOD_UNIT_US(lvts_data, tc_id))
> +#define GROUP_INT_US(lvts_data, tc_id) (lvts_data->tc[tc_id].tc_speed->group_interval_delay \
> + * PERIOD_UNIT_US(lvts_data, tc_id))
> +#define SENSOR_LATENCY_US(lvts_data, tc_id) ((NUM_OF_SAMPLE(lvts_data, tc_id) - 1) * \
> + FILTER_INT_US(lvts_data, tc_id) + NUM_OF_SAMPLE(lvts_data, tc_id) * ONE_SAMPLE(lvts_data))
> +#define GROUP_LATENCY_US(lvts_data, tc_id) (GET_TC_SENSOR_NUM(lvts_data, tc_id) * \
> + SENSOR_LATENCY_US(lvts_data, tc_id) + (GET_TC_SENSOR_NUM(lvts_data, tc_id) - 1) * \
> + SENSOR_INT_US(lvts_data, tc_id) + GROUP_INT_US(lvts_data, tc_id))
> +
> +#define CK26M_ACTIVE(lvts_data) (((lvts_data->feature_bitmap & FEATURE_CK26M_ACTIVE) \
> + ? 1 : 0) << 30)
> +#define DEVICE_ACCESS (SCK_ONLY | DEVICE_ACCESS_STARTUS | READ_32BIT_ACCESS)
> +#define DEVICE_READ(lvts_data) (CK26M_ACTIVE(lvts_data) | DEVICE_ACCESS)
> +#define DEVICE_WRITE(lvts_data) (CK26M_ACTIVE(lvts_data) | DEVICE_ACCESS | WRITE_ACCESS)
> +#define RESET_ALL_DEVICES(lvts_data) (DEVICE_WRITE(lvts_data) | RG_TSFM_RST << 8 | 0xFF)
> +#define READ_DEVICE_REG(lvts_data, reg_id) (DEVICE_READ(lvts_data) | (reg_id) << 8 | 0x00)
> +#define READ_BACK_DEVICE_ID(lvts_data) (CK26M_ACTIVE(lvts_data) | DEVICE_ACCESS | \
> + BROADCAST_ID_UPDATE | RG_DID_LVTS << 8)
> +
> +/*
> + * LVTS HW filter settings
> + * 000: Get one sample
> + * 001: Get 2 samples and average them
> + * 010: Get 4 samples, drop max and min, then average the rest of 2 samples
> + * 011: Get 6 samples, drop max and min, then average the rest of 4 samples
> + * 100: Get 10 samples, drop max and min, then average the rest of 8 samples
> + * 101: Get 18 samples, drop max and min, then average the rest of 16 samples
> + */
> +enum lvts_hw_filter {
> + LVTS_FILTER_1,
> + LVTS_FILTER_2,
> + LVTS_FILTER_2_OF_4,
> + LVTS_FILTER_4_OF_6,
> + LVTS_FILTER_8_OF_10,
> + LVTS_FILTER_16_OF_18
> +};
> +
> +enum lvts_sensing_point {
> + SENSING_POINT0,
> + SENSING_POINT1,
> + SENSING_POINT2,
> + SENSING_POINT3,
> + ALL_SENSING_POINTS
> +};
> +
> +struct lvts_data;
> +
> +/**
> + * struct lvts_speed_settings - A structure to hold the data related to polling rate
> + * @period_unit: Period unit is a base for all interval delays
> + * @group_interval_delay: Delay between different rounds
> + * @filter_interval_delay: Delay between two samples of the same sensor
> + * @sensor_interval_delay: Delay between two samples of differnet sensors
> + *
> + * Calculation is achieved with the following equations:
> + * For the period unit: (period_us * 1000) / (256 * clock_26mhz_cycle_ns)
> + * For the interval delays: delay / period_us
> + */
> +struct lvts_speed_settings {
> + unsigned int period_unit;
> + unsigned int group_interval_delay;
> + unsigned int filter_interval_delay;
> + unsigned int sensor_interval_delay;
> +};
> +
> +struct lvts_tc_settings {
> + unsigned int dev_id;
> + unsigned int addr_offset;
> + unsigned int num_sensor;
> + unsigned int ts_offset;
> + unsigned int sensor_map[ALL_SENSING_POINTS]; /* In sensor ID */
> + struct lvts_speed_settings *tc_speed;
> + /*
> + * HW filter setting
> + * 000: Get one sample
> + * 001: Get 2 samples and average them
> + * 010: Get 4 samples, drop max and min, then average the rest of 2 samples
