[PATCH v3, 03/10] dt-bindings: media: mtk-vcodec: Adds encoder cores dt-bindings for mt8195
Irui Wang
irui.wang at mediatek.com
Wed Mar 30 01:48:47 PDT 2022
Dear Rob,
A sample encoder hardware block diagram attached.
On Tue, 2022-03-29 at 08:09 -0500, Rob Herring wrote:
> On Tue, Mar 29, 2022 at 09:26:37AM +0800, Irui Wang wrote:
> > Dear Rob,
> >
> > Many thanks for your attention.
> >
> > On Mon, 2022-03-28 at 08:48 -0500, Rob Herring wrote:
> > > On Sat, Mar 26, 2022 at 10:00:55AM +0800, Irui Wang wrote:
> > > > Dear Rob,
> > > >
> > > > Thanks for your review and comments.
> > > >
> > > > On Fri, 2022-03-25 at 15:57 -0500, Rob Herring wrote:
> > > > > On Thu, Mar 17, 2022 at 04:22:23PM +0800, Irui Wang wrote:
> > > > > > Adds encoder cores dt-bindings for mt8195.
>
> [...]
>
> > > > > > + mediatek,core-id:
> > > > > > + $ref: /schemas/types.yaml#/definitions/uint32
> > > > > > + description: |
> > > > > > + Current encoder core id.
> > > > >
> > > > > What is this for and what does its value correspond to in the
> > > > > h/w.
> > > > > We
> > > > > generally don't do made up indices in DT.
> > > >
> > > > It's for encoder core id, core at 1a020000 must be core-0,
> > > > core at 1b020000
> > > > must be core-1, we add this property in each child node, so we
> > > > can
> > > > get core-id in drivers. If it can't ref "uint32" types yaml,
> > > > would
> > > > you mind giving some more suggestions ?
> > >
> > > I still don't understand why it is needed. What is 'core-0'?
> > >
> > > Is there some functional difference between the cores? If so,
> > > describe
> > > that difference.
> > >
> > > Rob
> >
> > They are two different pieces of hardware, it's our encoder
> > hardware
> > design. There are two encoder hardware cores inside MT8195, named
> > core0
> > and core1(we can rename it, but core id should be declared),
> > for core0, its module base address is 0x1A02_0000, uses IOMMU
> > "vdo0_iommu" and power domain "POWER_DOMAIN_VENC",
> > for core1, its module base address is 0x1B02_0000, uses IOMMU
> > "vpp_iommu" and power domain "POWER_DOMAIN_VENC_CORE1".
> > So the two encoder cores have their own base, IRQ, clock, power,
> > etc.
> > Each core can encode independently, moreover, they can work
> > together
> > for higher performance.
> > We will describe more details in YAML about it if it's OK for you.
>
> All the resources you list are in the child nodes, so you don't need
> 0
> and 1 numbering for those.
>
> Looking at the driver patches, the only thing I see distinguishing
> core numbers is this:
>
> "frame#0 uses core#0, frame#1 uses core#1, frame#2 uses core#0...,
>
> Lock the device and enable the clock by used core, for sequence
> header encoding, it always uses core#0."
>
> Is this a requirement in the h/w or just what the driver picked?
> IOW,
> could frame#0 use core#1?
No, it's a requirement in the h/w, driver trigger core start encoding
is in order.
About the encoder hardware block diagram, please check below:
--------------------------------------------------------------
Input Buffer: 0 1 2 3 4 5 6
| | | | | | |
v | v | v | v
+-------+ | +-------+ | +-------+ | +-------+
| core0 | | | core0 | | | core0 | | | core0 |
+-------+ | +-------+ | +-------+ | +-------+
| | | | | | |
| v | v | v |
| +-------+ | +-------+ | +-------+ |
| | core1 | | | core1 | | | core1 | |
| +-------+ | +-------+ | +-------+ |
| | | | | | |
v v v v v v v <parent>
--------------------------------------------------------------
core || index <child>
\/
+-----------------------------------------------+
| core0/core1 |
| enable/disable power/clk/irq |
+-----------------------------------------------+
--------------------------------------------------------------
As above , there are parent and child devices, child mean each venc
core, the child device controls the information of each core
independent which inlcude power/clk/irq.
When start encoding, input buffer 0 will be encoded by core0, and input
buffer 1 can be encoded by core1 even if buffer 0 has not been encoded
done yet, after buffer 0 encoded done, buffer 2 will be encoded by
core0, and buffer 1 encoded done by core1. These two encoder cores will
encode each input in this overlapping manner.
We need manage each child device in parent device by core-id property.
And we also need record current encoding input buffer, encode done
output buffers and which one core is in used through core-id, because
the two cores are encoding at the same time under one parent driver.
>
> Rob
Thanks
Best Regards
More information about the Linux-mediatek
mailing list