[PATCH v25 7/7] soc: mediatek: SVS: add mt8192 SVS GPU driver
Roger Lu
roger.lu at mediatek.com
Sun May 15 17:43:11 PDT 2022
mt8192 SVS GPU uses 2-line (high/low bank) HW architecture to provide
bank voltages. High bank helps update higher frequency's voltage
and low bank helps update lower frequency's voltage.
Signed-off-by: Roger Lu <roger.lu at mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno at collabora.com>
Reviewed-by: Kevin Hilman <khilman at baylibre.com>
---
drivers/soc/mediatek/mtk-svs.c | 473 ++++++++++++++++++++++++++++++++-
1 file changed, 468 insertions(+), 5 deletions(-)
diff --git a/drivers/soc/mediatek/mtk-svs.c b/drivers/soc/mediatek/mtk-svs.c
index aa0665725339..606a00a2e57d 100644
--- a/drivers/soc/mediatek/mtk-svs.c
+++ b/drivers/soc/mediatek/mtk-svs.c
@@ -24,6 +24,7 @@
#include <linux/pm_opp.h>
#include <linux/pm_runtime.h>
#include <linux/regulator/consumer.h>
+#include <linux/reset.h>
#include <linux/seq_file.h>
#include <linux/slab.h>
#include <linux/spinlock.h>
@@ -35,6 +36,10 @@
#define SVSB_CCI BIT(2)
#define SVSB_GPU BIT(3)
+/* svs bank 2-line type */
+#define SVSB_LOW BIT(8)
+#define SVSB_HIGH BIT(9)
+
/* svs bank mode support */
#define SVSB_MODE_ALL_DISABLE 0
#define SVSB_MODE_INIT01 BIT(1)
@@ -45,6 +50,8 @@
#define SVSB_INIT01_PD_REQ BIT(0)
#define SVSB_INIT01_VOLT_IGNORE BIT(1)
#define SVSB_INIT01_VOLT_INC_ONLY BIT(2)
+#define SVSB_MON_VOLT_IGNORE BIT(16)
+#define SVSB_REMOVE_DVTFIXED_VOLT BIT(24)
/* svs bank register common configuration */
#define SVSB_DET_MAX 0xffff
@@ -63,7 +70,9 @@
#define SVSB_RUNCONFIG_DEFAULT 0x80000000
/* svs bank related setting */
+#define BITS8 8
#define MAX_OPP_ENTRIES 16
+#define REG_BYTES 4
#define SVSB_DC_SIGNED_BIT BIT(15)
#define SVSB_DET_CLK_EN BIT(31)
#define SVSB_TEMP_LOWER_BOUND 0xb2
@@ -250,6 +259,7 @@ static const u32 svs_regs_v2[] = {
* @main_clk: main clock for svs bank
* @pbank: svs bank pointer needing to be protected by spin_lock section
* @banks: svs banks that svs platform supports
+ * @rst: svs platform reset control
* @efuse_parsing: svs platform efuse parsing function pointer
* @probe: svs platform probe function pointer
* @irqflags: svs platform irq settings flags
@@ -267,6 +277,7 @@ struct svs_platform {
struct clk *main_clk;
struct svs_bank *pbank;
struct svs_bank *banks;
+ struct reset_control *rst;
bool (*efuse_parsing)(struct svs_platform *svsp);
int (*probe)(struct svs_platform *svsp);
unsigned long irqflags;
@@ -307,6 +318,7 @@ struct svs_platform_data {
* @pm_runtime_enabled_count: bank pm runtime enabled count
* @mode_support: bank mode support.
* @freq_base: reference frequency for bank init
+ * @turn_freq_base: refenrece frequency for 2-line turn point
* @vboot: voltage request for bank init01 only
* @opp_dfreq: default opp frequency table
* @opp_dvolt: default opp voltage table
@@ -342,6 +354,8 @@ struct svs_platform_data {
* @mtdes: svs efuse data
* @dcbdet: svs efuse data
* @dcmdet: svs efuse data
+ * @turn_pt: 2-line turn point tells which opp_volt calculated by high/low bank
+ * @type: bank type to represent it is 2-line (high/low) bank or 1-line bank
*
* Svs bank will generate suitalbe voltages by below general math equation
* and provide these voltages to opp voltage table.
