[PATCH v11 3/3] arm64: dts: Add MediaTek SoC MT8186 dts and evaluation board and Makefile
AngeloGioacchino Del Regno
angelogioacchino.delregno at collabora.com
Thu Jul 7 02:31:32 PDT 2022
Il 20/05/22 14:22, Allen-KH Cheng ha scritto:
> Add basic chip support for MediaTek MT8186.
>
> Signed-off-by: Allen-KH Cheng <Allen-KH.Cheng at mediatek.com>
> ---
> arch/arm64/boot/dts/mediatek/Makefile | 1 +
> arch/arm64/boot/dts/mediatek/mt8186-evb.dts | 232 +++++
> arch/arm64/boot/dts/mediatek/mt8186.dtsi | 1016 +++++++++++++++++++
> 3 files changed, 1249 insertions(+)
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-evb.dts
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8186.dtsi
>
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index c7d4636a2cb7..50a2c58c5f56 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -37,6 +37,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kodama-sku32.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku0.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-pumpkin.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-evb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-evb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt8186-evb.dts b/arch/arm64/boot/dts/mediatek/mt8186-evb.dts
> new file mode 100644
> index 000000000000..3e8018c1e802
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8186-evb.dts
> @@ -0,0 +1,232 @@
> +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +/*
> + * Copyright (C) 2022 MediaTek Inc.
> + */
> +/dts-v1/;
> +#include "mt8186.dtsi"
> +
> +/ {
> + model = "MediaTek MT8186 evaluation board";
> + compatible = "mediatek,mt8186-evb", "mediatek,mt8186";
> +
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:921600n8";
> + };
> +
> + memory {
> + device_type = "memory";
> + reg = <0 0x40000000 0 0x80000000>;
> + };
> +};
> +
> +&i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0_pins>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
> +};
> +
> +&i2c1 {
> + clock-frequency = <400000>;
> + i2c-scl-internal-delay-ns = <8000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1_pins>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + status = "okay";
> +};
> +
Can you please reorder like:
&i2c1 {
status = "okay";
clock-frequency = <400000>;
i2c-scl-internal-delay-ns = <12500>;
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
};
Also, address and size cells are common properties and will not change
on a per-board basis: please define them in mt8186.dtsi instead.
Same for the other nodes.
> +&i2c2 {
..snip..
> +
> +&pio {
> + i2c0_pins: i2c0{
Please perform a dtbs_check before pushing devicetrees upstream:
this node will give you a warning, bindings related warnings are
considered like code warnings and they shall not happen.
pinctrl-mt8186.yaml defines patternProperties as '-pins$'
so this should be:
i2c0_pins: i2c0-pins {
Please fix.
> + pins-sda-scl {
> + pinmux = <PINMUX_GPIO128__FUNC_SDA0>,
> + <PINMUX_GPIO127__FUNC_SCL0>;
> + bias-disable;
> + mediatek,drive-strength-adv = <0>;
Do not use mediatek,drive-strength-adv: it's not right in principle
to have this property, as it can be expressed with the standard
drive-strength-microamp property instead.
Check pinctrl-mt8192.yaml (or my commits to pinctrl-mt8195.yaml) for
more information.
> + drive-strength = <MTK_DRIVE_4mA>;
MTK_DRIVE_(x)mA maps to the actual value in mA: please stop using this
definition and simply define this as
drive-strength = <4>;
> + input-enable;
> + };
> + };
> +
..snip..
> +
> +&u3phy0 {
> + status="okay";
This should be
status = "okay";
> +};
> +
> +&u3phy1 {
> + status="okay";
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +&xhci0 {
> + status = "okay";
> +};
> +
> +&xhci1 {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/mediatek/mt8186.dtsi b/arch/arm64/boot/dts/mediatek/mt8186.dtsi
> new file mode 100644
> index 000000000000..35281db2e2b9
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8186.dtsi
> @@ -0,0 +1,1016 @@
> +// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +/*
> + * Copyright (C) 2022 MediaTek Inc.
> + * Author: Allen-KH Cheng <allen-kh.cheng at mediatek.com>
> + */
> +/dts-v1/;
> +#include <dt-bindings/clock/mt8186-clk.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/pinctrl/mt8186-pinfunc.h>
> +#include <dt-bindings/power/mt8186-power.h>
> +#include <dt-bindings/phy/phy.h>
> +#include <dt-bindings/reset/mt8186-resets.h>
> +
> +/ {
> + compatible = "mediatek,mt8186";
> + interrupt-parent = <&gic>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
..snip..
> +
> + cpu0: cpu at 0 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a55";
> + reg = <0x000>;
> + enable-method = "psci";
> + clock-frequency = <2000000000>;
> + capacity-dmips-mhz = <382>;
> + cpu-idle-states = <&cpu_off_l &cluster_off_l>;
> + next-level-cache = <&l2_0>;
No cooling cells?
> + };
> +
..snip..
> +
> + soc {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + compatible = "simple-bus";
> + ranges;
> +
> + gic: interrupt-controller at c000000 {
> + compatible = "arm,gic-v3";
> + #interrupt-cells = <3>;
You're describing PPI partitions below... even if you're not currently
planning to define PPI affinity just yet, interrupt cells should be 4
so that defining affinity will be pretty straightforward in the future.
Please change interrupt-cells to 4.