> + * 011: Get 6 samples, drop max and min, then average the rest of 4 samples
> + * 100: Get 10 samples, drop max and min, then average the rest of 8 samples
> + * 101: Get 18 samples, drop max and min, then average the rest of 16 samples
> + */
> + unsigned int hw_filter;
> + /*
> + * Dominator_sensing point is used to select a sensing point
> + * and reference its temperature to trigger Thermal HW Reboot
> + * When it is ALL_SENSING_POINTS, it will select all sensing points
> + */
> + int dominator_sensing_point;
> + int hw_reboot_trip_point; /* -274000: Disable HW reboot */
> + unsigned int irq_bit;
> +};
> +
> +struct lvts_formula_coeff {
> + int a;
> + int b;
> + unsigned int golden_temp;
> +};
> +
> +struct lvts_sensor_cal_data {
> + int use_fake_efuse; /* 1: Use fake efuse, 0: Use real efuse */
> + unsigned int golden_temp;
> + unsigned int *count_r;
> + unsigned int *count_rc;
> + unsigned int *count_rc_now;
> + unsigned int default_golden_temp;
> + unsigned int default_count_r;
> + unsigned int default_count_rc;
> +};
> +
> +struct platform_ops {
> + void (*efuse_to_cal_data)(struct lvts_data *lvts_data);
> + void (*device_enable_and_init)(struct lvts_data *lvts_data);
> + void (*device_enable_auto_rck)(struct lvts_data *lvts_data);
> + int (*device_read_count_rc_n)(struct lvts_data *lvts_data);
> + void (*set_cal_data)(struct lvts_data *lvts_data);
> + void (*init_controller)(struct lvts_data *lvts_data);
> +};
> +
> +struct lvts_data {
> + struct device *dev;
> + struct clk *clk;
> + void __iomem *base; /* LVTS base addresses */
> + unsigned int irq_num; /* LVTS interrupt numbers */
> + struct reset_control *reset;
> + int num_tc; /* Number of LVTS thermal controllers */
> + const struct lvts_tc_settings *tc;
> + int counting_window_us; /* LVTS device counting window */
> + int num_sensor; /* Number of sensors in this platform */
> + void __iomem **reg;
> + struct platform_ops ops;
> + int feature_bitmap; /* Show what features are enabled */
> + unsigned int num_efuse_addr;
> + unsigned int *efuse;
> + unsigned int num_efuse_block; /* Number of contiguous efuse indexes */
> + struct lvts_sensor_cal_data cal_data;
> + struct lvts_formula_coeff coeff;
> +};
> +
> +struct soc_temp_tz {
> + unsigned int id;
> + struct lvts_data *lvts_data;
> +};
> +
> +extern void lvts_device_enable_and_init(struct lvts_data *lvts_data);
> +extern void lvts_device_enable_auto_rck_v4(struct lvts_data *lvts_data);
> +extern int lvts_device_read_count_rc_n_v4(struct lvts_data *lvts_data);
> +extern void lvts_set_calibration_data_v4(struct lvts_data *lvts_data);
> +extern void lvts_init_controller_v4(struct lvts_data *lvts_data);
> +
> +extern int lvts_probe(struct platform_device *pdev);
> +extern int lvts_remove(struct platform_device *pdev);
> +extern int lvts_suspend(struct platform_device *pdev, pm_message_t state);
> +extern int lvts_resume(struct platform_device *pdev);
> +extern void lvts_shutdown(struct platform_device *pdev);
> +
> +#endif /* __MTK_SOC_TEMP_LVTS_H__ */
> diff --git a/drivers/thermal/mediatek/lvts_v4.c b/drivers/thermal/mediatek/lvts_v4.c
> new file mode 100644
> index 000000000000..3dc00d2589f9
> --- /dev/null
> +++ b/drivers/thermal/mediatek/lvts_v4.c
> @@ -0,0 +1,249 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (c) 2022 MediaTek Inc.
