[PATCH v5, 4/5] drm/mediatek: keep dsi as LP00 before dcs cmds transfer

xinlei.lee at mediatek.com xinlei.lee at mediatek.com
Tue May 10 19:36:35 PDT 2022


From: Jitao Shi <jitao.shi at mediatek.com>

To comply with the panel sequence, hold the mipi signal to LP00 before the dcs cmds transmission,
and pull the mipi signal high from LP00 to LP11 until the start of the dcs cmds transmission.
The normal panel timing is :
(1) pp1800 DC pull up
(2) avdd & avee AC pull high
(3) lcm_reset pull high -> pull low -> pull high
(4) Pull MIPI signal high (LP11) -> initial code -> send video data(HS mode)
The power-off sequence is reversed.
If dsi is not in cmd mode, then dsi will pull the mipi signal high in the mtk_output_dsi_enable function.
The delay in lane_ready func is the reaction time of dsi_rx after pulling up the mipi signal.

Fixes: 2dd8075d2185 ("drm/mediatek: mtk_dsi: Use the drm_panel_bridge API")

Signed-off-by: Jitao Shi <jitao.shi at mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee at mediatek.com>
---
 drivers/gpu/drm/mediatek/mtk_dsi.c | 29 ++++++++++++++++++++++-------
 1 file changed, 22 insertions(+), 7 deletions(-)

diff --git a/drivers/gpu/drm/mediatek/mtk_dsi.c b/drivers/gpu/drm/mediatek/mtk_dsi.c
index 2dee6632a541..98b7811502e7 100644
--- a/drivers/gpu/drm/mediatek/mtk_dsi.c
+++ b/drivers/gpu/drm/mediatek/mtk_dsi.c
@@ -203,6 +203,7 @@ struct mtk_dsi {
 	struct mtk_phy_timing phy_timing;
 	int refcount;
 	bool enabled;
+	bool lanes_ready;
 	u32 irq_data;
 	wait_queue_head_t irq_wait_queue;
 	const struct mtk_dsi_driver_data *driver_data;
@@ -666,13 +667,6 @@ static int mtk_dsi_poweron(struct mtk_dsi *dsi)
 	mtk_dsi_config_vdo_timing(dsi);
 	mtk_dsi_set_interrupt_enable(dsi);
 
-	mtk_dsi_rxtx_control(dsi);
-	usleep_range(30, 100);
-	mtk_dsi_reset_dphy(dsi);
-	mtk_dsi_clk_ulp_mode_leave(dsi);
-	mtk_dsi_lane0_ulp_mode_leave(dsi);
-	mtk_dsi_clk_hs_mode(dsi, 0);
-
 	return 0;
 err_disable_engine_clk:
 	clk_disable_unprepare(dsi->engine_clk);
@@ -701,6 +695,24 @@ static void mtk_dsi_poweroff(struct mtk_dsi *dsi)
 	clk_disable_unprepare(dsi->digital_clk);
 
 	phy_power_off(dsi->phy);
+
+	dsi->lanes_ready = false;
+
+}
+
+static void mtk_dsi_lane_ready(struct mtk_dsi *dsi)
+{
+	if (!dsi->lanes_ready) {
+		dsi->lanes_ready = true;
+		mtk_dsi_rxtx_control(dsi);
+		usleep_range(30, 100);
+		mtk_dsi_reset_dphy(dsi);
+		mtk_dsi_clk_ulp_mode_leave(dsi);
+		mtk_dsi_lane0_ulp_mode_leave(dsi);
+		mtk_dsi_clk_hs_mode(dsi, 0);
+		msleep(20);
+		/* The reaction time after pulling up the mipi signal for dsi_rx */
+	}
 }
 
 static void mtk_output_dsi_enable(struct mtk_dsi *dsi)
@@ -708,6 +720,7 @@ static void mtk_output_dsi_enable(struct mtk_dsi *dsi)
 	if (dsi->enabled)
 		return;
 
+	mtk_dsi_lane_ready(dsi);
 	mtk_dsi_set_mode(dsi);
 	mtk_dsi_clk_hs_mode(dsi, 1);
 
@@ -1017,6 +1030,8 @@ static ssize_t mtk_dsi_host_transfer(struct mipi_dsi_host *host,
 	if (MTK_DSI_HOST_IS_READ(msg->type))
 		irq_flag |= LPRX_RD_RDY_INT_FLAG;
 
+	mtk_dsi_lane_ready(dsi);
+
 	ret = mtk_dsi_host_send_cmd(dsi, msg, irq_flag);
 	if (ret)
 		goto restore_dsi_mode;
-- 
2.18.0




More information about the Linux-mediatek mailing list