@@ -366,6 +380,7 @@ struct svs_bank {
u32 pm_runtime_enabled_count;
u32 mode_support;
u32 freq_base;
+ u32 turn_freq_base;
u32 vboot;
u32 opp_dfreq[MAX_OPP_ENTRIES];
u32 opp_dvolt[MAX_OPP_ENTRIES];
@@ -401,6 +416,8 @@ struct svs_bank {
u32 mtdes;
u32 dcbdet;
u32 dcmdet;
+ u32 turn_pt;
+ u32 type;
};
static u32 percent(u32 numerator, u32 denominator)
@@ -436,13 +453,59 @@ static u32 svs_bank_volt_to_opp_volt(u32 svsb_volt, u32 svsb_volt_step,
return (svsb_volt * svsb_volt_step) + svsb_volt_base;
}
+static u32 svs_opp_volt_to_bank_volt(u32 opp_u_volt, u32 svsb_volt_step,
+ u32 svsb_volt_base)
+{
+ return (opp_u_volt - svsb_volt_base) / svsb_volt_step;
+}
+
+static int svs_sync_bank_volts_from_opp(struct svs_bank *svsb)
+{
+ struct dev_pm_opp *opp;
+ u32 i, opp_u_volt;
+
+ for (i = 0; i < svsb->opp_count; i++) {
+ opp = dev_pm_opp_find_freq_exact(svsb->opp_dev,
+ svsb->opp_dfreq[i],
+ true);
+ if (IS_ERR(opp)) {
+ dev_err(svsb->dev, "cannot find freq = %u (%ld)\n",
+ svsb->opp_dfreq[i], PTR_ERR(opp));
+ return PTR_ERR(opp);
+ }
+
+ opp_u_volt = dev_pm_opp_get_voltage(opp);
+ svsb->volt[i] = svs_opp_volt_to_bank_volt(opp_u_volt,
+ svsb->volt_step,
+ svsb->volt_base);
+ dev_pm_opp_put(opp);
+ }
+
+ return 0;
+}
+
static int svs_adjust_pm_opp_volts(struct svs_bank *svsb)
{
int ret = -EPERM, tzone_temp = 0;
- u32 i, svsb_volt, opp_volt, temp_voffset = 0;
+ u32 i, svsb_volt, opp_volt, temp_voffset = 0, opp_start, opp_stop;
mutex_lock(&svsb->lock);
+ /*
+ * 2-line bank updates its corresponding opp volts.
+ * 1-line bank updates all opp volts.
+ */
+ if (svsb->type == SVSB_HIGH) {
+ opp_start = 0;
+ opp_stop = svsb->turn_pt;
+ } else if (svsb->type == SVSB_LOW) {
+ opp_start = svsb->turn_pt;
+ opp_stop = svsb->opp_count;
+ } else {
+ opp_start = 0;
+ opp_stop = svsb->opp_count;
+ }
+
/* Get thermal effect */
if (svsb->phase == SVSB_PHASE_MON) {
ret = thermal_zone_get_temp(svsb->tzd, &tzone_temp);
@@ -457,10 +520,16 @@ static int svs_adjust_pm_opp_volts(struct svs_bank *svsb)
temp_voffset += svsb->tzone_htemp_voffset;
else if (tzone_temp <= svsb->tzone_ltemp)
temp_voffset += svsb->tzone_ltemp_voffset;
+
+ /* 2-line bank update all opp volts when running mon mode */
+ if (svsb->type == SVSB_HIGH || svsb->type == SVSB_LOW) {
+ opp_start = 0;
+ opp_stop = svsb->opp_count;
+ }
}
/* vmin <= svsb_volt (opp_volt) <= default opp voltage */
- for (i = 0; i < svsb->opp_count; i++) {
+ for (i = opp_start; i < opp_stop; i++) {
switch (svsb->phase) {
case SVSB_PHASE_ERROR:
opp_volt = svsb->opp_dvolt[i];
