[PATCH v22 3/7] soc: mediatek: SVS: introduce MTK SVS engine
Roger Lu
roger.lu at mediatek.com
Wed Jan 26 19:39:52 PST 2022
The Smart Voltage Scaling(SVS) engine is a piece of hardware
which calculates suitable SVS bank voltages to OPP voltage table.
Then, DVFS driver could apply those SVS bank voltages to PMIC/Buck
when receiving OPP_EVENT_ADJUST_VOLTAGE.
Signed-off-by: Roger Lu <roger.lu at mediatek.com>
---
drivers/soc/mediatek/Kconfig | 10 +
drivers/soc/mediatek/Makefile | 1 +
drivers/soc/mediatek/mtk-svs.c | 1422 ++++++++++++++++++++++++++++++++
3 files changed, 1433 insertions(+)
create mode 100644 drivers/soc/mediatek/mtk-svs.c
diff --git a/drivers/soc/mediatek/Kconfig b/drivers/soc/mediatek/Kconfig
index fdd8bc08569e..3c3eedea35f7 100644
--- a/drivers/soc/mediatek/Kconfig
+++ b/drivers/soc/mediatek/Kconfig
@@ -73,4 +73,14 @@ config MTK_MMSYS
Say yes here to add support for the MediaTek Multimedia
Subsystem (MMSYS).
+config MTK_SVS
+ tristate "MediaTek Smart Voltage Scaling(SVS)"
+ depends on MTK_EFUSE && NVMEM
+ help
+ The Smart Voltage Scaling(SVS) engine is a piece of hardware
+ which has several controllers(banks) for calculating suitable
+ voltage to different power domains(CPU/GPU/CCI) according to
+ chip process corner, temperatures and other factors. Then DVFS
+ driver could apply SVS bank voltage to PMIC/Buck.
+
endmenu
diff --git a/drivers/soc/mediatek/Makefile b/drivers/soc/mediatek/Makefile
index 90270f8114ed..0e9e703c931a 100644
--- a/drivers/soc/mediatek/Makefile
+++ b/drivers/soc/mediatek/Makefile
@@ -7,3 +7,4 @@ obj-$(CONFIG_MTK_SCPSYS) += mtk-scpsys.o
obj-$(CONFIG_MTK_SCPSYS_PM_DOMAINS) += mtk-pm-domains.o
obj-$(CONFIG_MTK_MMSYS) += mtk-mmsys.o
obj-$(CONFIG_MTK_MMSYS) += mtk-mutex.o
+obj-$(CONFIG_MTK_SVS) += mtk-svs.o
diff --git a/drivers/soc/mediatek/mtk-svs.c b/drivers/soc/mediatek/mtk-svs.c
new file mode 100644
index 000000000000..2d7ea3d607c4
--- /dev/null
+++ b/drivers/soc/mediatek/mtk-svs.c
@@ -0,0 +1,1422 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2022 MediaTek Inc.
+ */
+
+#include <linux/bits.h>
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/device.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/kthread.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/pm_domain.h>
+#include <linux/pm_opp.h>
+#include <linux/pm_qos.h>
+#include <linux/pm_runtime.h>
+#include <linux/regulator/consumer.h>
+#include <linux/slab.h>
+#include <linux/spinlock.h>
+
+/* svs bank 1-line software id */
+#define SVSB_CPU_LITTLE BIT(0)
+#define SVSB_CPU_BIG BIT(1)
+#define SVSB_CCI BIT(2)
+#define SVSB_GPU BIT(3)
+
+/* svs bank mode support */
+#define SVSB_MODE_ALL_DISABLE 0
+#define SVSB_MODE_INIT01 BIT(1)
+#define SVSB_MODE_INIT02 BIT(2)
+
+/* svs bank volt flags */
+#define SVSB_INIT01_PD_REQ BIT(0)
+#define SVSB_INIT01_VOLT_IGNORE BIT(1)
+#define SVSB_INIT01_VOLT_INC_ONLY BIT(2)
+
+/* svs bank register common configuration */
+#define SVSB_DET_MAX 0xffff
+#define SVSB_DET_WINDOW 0xa28
+#define SVSB_DTHI 0x1
+#define SVSB_DTLO 0xfe
+#define SVSB_EN_INIT01 0x1
+#define SVSB_EN_INIT02 0x5
+#define SVSB_EN_OFF 0x0
+#define SVSB_INTEN_INIT0x 0x00005f01
+#define SVSB_INTSTS_CLEAN 0x00ffffff
+#define SVSB_INTSTS_COMPLETE 0x1
+#define SVSB_RUNCONFIG_DEFAULT 0x80000000
+
+/* svs bank related setting */
+#define MAX_OPP_ENTRIES 16
+#define SVSB_DC_SIGNED_BIT BIT(15)
+#define SVSB_DET_CLK_EN BIT(31)
+
+static DEFINE_SPINLOCK(svs_lock);
+
+/**
+ * enum svsb_phase - svs bank phase enumeration
+ * @SVSB_PHASE_ERROR: svs bank encounters unexpected condition
+ * @SVSB_PHASE_INIT01: svs bank basic init for data calibration
+ * @SVSB_PHASE_INIT02: svs bank can provide voltages to opp table
+ * @SVSB_PHASE_MAX: total number of svs bank phase (debug purpose)
+ *
+ * Each svs bank has its own independent phase and we enable each svs bank by
+ * running their phase orderly. However, when svs bank encounters unexpected
+ * condition, it will fire an irq (PHASE_ERROR) to inform svs software.