> + */
> +
> +#include <linux/of_irq.h>
> +#include <linux/platform_device.h>
> +#include "lvts_thermal.h"
> +
> +enum mt8192_lvts_mcu_sensor_enum {
> + MT8192_TS1_0,
> + MT8192_TS1_1,
> + MT8192_TS2_0,
> + MT8192_TS2_1,
> + MT8192_TS3_0,
> + MT8192_TS3_1,
> + MT8192_TS3_2,
> + MT8192_TS3_3,
> + MT8192_NUM_TS_MCU
> +};
> +
> +enum mt8192_lvts_ap_sensor_enum {
> + MT8192_TS4_0,
> + MT8192_TS4_1,
> + MT8192_TS5_0,
> + MT8192_TS5_1,
> + MT8192_TS6_0,
> + MT8192_TS6_1,
> + MT8192_TS7_0,
> + MT8192_TS7_1,
> + MT8192_TS7_2,
> + MT8192_NUM_TS_AP
> +};
> +
> +static void mt8192_mcu_efuse_to_cal_data(struct lvts_data *lvts_data)
> +{
> + const unsigned int mt8192_ts[] = { MT8192_TS2_0, MT8192_TS3_0 };
> + struct lvts_sensor_cal_data *cal_data = &lvts_data->cal_data;
> + unsigned int i, j;
> +
> + cal_data->golden_temp = GET_CAL_DATA_BITMASK(0, lvts_data, 31, 24);
> +
> + for (i = 0; i < MT8192_NUM_TS_MCU; i++)
> + cal_data->count_r[i] = GET_CAL_DATA_BITMASK(i + 1, lvts_data, 23, 0);
> +
> + cal_data->count_rc[MT8192_TS1_0] = GET_CAL_DATA_BITMASK(21, lvts_data, 23, 0);
> +
> + for (i = 0; i < (ARRAY_SIZE(mt8192_ts)); i++) {
> + for (j = 1; j <= 18; j++) {
> + cal_data->count_rc[mt8192_ts[i]] = (GET_CAL_DATA_BITMASK(j, lvts_data, 31, 24)
> + << 16) + (GET_CAL_DATA_BITMASK(j, lvts_data, 31, 24) << 8) +
> + GET_CAL_DATA_BITMASK(j, lvts_data, 31, 24);
> + }
> + }
> +}
> +
> +static void mt8192_ap_efuse_to_cal_data(struct lvts_data *lvts_data)
> +{
> + const unsigned int mt8192_ts[] = { MT8192_TS4_0, MT8192_TS5_0, MT8192_TS6_0, MT8192_TS7_0 };
> + struct lvts_sensor_cal_data *cal_data = &lvts_data->cal_data;
> + unsigned int i, j;
> +
> + cal_data->golden_temp = GET_CAL_DATA_BITMASK(0, lvts_data, 31, 24);
> +
> + for (i = 0; i < MT8192_NUM_TS_AP; i++)
> + cal_data->count_r[i] = GET_CAL_DATA_BITMASK(i + 1, lvts_data, 23, 0);
> +
> + for (i = 0; i < (ARRAY_SIZE(mt8192_ts)); i++) {
> + for (j = 1; j <= 18; j++) {
> + cal_data->count_rc[mt8192_ts[i]] = (GET_CAL_DATA_BITMASK(j, lvts_data, 31, 24)
> + << 16) + (GET_CAL_DATA_BITMASK(j, lvts_data, 31, 24) << 8) +
> + GET_CAL_DATA_BITMASK(j, lvts_data, 31, 24);
> + }
> + }
> +}
> +
> +static struct lvts_speed_settings tc_speed_mt8192 = {
> + .period_unit = PERIOD_UNIT,
> + .group_interval_delay = GROUP_INTERVAL_DELAY,
> + .filter_interval_delay = FILTER_INTERVAL_DELAY,
> + .sensor_interval_delay = SENSOR_INTERVAL_DELAY,
> +};
> +
> +static const struct lvts_tc_settings mt8192_tc_mcu_settings[] = {
> + [0] = {
> + .dev_id = 0x81,
> + .addr_offset = 0x0,
> + .num_sensor = 2,
> + .ts_offset = 0,