@@ -623,9 +692,11 @@ static int svs_status_debug_show(struct seq_file *m, void *v)
ret = thermal_zone_get_temp(svsb->tzd, &tzone_temp);
if (ret)
- seq_printf(m, "%s: temperature ignore\n", svsb->name);
+ seq_printf(m, "%s: temperature ignore, turn_pt = %u\n",
+ svsb->name, svsb->turn_pt);
else
- seq_printf(m, "%s: temperature = %d\n", svsb->name, tzone_temp);
+ seq_printf(m, "%s: temperature = %d, turn_pt = %u\n",
+ svsb->name, tzone_temp, svsb->turn_pt);
for (i = 0; i < svsb->opp_count; i++) {
opp = dev_pm_opp_find_freq_exact(svsb->opp_dev,
@@ -731,6 +802,181 @@ static u32 interpolate(u32 f0, u32 f1, u32 v0, u32 v1, u32 fx)
return DIV_ROUND_UP(vx, 100);
}
+static void svs_get_bank_volts_v3(struct svs_platform *svsp)
+{
+ struct svs_bank *svsb = svsp->pbank;
+ u32 i, j, *vop, vop74, vop30, turn_pt = svsb->turn_pt;
+ u32 b_sft, shift_byte = 0, opp_start = 0, opp_stop = 0;
+ u32 middle_index = (svsb->opp_count / 2);
+
+ if (svsb->phase == SVSB_PHASE_MON &&
+ svsb->volt_flags & SVSB_MON_VOLT_IGNORE)
+ return;
+
+ vop74 = svs_readl_relaxed(svsp, VOP74);
+ vop30 = svs_readl_relaxed(svsp, VOP30);
+
+ /* Target is to set svsb->volt[] by algorithm */
+ if (turn_pt < middle_index) {
+ if (svsb->type == SVSB_HIGH) {
+ /* volt[0] ~ volt[turn_pt - 1] */
+ for (i = 0; i < turn_pt; i++) {
+ b_sft = BITS8 * (shift_byte % REG_BYTES);
+ vop = (shift_byte < REG_BYTES) ? &vop30 :
+ &vop74;
+ svsb->volt[i] = (*vop >> b_sft) & GENMASK(7, 0);
+ shift_byte++;
+ }
+ } else if (svsb->type == SVSB_LOW) {
+ /* volt[turn_pt] + volt[j] ~ volt[opp_count - 1] */
+ j = svsb->opp_count - 7;
+ svsb->volt[turn_pt] = vop30 & GENMASK(7, 0);
+ shift_byte++;
+ for (i = j; i < svsb->opp_count; i++) {
+ b_sft = BITS8 * (shift_byte % REG_BYTES);
+ vop = (shift_byte < REG_BYTES) ? &vop30 :
+ &vop74;
+ svsb->volt[i] = (*vop >> b_sft) & GENMASK(7, 0);
+ shift_byte++;
+ }
+
+ /* volt[turn_pt + 1] ~ volt[j - 1] by interpolate */
+ for (i = turn_pt + 1; i < j; i++)
+ svsb->volt[i] = interpolate(svsb->freq_pct[turn_pt],
+ svsb->freq_pct[j],
+ svsb->volt[turn_pt],
+ svsb->volt[j],
+ svsb->freq_pct[i]);
+ }
+ } else {
+ if (svsb->type == SVSB_HIGH) {
+ /* volt[0] + volt[j] ~ volt[turn_pt - 1] */
+ j = turn_pt - 7;
+ svsb->volt[0] = vop30 & GENMASK(7, 0);
+ shift_byte++;
+ for (i = j; i < turn_pt; i++) {
+ b_sft = BITS8 * (shift_byte % REG_BYTES);
+ vop = (shift_byte < REG_BYTES) ? &vop30 :
+ &vop74;
+ svsb->volt[i] = (*vop >> b_sft) & GENMASK(7, 0);
+ shift_byte++;
+ }
+
+ /* volt[1] ~ volt[j - 1] by interpolate */