> + #address-cells = <2>;
> + #size-cells = <2>;
> + #redistributor-regions = <1>;
> + interrupt-parent = <&gic>;
> + interrupt-controller;
> + reg = <0 0x0c000000 0 0x40000>,
> + <0 0x0c040000 0 0x200000>;
> + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
> +
> + ppi-partitions {
> + ppi_cluster0: interrupt-partition-0 {
> + affinity = <&cpu0 &cpu1 &cpu2 &cpu3 &cpu4 &cpu5>;
> + };
> +
> + ppi_cluster1: interrupt-partition-1 {
> + affinity = <&cpu6 &cpu7>;
> + };
> + };
> + };
> +
> + mcusys: syscon at c53a000 {
> + compatible = "mediatek,mt8186-mcusys", "syscon";
> + reg = <0 0xc53a000 0 0x1000>;
> + #clock-cells = <1>;
> + };
> +
> + topckgen: syscon at 10000000 {
> + compatible = "mediatek,mt8186-topckgen", "syscon";
> + reg = <0 0x10000000 0 0x1000>;
> + #clock-cells = <1>;
> + };
> +
> + infracfg_ao: syscon at 10001000 {
> + compatible = "mediatek,mt8186-infracfg_ao", "syscon";
> + reg = <0 0x10001000 0 0x1000>;
> + #clock-cells = <1>;
You missed reset-cells here. This driver is also defining a reset controller.
> + };
> +
> + pericfg: syscon at 10003000 {
> + compatible = "mediatek,mt8186-pericfg", "syscon";
> + reg = <0 0x10003000 0 0x1000>;
> + };
> +
> + pio: pinctrl at 10005000 {
> + compatible = "mediatek,mt8186-pinctrl";
> + reg = <0 0x10005000 0 0x1000>,
> + <0 0x10002000 0 0x0200>,
> + <0 0x10002200 0 0x0200>,
> + <0 0x10002400 0 0x0200>,
> + <0 0x10002600 0 0x0200>,
> + <0 0x10002A00 0 0x0200>,
> + <0 0x10002C00 0 0x0200>,
> + <0 0x1000B000 0 0x1000>;
> + reg-names = "iocfg0", "iocfg_lt", "iocfg_lm", "iocfg_lb",
> + "iocfg_bl", "iocfg_rb", "iocfg_rt", "eint";
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-ranges = <&pio 0 0 185>;
> + interrupt-controller;
> + interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
> + #interrupt-cells = <2>;
> + };
> +
> + scpsys: syscon at 10006000 {
> + compatible = "syscon", "simple-mfd";
> + reg = <0 0x10006000 0 0x1000>;
> + #power-domain-cells = <1>;
> +
> + /* System Power Manager */
> + spm: power-controller {
> + compatible = "mediatek,mt8186-power-controller";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + #power-domain-cells = <1>;
> +
> + /* power domain of the SoC */
> + mfg0: power-domain at MT8186_POWER_DOMAIN_MFG0 {
> + reg = <MT8186_POWER_DOMAIN_MFG0>;
> + clocks = <&topckgen CLK_TOP_MFG>;
> + clock-names= "mfg00";
Missing space: `clock-names = "mfg00";`
> + #address-cells = <1>;
> + #size-cells = <0>;
> + #power-domain-cells = <1>;
> +
> + power-domain at MT8186_POWER_DOMAIN_MFG1 {
> + reg = <MT8186_POWER_DOMAIN_MFG1>;
> + mediatek,infracfg = <&infracfg_ao>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + #power-domain-cells = <1>;
> +
> + power-domain at MT8186_POWER_DOMAIN_MFG2 {
> + reg = <MT8186_POWER_DOMAIN_MFG2>;
> + #power-domain-cells = <0>;
> + };
> +
> + power-domain at MT8186_POWER_DOMAIN_MFG3 {
> + reg = <MT8186_POWER_DOMAIN_MFG3>;
> + #power-domain-cells = <0>;
> + };
> + };
> + };
> +
> + power-domain at MT8186_POWER_DOMAIN_CSIRX_TOP {
> + reg = <MT8186_POWER_DOMAIN_CSIRX_TOP>;
> + clocks = <&topckgen CLK_TOP_SENINF>,
> + <&topckgen CLK_TOP_SENINF1>;
> + clock-names= "csirx_top0", "csirx_top1";
Same here.
> + #power-domain-cells = <0>;
> + };
> +
> + power-domain at MT8186_POWER_DOMAIN_SSUSB {
> + reg = <MT8186_POWER_DOMAIN_SSUSB>;
> + #power-domain-cells = <0>;
> + };
> +
> + power-domain at MT8186_POWER_DOMAIN_SSUSB_P1 {
> + reg = <MT8186_POWER_DOMAIN_SSUSB_P1>;
> + #power-domain-cells = <0>;
> + };
> +
> + power-domain at MT8186_POWER_DOMAIN_ADSP_AO {
> + reg = <MT8186_POWER_DOMAIN_ADSP_AO>;
> + clocks = <&topckgen CLK_TOP_AUDIODSP>,
> + <&topckgen CLK_TOP_ADSP_BUS>;
> + clock-names= "adsp_ao0", "adsp_ao1";
...and here, and everywhere else, please fix.
> + #address-cells = <1>;
> + #size-cells = <0>;
> + #power-domain-cells = <1>;
> +
Regards,
Angelo
More information about the Linux-mediatek
mailing list