[PATCH 2/2] iommu: mtk_iommu: Add support for MT6795 Helio X10 M4Us
AngeloGioacchino Del Regno
angelogioacchino.delregno at collabora.com
Tue May 17 02:26:47 PDT 2022
Il 17/05/22 11:08, Yong Wu ha scritto:
> On Fri, 2022-05-13 at 17:14 +0200, AngeloGioacchino Del Regno wrote:
>> Add support for the M4Us found in the MT6795 Helio X10 SoC.
>>
>> Signed-off-by: AngeloGioacchino Del Regno <
>> angelogioacchino.delregno at collabora.com>
>> ---
>> drivers/iommu/mtk_iommu.c | 20 +++++++++++++++++++-
>> 1 file changed, 19 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/iommu/mtk_iommu.c b/drivers/iommu/mtk_iommu.c
>> index 71b2ace74cd6..3d802dd3f377 100644
>> --- a/drivers/iommu/mtk_iommu.c
>> +++ b/drivers/iommu/mtk_iommu.c
>> @@ -157,6 +157,7 @@
>> enum mtk_iommu_plat {
>> M4U_MT2712,
>> M4U_MT6779,
>> + M4U_MT6795,
>> M4U_MT8167,
>> M4U_MT8173,
>> M4U_MT8183,
>> @@ -953,7 +954,8 @@ static int mtk_iommu_hw_init(const struct
>> mtk_iommu_data *data, unsigned int ban
>> * Global control settings are in bank0. May re-init these
>> global registers
>> * since no sure if there is bank0 consumers.
>> */
>> - if (data->plat_data->m4u_plat == M4U_MT8173) {
>> + if (data->plat_data->m4u_plat == M4U_MT6795 ||
>> + data->plat_data->m4u_plat == M4U_MT8173) {
>> regval = F_MMU_PREFETCH_RT_REPLACE_MOD |
>> F_MMU_TF_PROT_TO_PROGRAM_ADDR_MT8173;
>> } else {
>> @@ -1138,6 +1140,9 @@ static int mtk_iommu_probe(struct
>> platform_device *pdev)
>> case M4U_MT2712:
>> p = "mediatek,mt2712-infracfg";
>> break;
>> + case M4U_MT6795:
>> + p = "mediatek,mt6795-infracfg";
>> + break;
>> case M4U_MT8173:
>> p = "mediatek,mt8173-infracfg";
>> break;
>> @@ -1404,6 +1409,18 @@ static const struct mtk_iommu_plat_data
>> mt6779_data = {
>> .larbid_remap = {{0}, {1}, {2}, {3}, {5}, {7, 8}, {10}, {9}},
>> };
>>
>> +static const struct mtk_iommu_plat_data mt6795_data = {
>> + .m4u_plat = M4U_MT6795,
>> + .flags = HAS_4GB_MODE | HAS_BCLK | RESET_AXI |
>> + HAS_LEGACY_IVRP_PADDR | MTK_IOMMU_TYPE_MM,
>> + .inv_sel_reg = REG_MMU_INV_SEL_GEN1,
>> + .banks_num = 1,
>> + .banks_enable = {true},
>> + .iova_region = single_domain,
>> + .iova_region_nr = ARRAY_SIZE(single_domain),
>> + .larbid_remap = {{0}, {1}, {2}, {3}, {4}}, /* Linear mapping.
>> */
>> +};
>
> This is nearly same with mt8173_data. mt8173 has one more larb than
> mt6795, its larbid_remap is also ok for mt6795.
>
I think that we should be explicit about the larbid_remap property,
since mt6795 has one less larb, we should explicitly say that like
I did there... that's only for human readability I admit ... but,
still, I wouldn't want to see people thinking that MT6795 has 6 LARBs
because they've read that larbid_remap having 6 entries.
> thus it looks we could use mt8173 as the backward compatible.
> compatible = "mediatek,mt6795-m4u",
> "mediatek,mt8173-m4u";
>
> After this, the only thing is about "mediatek,mt6795-infracfg". we have
> to try again with mediatek,mt6795-infracfg after mediatek,mt8173-
> infracfg fail. I think we should allow the backward case in 4GB mode
> judgment if we have.
>
> What's your opinion? or some other suggestion?
> Thanks.
I know, I may have a plan for that, but I wanted to have a good reason to
propose such a thing, as if it's just about two SoCs needing that, there
would be no good reason to get things done differently.
...so, in order to provide a good cleanup, we have two possible roads to
follow here: either we add a generic "mediatek,infracfg" compatible to the
infra node (but I don't like that), or we can do it like it was previously
done in mtk-pm-domains.c (I prefer that approach):
iommu: iommu at somewhere {
... something ...
mediatek,infracfg = <&infracfg>;
};
infracfg = syscon_regmap_lookup_by_compatible(node, "mediatek,infracfg");
if (IS_ERR(infracfg)) {
/* try with the older way */
switch (...) {
case .... p = "mediatek,mt2712-infracfg";
... blah blah ...
}
/* legacy also failed, ouch! */
if (IS_ERR(infracfg))
return PTR_ERR(infracfg);
}
ret = regmap_read ... etc etc etc
Cheers,
Angelo
More information about the Linux-mediatek
mailing list