+ for (i = 1; i < j; i++)
+ svsb->volt[i] = interpolate(svsb->freq_pct[0],
+ svsb->freq_pct[j],
+ svsb->volt[0],
+ svsb->volt[j],
+ svsb->freq_pct[i]);
+ } else if (svsb->type == SVSB_LOW) {
+ /* volt[turn_pt] ~ volt[opp_count - 1] */
+ for (i = turn_pt; i < svsb->opp_count; i++) {
+ b_sft = BITS8 * (shift_byte % REG_BYTES);
+ vop = (shift_byte < REG_BYTES) ? &vop30 :
+ &vop74;
+ svsb->volt[i] = (*vop >> b_sft) & GENMASK(7, 0);
+ shift_byte++;
+ }
+ }
+ }
+
+ if (svsb->type == SVSB_HIGH) {
+ opp_start = 0;
+ opp_stop = svsb->turn_pt;
+ } else if (svsb->type == SVSB_LOW) {
+ opp_start = svsb->turn_pt;
+ opp_stop = svsb->opp_count;
+ }
+
+ for (i = opp_start; i < opp_stop; i++)
+ if (svsb->volt_flags & SVSB_REMOVE_DVTFIXED_VOLT)
+ svsb->volt[i] -= svsb->dvt_fixed;
+}
+
+static void svs_set_bank_freq_pct_v3(struct svs_platform *svsp)
+{
+ struct svs_bank *svsb = svsp->pbank;
+ u32 i, j, *freq_pct, freq_pct74 = 0, freq_pct30 = 0;
+ u32 b_sft, shift_byte = 0, turn_pt;
+ u32 middle_index = (svsb->opp_count / 2);
+
+ for (i = 0; i < svsb->opp_count; i++) {
+ if (svsb->opp_dfreq[i] <= svsb->turn_freq_base) {
+ svsb->turn_pt = i;
+ break;
+ }
+ }
+
+ turn_pt = svsb->turn_pt;
+
+ /* Target is to fill out freq_pct74 / freq_pct30 by algorithm */
+ if (turn_pt < middle_index) {
+ if (svsb->type == SVSB_HIGH) {
+ /*
+ * If we don't handle this situation,
+ * SVSB_HIGH's FREQPCT74 / FREQPCT30 would keep "0"
+ * and this leads SVSB_LOW to work abnormally.
+ */
+ if (turn_pt == 0)
+ freq_pct30 = svsb->freq_pct[0];
+
+ /* freq_pct[0] ~ freq_pct[turn_pt - 1] */
+ for (i = 0; i < turn_pt; i++) {
+ b_sft = BITS8 * (shift_byte % REG_BYTES);
+ freq_pct = (shift_byte < REG_BYTES) ?
+ &freq_pct30 : &freq_pct74;
+ *freq_pct |= (svsb->freq_pct[i] << b_sft);
+ shift_byte++;
+ }
+ } else if (svsb->type == SVSB_LOW) {
+ /*
+ * freq_pct[turn_pt] +
+ * freq_pct[opp_count - 7] ~ freq_pct[opp_count -1]
+ */
+ freq_pct30 = svsb->freq_pct[turn_pt];
+ shift_byte++;
+ j = svsb->opp_count - 7;
+ for (i = j; i < svsb->opp_count; i++) {
+ b_sft = BITS8 * (shift_byte % REG_BYTES);
+ freq_pct = (shift_byte < REG_BYTES) ?
+ &freq_pct30 : &freq_pct74;
+ *freq_pct |= (svsb->freq_pct[i] << b_sft);
+ shift_byte++;
+ }
+ }
+ } else {
+ if (svsb->type == SVSB_HIGH) {
+ /*
+ * freq_pct[0] +
+ * freq_pct[turn_pt - 7] ~ freq_pct[turn_pt - 1]
+ */
+ freq_pct30 = svsb->freq_pct[0];
+ shift_byte++;
+ j = turn_pt - 7;
+ for (i = j; i < turn_pt; i++) {
+ b_sft = BITS8 * (shift_byte % REG_BYTES);
+ freq_pct = (shift_byte < REG_BYTES) ?