> + .sensor_map = { MT8192_TS1_0, MT8192_TS1_1 },
> + .tc_speed = &tc_speed_mt8192,
> + .hw_filter = LVTS_FILTER_2_OF_4,
> + .dominator_sensing_point = SENSING_POINT1,
> + .hw_reboot_trip_point = HW_REBOOT_TRIP_POINT,
> + .irq_bit = BIT(3),
> + },
> + [1] = {
> + .dev_id = 0x82,
> + .addr_offset = 0x100,
> + .num_sensor = 2,
> + .ts_offset = 0,
> + .sensor_map = { MT8192_TS2_0, MT8192_TS2_1 },
> + .tc_speed = &tc_speed_mt8192,
> + .hw_filter = LVTS_FILTER_2_OF_4,
> + .dominator_sensing_point = SENSING_POINT0,
> + .hw_reboot_trip_point = HW_REBOOT_TRIP_POINT,
> + .irq_bit = BIT(4),
> + },
> + [2] = {
> + .dev_id = 0x83,
> + .addr_offset = 0x200,
> + .num_sensor = 4,
> + .ts_offset = 0,
> + .sensor_map = { MT8192_TS3_0, MT8192_TS3_1, MT8192_TS3_2, MT8192_TS3_3 },
> + .tc_speed = &tc_speed_mt8192,
> + .hw_filter = LVTS_FILTER_2_OF_4,
> + .dominator_sensing_point = SENSING_POINT0,
> + .hw_reboot_trip_point = HW_REBOOT_TRIP_POINT,
> + .irq_bit = BIT(5),
> + }
> +};
> +
> +static const struct lvts_tc_settings mt8192_tc_ap_settings[] = {
> + [0] = {
> + .dev_id = 0x84,
> + .addr_offset = 0x0,
> + .num_sensor = 2,
> + .ts_offset = 0,
> + .sensor_map = { MT8192_TS4_0, MT8192_TS4_1 },
> + .tc_speed = &tc_speed_mt8192,
> + .hw_filter = LVTS_FILTER_2_OF_4,
> + .dominator_sensing_point = SENSING_POINT0,
> + .hw_reboot_trip_point = HW_REBOOT_TRIP_POINT,
> + .irq_bit = BIT(3),
> + },
> + [1] = {
> + .dev_id = 0x85,
> + .addr_offset = 0x100,
> + .num_sensor = 2,
> + .ts_offset = 0,
> + .sensor_map = { MT8192_TS5_0, MT8192_TS5_1 },
> + .tc_speed = &tc_speed_mt8192,
> + .hw_filter = LVTS_FILTER_2_OF_4,
> + .dominator_sensing_point = SENSING_POINT1,
> + .hw_reboot_trip_point = HW_REBOOT_TRIP_POINT,
> + .irq_bit = BIT(4),
> + },
> + [2] = {
> + .dev_id = 0x86,
> + .addr_offset = 0x200,
> + .num_sensor = 2,
> + .ts_offset = 0,
> + .sensor_map = { MT8192_TS6_0, MT8192_TS6_1 },
> + .tc_speed = &tc_speed_mt8192,
> + .hw_filter = LVTS_FILTER_2_OF_4,
> + .dominator_sensing_point = SENSING_POINT1,
> + .hw_reboot_trip_point = HW_REBOOT_TRIP_POINT,
> + .irq_bit = BIT(5),
> + },
> + [3] = {
> + .dev_id = 0x87,
> + .addr_offset = 0x300,
> + .num_sensor = 3,
> + .ts_offset = 0,
> + .sensor_map = { MT8192_TS7_0, MT8192_TS7_1, MT8192_TS7_2 },
> + .tc_speed = &tc_speed_mt8192,
> + .hw_filter = LVTS_FILTER_2_OF_4,
> + .dominator_sensing_point = SENSING_POINT2,
> + .hw_reboot_trip_point = HW_REBOOT_TRIP_POINT,
> + .irq_bit = BIT(6),
> + }
> +};
> +
> +static const struct lvts_data mt8192_lvts_mcu_data = {
> + .num_tc = (ARRAY_SIZE(mt8192_tc_mcu_settings)),