+ *
+ * svs bank general phase-enabled order:
+ * SVSB_PHASE_INIT01 -> SVSB_PHASE_INIT02
+ */
+enum svsb_phase {
+ SVSB_PHASE_ERROR = 0,
+ SVSB_PHASE_INIT01,
+ SVSB_PHASE_INIT02,
+ SVSB_PHASE_MAX,
+};
+
+enum svs_reg_index {
+ DESCHAR = 0,
+ TEMPCHAR,
+ DETCHAR,
+ AGECHAR,
+ DCCONFIG,
+ AGECONFIG,
+ FREQPCT30,
+ FREQPCT74,
+ LIMITVALS,
+ VBOOT,
+ DETWINDOW,
+ CONFIG,
+ TSCALCS,
+ RUNCONFIG,
+ SVSEN,
+ INIT2VALS,
+ DCVALUES,
+ AGEVALUES,
+ VOP30,
+ VOP74,
+ TEMP,
+ INTSTS,
+ INTSTSRAW,
+ INTEN,
+ CHKINT,
+ CHKSHIFT,
+ STATUS,
+ VDESIGN30,
+ VDESIGN74,
+ DVT30,
+ DVT74,
+ AGECOUNT,
+ SMSTATE0,
+ SMSTATE1,
+ CTL0,
+ DESDETSEC,
+ TEMPAGESEC,
+ CTRLSPARE0,
+ CTRLSPARE1,
+ CTRLSPARE2,
+ CTRLSPARE3,
+ CORESEL,
+ THERMINTST,
+ INTST,
+ THSTAGE0ST,
+ THSTAGE1ST,
+ THSTAGE2ST,
+ THAHBST0,
+ THAHBST1,
+ SPARE0,
+ SPARE1,
+ SPARE2,
+ SPARE3,
+ THSLPEVEB,
+ SVS_REG_MAX,
+};
+
+static const u32 svs_regs_v2[] = {
+ [DESCHAR] = 0xc00,
+ [TEMPCHAR] = 0xc04,
+ [DETCHAR] = 0xc08,
+ [AGECHAR] = 0xc0c,
+ [DCCONFIG] = 0xc10,
+ [AGECONFIG] = 0xc14,
+ [FREQPCT30] = 0xc18,
+ [FREQPCT74] = 0xc1c,
+ [LIMITVALS] = 0xc20,
+ [VBOOT] = 0xc24,
+ [DETWINDOW] = 0xc28,
+ [CONFIG] = 0xc2c,
+ [TSCALCS] = 0xc30,
+ [RUNCONFIG] = 0xc34,
+ [SVSEN] = 0xc38,
+ [INIT2VALS] = 0xc3c,
+ [DCVALUES] = 0xc40,
+ [AGEVALUES] = 0xc44,
+ [VOP30] = 0xc48,
+ [VOP74] = 0xc4c,
+ [TEMP] = 0xc50,
+ [INTSTS] = 0xc54,
+ [INTSTSRAW] = 0xc58,
+ [INTEN] = 0xc5c,
+ [CHKINT] = 0xc60,
+ [CHKSHIFT] = 0xc64,
+ [STATUS] = 0xc68,
+ [VDESIGN30] = 0xc6c,
+ [VDESIGN74] = 0xc70,
+ [DVT30] = 0xc74,
+ [DVT74] = 0xc78,
+ [AGECOUNT] = 0xc7c,
+ [SMSTATE0] = 0xc80,
+ [SMSTATE1] = 0xc84,
+ [CTL0] = 0xc88,
+ [DESDETSEC] = 0xce0,
+ [TEMPAGESEC] = 0xce4,
+ [CTRLSPARE0] = 0xcf0,
+ [CTRLSPARE1] = 0xcf4,
+ [CTRLSPARE2] = 0xcf8,
+ [CTRLSPARE3] = 0xcfc,
+ [CORESEL] = 0xf00,
+ [THERMINTST] = 0xf04,
+ [INTST] = 0xf08,
+ [THSTAGE0ST] = 0xf0c,
+ [THSTAGE1ST] = 0xf10,
+ [THSTAGE2ST] = 0xf14,
+ [THAHBST0] = 0xf18,
+ [THAHBST1] = 0xf1c,
+ [SPARE0] = 0xf20,
+ [SPARE1] = 0xf24,
+ [SPARE2] = 0xf28,
+ [SPARE3] = 0xf2c,
+ [THSLPEVEB] = 0xf30,
+};
+
+/**
+ * struct svs_platform - svs platform control
+ * @name: svs platform name
+ * @base: svs platform register base
+ * @dev: svs platform device
+ * @main_clk: main clock for svs bank
+ * @pbank: svs bank pointer needing to be protected by spin_lock section
+ * @banks: svs banks that svs platform supports
+ * @efuse_parsing: svs platform efuse parsing function pointer
+ * @probe: svs platform probe function pointer