+ &freq_pct30 : &freq_pct74;
+ *freq_pct |= (svsb->freq_pct[i] << b_sft);
+ shift_byte++;
+ }
+ } else if (svsb->type == SVSB_LOW) {
+ /* freq_pct[turn_pt] ~ freq_pct[opp_count - 1] */
+ for (i = turn_pt; i < svsb->opp_count; i++) {
+ b_sft = BITS8 * (shift_byte % REG_BYTES);
+ freq_pct = (shift_byte < REG_BYTES) ?
+ &freq_pct30 : &freq_pct74;
+ *freq_pct |= (svsb->freq_pct[i] << b_sft);
+ shift_byte++;
+ }
+ }
+ }
+
+ svs_writel_relaxed(svsp, freq_pct74, FREQPCT74);
+ svs_writel_relaxed(svsp, freq_pct30, FREQPCT30);
+}
+
static void svs_get_bank_volts_v2(struct svs_platform *svsp)
{
struct svs_bank *svsb = svsp->pbank;
@@ -1174,6 +1420,25 @@ static int svs_init02(struct svs_platform *svsp)
}
}
+ /*
+ * 2-line high/low bank update its corresponding opp voltages only.
+ * Therefore, we sync voltages from opp for high/low bank voltages
+ * consistency.
+ */
+ for (idx = 0; idx < svsp->bank_max; idx++) {
+ svsb = &svsp->banks[idx];
+
+ if (!(svsb->mode_support & SVSB_MODE_INIT02))
+ continue;
+
+ if (svsb->type == SVSB_HIGH || svsb->type == SVSB_LOW) {
+ if (svs_sync_bank_volts_from_opp(svsb)) {
+ dev_err(svsb->dev, "sync volt fail\n");
+ return -EPERM;
+ }
+ }
+ }
+
return 0;
}
@@ -1218,6 +1483,7 @@ static int svs_suspend(struct device *dev)
struct svs_platform *svsp = dev_get_drvdata(dev);
struct svs_bank *svsb;
unsigned long flags;
+ int ret;
u32 idx;
for (idx = 0; idx < svsp->bank_max; idx++) {
@@ -1235,6 +1501,12 @@ static int svs_suspend(struct device *dev)
svs_adjust_pm_opp_volts(svsb);
}
+ ret = reset_control_assert(svsp->rst);
+ if (ret) {
+ dev_err(svsp->dev, "cannot assert reset %d\n", ret);
+ return ret;
+ }
+
clk_disable_unprepare(svsp->main_clk);
return 0;
@@ -1251,6 +1523,12 @@ static int svs_resume(struct device *dev)
return ret;
}
+ ret = reset_control_deassert(svsp->rst);
+ if (ret) {
+ dev_err(svsp->dev, "cannot deassert reset %d\n", ret);
+ return ret;
+ }
+
ret = svs_init02(svsp);
if (ret)
return ret;
@@ -1284,7 +1562,12 @@ static int svs_bank_resource_setup(struct svs_platform *svsp)
svsb->name = "SVSB_CCI";
break;
case SVSB_GPU:
- svsb->name = "SVSB_GPU";
+ if (svsb->type == SVSB_HIGH)
+ svsb->name = "SVSB_GPU_HIGH";
+ else if (svsb->type == SVSB_LOW)
+ svsb->name = "SVSB_GPU_LOW";
+ else
+ svsb->name = "SVSB_GPU";
break;
default:
dev_err(svsb->dev, "unknown sw_id: %u\n", svsb->sw_id);
@@ -1357,6 +1640,85 @@ static int svs_bank_resource_setup(struct svs_platform *svsp)
return 0;
}
+static bool svs_mt8192_efuse_parsing(struct svs_platform *svsp)
+{
+ struct svs_bank *svsb;
+ struct nvmem_cell *cell;
+ u32 idx, i, vmin, golden_temp;
+
+ for (i = 0; i < svsp->efuse_max; i++)
+ if (svsp->efuse[i])
+ dev_info(svsp->dev, "M_HW_RES%d: 0x%08x\n",