> + .tc = mt8192_tc_mcu_settings,
> + .num_sensor = MT8192_NUM_TS_MCU,
> + .ops = {
> + .efuse_to_cal_data = mt8192_mcu_efuse_to_cal_data,
> + .device_enable_and_init = lvts_device_enable_and_init,
> + .device_enable_auto_rck = lvts_device_enable_auto_rck_v4,
> + .device_read_count_rc_n = lvts_device_read_count_rc_n_v4,
> + .set_cal_data = lvts_set_calibration_data_v4,
> + .init_controller = lvts_init_controller_v4,
> + },
> + .feature_bitmap = FEATURE_DEVICE_AUTO_RCK,
> + .num_efuse_addr = NUM_EFUSE_ADDR,
> + .num_efuse_block = NUM_EFUSE_BLOCK_MT8192,
> + .cal_data = {
> + .default_golden_temp = DEFAULT_GOLDEN_TEMP,
> + .default_count_r = DEFAULT_CUONT_R,
> + .default_count_rc = DEFAULT_CUONT_RC,
> + },
> + .coeff = {
> + .a = COEFF_A,
> + .b = COEFF_B,
> + },
> +};
> +
> +static const struct lvts_data mt8192_lvts_ap_data = {
> + .num_tc = (ARRAY_SIZE(mt8192_tc_ap_settings)),
> + .tc = mt8192_tc_ap_settings,
> + .num_sensor = MT8192_NUM_TS_AP,
> + .ops = {
> + .efuse_to_cal_data = mt8192_ap_efuse_to_cal_data,
> + .device_enable_and_init = lvts_device_enable_and_init,
> + .device_enable_auto_rck = lvts_device_enable_auto_rck_v4,
> + .device_read_count_rc_n = lvts_device_read_count_rc_n_v4,
> + .set_cal_data = lvts_set_calibration_data_v4,
> + .init_controller = lvts_init_controller_v4,
> + },
> + .feature_bitmap = FEATURE_DEVICE_AUTO_RCK,
> + .num_efuse_addr = NUM_EFUSE_ADDR,
> + .num_efuse_block = NUM_EFUSE_BLOCK_MT8192,
> + .cal_data = {
> + .default_golden_temp = DEFAULT_GOLDEN_TEMP,
> + .default_count_r = DEFAULT_CUONT_R,
> + .default_count_rc = DEFAULT_CUONT_RC,
> + },
> + .coeff = {
> + .a = COEFF_A,
> + .b = COEFF_B,
> + },
> +};
> +
> +static const struct of_device_id lvts_of_match[] = {
> + { .compatible = "mediatek,mt8192-lvts-mcu", .data = &mt8192_lvts_mcu_data, },
> + { .compatible = "mediatek,mt8192-lvts-ap", .data = &mt8192_lvts_ap_data, },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, lvts_of_match);
> +
> +static struct platform_driver soc_temp_lvts = {
> + .probe = lvts_probe,
> + .remove = lvts_remove,
> + .suspend = lvts_suspend,
> + .resume = lvts_resume,
> + .shutdown = lvts_shutdown,
> + .driver = {
> + .name = "mtk-lvts-thermal-v4",
> + .of_match_table = lvts_of_match,
> + },
> +};
> +module_platform_driver(soc_temp_lvts);
> +
> +MODULE_AUTHOR("Yu-Chia Chang <ethan.chang at mediatek.com>");
> +MODULE_AUTHOR("Michael Kao <michael.kao at mediatek.com>");
> +MODULE_DESCRIPTION("MediaTek LVTS V4 Thermal Driver");
> +MODULE_LICENSE("GPL");
More information about the Linux-mediatek
mailing list