[PATCH v4 2/4] iommu/mediatek: Adjust mtk_iommu_config flow

[Chengci.Xu]

For reduce indention without functional change, prepare for MT8188.
If there are many port in a same larb, current flow will update
larb_mmu->mmu or update INFRA register for too many times.
So we save all port to portid_msk in the front of mtk_iommu_config(),
and then update only once for IOMMU configure. By this modification,
we can prevent MT8188 from sending to many SMC calls, avoiding enter
ATF for each port.

Signed-off-by: Chengci.Xu <chengci.xu at mediatek.com>
---
 drivers/iommu/mtk_iommu.c | 60 ++++++++++++++++++++++-----------------
 1 file changed, 34 insertions(+), 26 deletions(-)

diff --git a/drivers/iommu/mtk_iommu.c b/drivers/iommu/mtk_iommu.c
index 5a4e00e4bbbc..fbaf401f34e0 100644
--- a/drivers/iommu/mtk_iommu.c
+++ b/drivers/iommu/mtk_iommu.c
@@ -534,41 +534,49 @@ static int mtk_iommu_config(struct mtk_iommu_data *data, struct device *dev,
 	unsigned int                 larbid, portid;
 	struct iommu_fwspec *fwspec = dev_iommu_fwspec_get(dev);
 	const struct mtk_iommu_iova_region *region;
-	u32 peri_mmuen, peri_mmuen_msk;
+	unsigned long portid_msk_ext;
+	u32 portid_msk = 0;
 	int i, ret = 0;
 
 	for (i = 0; i < fwspec->num_ids; ++i) {
-		larbid = MTK_M4U_TO_LARB(fwspec->ids[i]);
 		portid = MTK_M4U_TO_PORT(fwspec->ids[i]);
+		portid_msk |= BIT(portid);
+	}
 
-		if (MTK_IOMMU_IS_TYPE(data->plat_data, MTK_IOMMU_TYPE_MM)) {
-			larb_mmu = &data->larb_imu[larbid];
+	if (MTK_IOMMU_IS_TYPE(data->plat_data, MTK_IOMMU_TYPE_MM)) {
+		/* All ports should be in the same larb. just use 0 here */
+		larbid = MTK_M4U_TO_LARB(fwspec->ids[0]);
+		larb_mmu = &data->larb_imu[larbid];
+		region = data->plat_data->iova_region + regionid;
 
-			region = data->plat_data->iova_region + regionid;
+		portid_msk_ext = portid_msk;
+		for_each_set_bit(portid, &portid_msk_ext, 32)
 			larb_mmu->bank[portid] = upper_32_bits(region->iova_base);
 
-			dev_dbg(dev, "%s iommu for larb(%s) port %d region %d rgn-bank %d.\n",
-				enable ? "enable" : "disable", dev_name(larb_mmu->dev),
-				portid, regionid, larb_mmu->bank[portid]);
-
-			if (enable)
-				larb_mmu->mmu |= MTK_SMI_MMU_EN(portid);
-			else
-				larb_mmu->mmu &= ~MTK_SMI_MMU_EN(portid);
-		} else if (MTK_IOMMU_IS_TYPE(data->plat_data, MTK_IOMMU_TYPE_INFRA)) {
-			peri_mmuen_msk = BIT(portid);
-			/* PCI dev has only one output id, enable the next writing bit for PCIe */
-			if (dev_is_pci(dev))
-				peri_mmuen_msk |= BIT(portid + 1);
-
-			peri_mmuen = enable ? peri_mmuen_msk : 0;
-			ret = regmap_update_bits(data->pericfg, PERICFG_IOMMU_1,
-						 peri_mmuen_msk, peri_mmuen);
-			if (ret)
-				dev_err(dev, "%s iommu(%s) inframaster 0x%x fail(%d).\n",
-					enable ? "enable" : "disable",
-					dev_name(data->dev), peri_mmuen_msk, ret);
+		dev_dbg(dev, "%s iommu for larb(%s) port 0x%x region %d rgn-bank %d.\n",
+			enable ? "enable" : "disable", dev_name(larb_mmu->dev),
+			portid_msk, regionid, upper_32_bits(region->iova_base));
+
+		if (enable)
+			larb_mmu->mmu |= portid_msk;
+		else
+			larb_mmu->mmu &= ~portid_msk;
+	} else if (MTK_IOMMU_IS_TYPE(data->plat_data, MTK_IOMMU_TYPE_INFRA)) {
+		/* PCI dev has only one output id, enable the next writing bit for PCIe */
+		if (dev_is_pci(dev)) {
+			if (fwspec->num_ids != 1) {
+				dev_err(dev, "PCI dev can only have one port.\n");
+				return -ENODEV;
+			}
+			portid_msk |= BIT(portid + 1);
 		}
+
+		ret = regmap_update_bits(data->pericfg, PERICFG_IOMMU_1,
+					 portid_msk, enable ? portid_msk : 0);
+		if (ret)
+			dev_err(dev, "%s iommu(%s) inframaster 0x%x fail(%d).\n",
+				enable ? "enable" : "disable",
+				dev_name(data->dev), portid_msk, ret);
 	}
 	return ret;
 }
-- 
2.25.1