+ i, svsp->efuse[i]);
+
+ if (!svsp->efuse[9]) {
+ dev_notice(svsp->dev, "svs_efuse[9] = 0x0?\n");
+ return false;
+ }
+
+ /* Svs efuse parsing */
+ vmin = (svsp->efuse[19] >> 4) & GENMASK(1, 0);
+
+ for (idx = 0; idx < svsp->bank_max; idx++) {
+ svsb = &svsp->banks[idx];
+
+ if (vmin == 0x1)
+ svsb->vmin = 0x1e;
+
+ if (svsb->type == SVSB_LOW) {
+ svsb->mtdes = svsp->efuse[10] & GENMASK(7, 0);
+ svsb->bdes = (svsp->efuse[10] >> 16) & GENMASK(7, 0);
+ svsb->mdes = (svsp->efuse[10] >> 24) & GENMASK(7, 0);
+ svsb->dcbdet = (svsp->efuse[17]) & GENMASK(7, 0);
+ svsb->dcmdet = (svsp->efuse[17] >> 8) & GENMASK(7, 0);
+ } else if (svsb->type == SVSB_HIGH) {
+ svsb->mtdes = svsp->efuse[9] & GENMASK(7, 0);
+ svsb->bdes = (svsp->efuse[9] >> 16) & GENMASK(7, 0);
+ svsb->mdes = (svsp->efuse[9] >> 24) & GENMASK(7, 0);
+ svsb->dcbdet = (svsp->efuse[17] >> 16) & GENMASK(7, 0);
+ svsb->dcmdet = (svsp->efuse[17] >> 24) & GENMASK(7, 0);
+ }
+
+ svsb->vmax += svsb->dvt_fixed;
+ }
+
+ /* Thermal efuse parsing */
+ cell = nvmem_cell_get(svsp->dev, "t-calibration-data");
+ if (IS_ERR_OR_NULL(cell)) {
+ dev_err(svsp->dev, "no \"t-calibration-data\"? %ld\n",
+ PTR_ERR(cell));
+ return false;
+ }
+
+ svsp->tefuse = nvmem_cell_read(cell, &svsp->tefuse_max);
+ if (IS_ERR(svsp->tefuse)) {
+ dev_err(svsp->dev, "cannot read thermal efuse: %ld\n",
+ PTR_ERR(svsp->tefuse));
+ nvmem_cell_put(cell);
+ return false;
+ }
+
+ svsp->tefuse_max /= sizeof(u32);
+ nvmem_cell_put(cell);
+
+ for (i = 0; i < svsp->tefuse_max; i++)
+ if (svsp->tefuse[i] != 0)
+ break;
+
+ if (i == svsp->tefuse_max)
+ golden_temp = 50; /* All thermal efuse data are 0 */
+ else
+ golden_temp = (svsp->tefuse[0] >> 24) & GENMASK(7, 0);
+
+ for (idx = 0; idx < svsp->bank_max; idx++) {
+ svsb = &svsp->banks[idx];
+ svsb->mts = 500;
+ svsb->bts = (((500 * golden_temp + 250460) / 1000) - 25) * 4;
+ }
+
+ return true;
+}
+
static bool svs_mt8183_efuse_parsing(struct svs_platform *svsp)
{
struct svs_bank *svsb;
@@ -1642,6 +2004,39 @@ static struct device *svs_add_device_link(struct svs_platform *svsp,
return dev;
}
+static int svs_mt8192_platform_probe(struct svs_platform *svsp)
+{
+ struct device *dev;
+ struct svs_bank *svsb;
+ u32 idx;
+
+ svsp->rst = devm_reset_control_get_optional(svsp->dev, "svs_rst");
+ if (IS_ERR(svsp->rst))
+ return dev_err_probe(svsp->dev, PTR_ERR(svsp->rst),
+ "cannot get svs reset control\n");
+
+ dev = svs_add_device_link(svsp, "lvts");
+ if (IS_ERR(dev))
+ return dev_err_probe(svsp->dev, PTR_ERR(dev),
+ "failed to get lvts device\n");
+
+ for (idx = 0; idx < svsp->bank_max; idx++) {
+ svsb = &svsp->banks[idx];
+
+ if (svsb->type == SVSB_HIGH)
+ svsb->opp_dev = svs_add_device_link(svsp, "mali");
