[PATCH v3 4/7] dt-bindings: pinctrl: add bindings for Mediatek MT8365 SoC

[Krzysztof Kozlowski]

On 17/11/2022 22:03, Bernhard Rosenkränzer wrote:
> Add devicetree bindings for Mediatek MT8365 pinctrl driver.
> 
> Signed-off-by: Bernhard Rosenkränzer <bero at baylibre.com>

Thank you for your patch. There is something to discuss/improve.

> +
> +  pins-are-numbered:
> +    $ref: /schemas/types.yaml#/definitions/flag
> +    description: |
> +      Specify the subnodes are using numbered pinmux to specify pins.

Why would you name pins differently per board? And why this different
naming of the same pins is a property of hardware?

This looks like something to drop.

> +
> +  gpio-controller: true
> +
> +  "#gpio-cells":
> +    const: 2
> +    description: |
> +      Number of cells in GPIO specifier. Since the generic GPIO
> +      binding is used, the amount of cells must be specified as 2. See the below
> +      mentioned gpio binding representation for description of particular cells.
> +
> +  interrupt-controller: true
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  "#interrupt-cells":
> +    const: 2
> +
> +required:
> +  - compatible
> +  - reg
> +  - gpio-controller
> +  - "#gpio-cells"
> +
> +allOf:
> +  - $ref: pinctrl.yaml#
> +
> +patternProperties:

patternProperties go before "required:" block.

> +  '-pins$':
> +    type: object
> +    additionalProperties: false
> +    patternProperties:
> +      'pins':

How about anchoring it to either prefix or suffix? ^pins or pins$.

> +        type: object
> +        additionalProperties: false
> +        description: |
> +          A pinctrl node should contain at least one subnode representing the
> +          pinctrl groups available on the machine. Each subnode will list the
> +          pins it needs, and how they should be configured, with regard to muxer
> +          configuration, pullups, drive strength, input enable/disable and input
> +          schmitt.
> +        $ref: "/schemas/pinctrl/pincfg-node.yaml"

Drop quotes.

> +
> +        properties:
> +          pinmux:
> +            description:
> +              integer array, represents gpio pin number and mux setting.
> +              Supported pin number and mux varies for different SoCs, and are
> +              defined as macros in <soc>-pinfunc.h directly.
> +
> +          bias-disable: true
> +
> +          bias-pull-up:
> +            description: |
> +              Besides generic pinconfig options, it can be used as the pull up
> +              settings for 2 pull resistors, R0 and R1. User can configure those
> +              special pins.
> +
> +          bias-pull-down: true
> +
> +          input-enable: true
> +
> +          input-disable: true
> +
> +          output-low: true
> +
> +          output-high: true
> +
> +          input-schmitt-enable: true
> +
> +          input-schmitt-disable: true
> +
> +          mediatek,drive-strength-adv:
> +            description: |
> +              Describe the specific driving setup property.
> +              For I2C pins, the existing generic driving setup can only support
> +              2/4/6/8/10/12/14/16mA driving. But in specific driving setup, they
> +              can support 0.125/0.25/0.5/1mA adjustment. If we enable specific
> +              driving setup, the existing generic setup will be disabled.
> +              The specific driving setup is controlled by E1E0EN.
> +              When E1=0/E0=0, the strength is 0.125mA.
> +              When E1=0/E0=1, the strength is 0.25mA.
> +              When E1=1/E0=0, the strength is 0.5mA.
> +              When E1=1/E0=1, the strength is 1mA.
> +              EN is used to enable or disable the specific driving setup.
> +              Valid arguments are described as below:
> +              0: (E1, E0, EN) = (0, 0, 0)
> +              1: (E1, E0, EN) = (0, 0, 1)
> +              2: (E1, E0, EN) = (0, 1, 0)
> +              3: (E1, E0, EN) = (0, 1, 1)
> +              4: (E1, E0, EN) = (1, 0, 0)
> +              5: (E1, E0, EN) = (1, 0, 1)
> +              6: (E1, E0, EN) = (1, 1, 0)
> +              7: (E1, E0, EN) = (1, 1, 1)
> +              So the valid arguments are from 0 to 7.
> +            $ref: /schemas/types.yaml#/definitions/uint32
> +            enum: [0, 1, 2, 3, 4, 5, 6, 7]
> +
> +          mediatek,pull-up-adv:
> +            description: |
> +              Pull up setings for 2 pull resistors, R0 and R1. User can
> +              configure those special pins. Valid arguments are described as below:
> +              0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
> +              1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
> +              2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
> +              3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
> +            $ref: /schemas/types.yaml#/definitions/uint32
> +            enum: [0, 1, 2, 3]
> +
> +          mediatek,pull-down-adv:
> +            description: |
> +              Pull down settings for 2 pull resistors, R0 and R1. User can
> +              configure those special pins. Valid arguments are described as below:
> +              0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
> +              1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
> +              2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
> +              3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
> +            $ref: /schemas/types.yaml#/definitions/uint32
> +            enum: [0, 1, 2, 3]
> +
> +          mediatek,tdsel:
> +            description: |
> +              An integer describing the steps for output level shifter duty
> +              cycle when asserted (high pulse width adjustment). Valid arguments
> +              are from 0 to 15.
> +            $ref: /schemas/types.yaml#/definitions/uint32
> +
> +          mediatek,rdsel:
> +            description: |
> +              An integer describing the steps for input level shifter duty cycle
> +              when asserted (high pulse width adjustment). Valid arguments are
> +              from 0 to 63.
> +            $ref: /schemas/types.yaml#/definitions/uint32
> +
> +        required:
> +          - pinmux
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/pinctrl/mt8365-pinfunc.h>
> +    soc {
> +        #address-cells = <2>;
> +        #size-cells = <2>;
> +
> +        pio: pinctrl at 1000b000 {
> +          compatible = "mediatek,mt8365-pinctrl";
> +          reg = <0 0x1000b000 0 0x1000>;
> +          mediatek,pctl-regmap = <&syscfg_pctl>;
> +          pins-are-numbered;
> +          gpio-controller;
> +          #gpio-cells = <2>;
> +          interrupt-controller;
> +          #interrupt-cells = <2>;
> +          interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;

Blank line

> +          pio-pins {
> +            pins {
> +              pinmux = <MT8365_PIN_59_SDA1__FUNC_SDA1_0>, <MT8365_PIN_60_SCL1__FUNC_SCL1_0>;
> +              mediatek,pull-up-adv = <3>;
> +              mediatek,drive-strength-adv = <00>;
> +              bias-pull-up;
> +            };
> +          };
> +        };
> +    };

Best regards,
Krzysztof