[PATCH v3 10/14] iio: adc: mt6370: Add Mediatek MT6370 support

Andy Shevchenko andy.shevchenko at gmail.com
Thu Jun 23 11:25:48 PDT 2022


On Thu, Jun 23, 2022 at 2:00 PM ChiaEn Wu <peterwu.pub at gmail.com> wrote:
>
> From: ChiaEn Wu <chiaen_wu at richtek.com>
>
> Add Mediatek MT6370 ADC support.

...

> +config MEDIATEK_MT6370_ADC
> +       tristate "Mediatek MT6370 ADC driver"
> +       depends on MFD_MT6370
> +       help
> +         Say yes here to enable Mediatek MT6370 ADC support.
> +
> +         This ADC driver provides 9 channels for system monitoring (charger
> +         current, voltage, and temperature).

What will be the module name?

...

> +#include <dt-bindings/iio/adc/mediatek,mt6370_adc.h>

Usually this goes after linux/* asm/* as it's not so generic.

> +#include <linux/bits.h>
> +#include <linux/bitfield.h>
> +#include <linux/iio/iio.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>

> +#include <linux/mod_devicetable.h>

I believe the order should be otherwise, this is first followed by module.h.

> +#include <linux/mutex.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>

...

> +#define ADC_CONV_POLLING_TIME          1000

If it's time, add a unit suffix, if it's a counter, make it clear.

...

> +       msleep(ADC_CONV_TIME_US / 1000);

Why define microseconds if milliseconds are in use?

...

> +       ret = regmap_read_poll_timeout(priv->regmap,
> +                                      MT6370_REG_CHG_ADC, reg_val,
> +                                      !(reg_val & MT6370_ADC_START_MASK),
> +                                      ADC_CONV_POLLING_TIME,
> +                                      ADC_CONV_TIME_US * 3);
> +       if (ret) {
> +               if (ret == -ETIMEDOUT)
> +                       dev_err(priv->dev, "Failed to wait ADC conversion\n");

wait for

> +               else
> +                       dev_err(priv->dev,
> +                               "Failed to read ADC register (%d)\n", ret);

Do you really need to differentiate the errors here? I believe the
latter one covers all cases.

> +               goto adc_unlock;
> +       }

...

> +#define MT6370_ADC_CHAN(_idx, _type, _addr, _extra_info) {     \
> +       .type = _type,                                          \
> +       .channel = MT6370_CHAN_##_idx,                          \
> +       .address = _addr,                                       \
> +       .scan_index = MT6370_CHAN_##_idx,                       \
> +       .indexed = 1,                                           \
> +       .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |          \
> +                             BIT(IIO_CHAN_INFO_SCALE) |        \
> +                             _extra_info                       \

Leave a comma after the last member as well.

> +}

...

> +       regmap = dev_get_regmap(pdev->dev.parent, NULL);
> +       if (!regmap) {

> +               dev_err(&pdev->dev, "Failed to get regmap\n");
> +               return -ENODEV;

return dev_err_probe(...);

> +       }

...

> +       ret = regmap_write(priv->regmap, MT6370_REG_CHG_ADC, 0);
> +       if (ret) {
> +               dev_err(&pdev->dev, "Failed to reset ADC\n");
> +               return ret;
> +       }

Ditto.

-- 
With Best Regards,
Andy Shevchenko



More information about the Linux-mediatek mailing list