+ else if (svsb->type == SVSB_LOW)
+ svsb->opp_dev = svs_get_subsys_device(svsp, "mali");
+
+ if (IS_ERR(svsb->opp_dev))
+ return dev_err_probe(svsp->dev, PTR_ERR(svsb->opp_dev),
+ "failed to get OPP device for bank %d\n",
+ idx);
+ }
+
+ return 0;
+}
+
static int svs_mt8183_platform_probe(struct svs_platform *svsp)
{
struct device *dev;
@@ -1681,6 +2076,61 @@ static int svs_mt8183_platform_probe(struct svs_platform *svsp)
return 0;
}
+static struct svs_bank svs_mt8192_banks[] = {
+ {
+ .sw_id = SVSB_GPU,
+ .type = SVSB_LOW,
+ .set_freq_pct = svs_set_bank_freq_pct_v3,
+ .get_volts = svs_get_bank_volts_v3,
+ .volt_flags = SVSB_REMOVE_DVTFIXED_VOLT,
+ .mode_support = SVSB_MODE_INIT02,
+ .opp_count = MAX_OPP_ENTRIES,
+ .freq_base = 688000000,
+ .turn_freq_base = 688000000,
+ .volt_step = 6250,
+ .volt_base = 400000,
+ .vmax = 0x60,
+ .vmin = 0x1a,
+ .age_config = 0x555555,
+ .dc_config = 0x1,
+ .dvt_fixed = 0x1,
+ .vco = 0x18,
+ .chk_shift = 0x87,
+ .core_sel = 0x0fff0100,
+ .int_st = BIT(0),
+ .ctl0 = 0x00540003,
+ },
+ {
+ .sw_id = SVSB_GPU,
+ .type = SVSB_HIGH,
+ .set_freq_pct = svs_set_bank_freq_pct_v3,
+ .get_volts = svs_get_bank_volts_v3,
+ .tzone_name = "gpu1",
+ .volt_flags = SVSB_REMOVE_DVTFIXED_VOLT |
+ SVSB_MON_VOLT_IGNORE,
+ .mode_support = SVSB_MODE_INIT02 | SVSB_MODE_MON,
+ .opp_count = MAX_OPP_ENTRIES,
+ .freq_base = 902000000,
+ .turn_freq_base = 688000000,
+ .volt_step = 6250,
+ .volt_base = 400000,
+ .vmax = 0x60,
+ .vmin = 0x1a,
+ .age_config = 0x555555,
+ .dc_config = 0x1,
+ .dvt_fixed = 0x6,
+ .vco = 0x18,
+ .chk_shift = 0x87,
+ .core_sel = 0x0fff0101,
+ .int_st = BIT(1),
+ .ctl0 = 0x00540003,
+ .tzone_htemp = 85000,
+ .tzone_htemp_voffset = 0,
+ .tzone_ltemp = 25000,
+ .tzone_ltemp_voffset = 7,
+ },
+};
+
static struct svs_bank svs_mt8183_banks[] = {
{
.sw_id = SVSB_CPU_LITTLE,
@@ -1785,6 +2235,16 @@ static struct svs_bank svs_mt8183_banks[] = {
},
};
+static const struct svs_platform_data svs_mt8192_platform_data = {
+ .name = "mt8192-svs",
+ .banks = svs_mt8192_banks,
+ .efuse_parsing = svs_mt8192_efuse_parsing,
+ .probe = svs_mt8192_platform_probe,
+ .irqflags = IRQF_TRIGGER_HIGH,
+ .regs = svs_regs_v2,
+ .bank_max = ARRAY_SIZE(svs_mt8192_banks),
+};
+
static const struct svs_platform_data svs_mt8183_platform_data = {
.name = "mt8183-svs",
.banks = svs_mt8183_banks,
@@ -1797,6 +2257,9 @@ static const struct svs_platform_data svs_mt8183_platform_data = {
static const struct of_device_id svs_of_match[] = {
{
+ .compatible = "mediatek,mt8192-svs",
+ .data = &svs_mt8192_platform_data,
+ }, {
.compatible = "mediatek,mt8183-svs",
.data = &svs_mt8183_platform_data,
}, {
--
2.18.0
More information about the Linux-mediatek
mailing list