+ * @irqflags: svs platform irq settings flags
+ * @efuse_max: total number of svs efuse
+ * @regs: svs platform registers map
+ * @bank_max: total number of svs banks
+ * @efuse: svs efuse data received from NVMEM framework
+ */
+struct svs_platform {
+ char *name;
+ void __iomem *base;
+ struct device *dev;
+ struct clk *main_clk;
+ struct svs_bank *pbank;
+ struct svs_bank *banks;
+ bool (*efuse_parsing)(struct svs_platform *svsp);
+ int (*probe)(struct svs_platform *svsp);
+ unsigned long irqflags;
+ size_t efuse_max;
+ const u32 *regs;
+ u32 bank_max;
+ u32 *efuse;
+};
+
+struct svs_platform_data {
+ char *name;
+ struct svs_bank *banks;
+ bool (*efuse_parsing)(struct svs_platform *svsp);
+ int (*probe)(struct svs_platform *svsp);
+ unsigned long irqflags;
+ const u32 *regs;
+ u32 bank_max;
+};
+
+/**
+ * struct svs_bank - svs bank representation
+ * @dev: bank device
+ * @opp_dev: device for opp table/buck control
+ * @pd_dev: power domain device for SoC mtcmos control
+ * @init_completion: the timeout completion for bank init
+ * @buck: regulator used by opp_dev
+ * @lock: mutex lock to protect voltage update process
+ * @set_freq_pct: function pointer to set bank frequency percent table
+ * @get_volts: function pointer to get bank voltages
+ * @name: bank name
+ * @buck_name: regulator name
+ * @phase: bank current phase
+ * @volt_od: bank voltage overdrive
+ * @pm_runtime_enabled_count: bank pm runtime enabled count
+ * @mode_support: bank mode support.
+ * @freq_base: reference frequency for bank init
+ * @vboot: voltage request for bank init01 only
+ * @opp_dfreq: default opp frequency table
+ * @opp_dvolt: default opp voltage table
+ * @freq_pct: frequency percent table for bank init
+ * @volt: bank voltage table
+ * @volt_step: bank voltage step
+ * @volt_base: bank voltage base
+ * @volt_flags: bank voltage flags
+ * @vmax: bank voltage maximum
+ * @vmin: bank voltage minimum
+ * @age_config: bank age configuration
+ * @age_voffset_in: bank age voltage offset
+ * @dc_config: bank dc configuration
+ * @dc_voffset_in: bank dc voltage offset
+ * @dvt_fixed: bank dvt fixed value
+ * @vco: bank VCO value
+ * @chk_shift: bank chicken shift
+ * @core_sel: bank selection
+ * @opp_count: bank opp count
+ * @int_st: bank interrupt identification
+ * @sw_id: bank software identification
+ * @cpu_id: cpu core id for SVS CPU bank use only
+ * @ctl0: TS-x selection
+ * @bdes: svs efuse data
+ * @mdes: svs efuse data
+ * @mtdes: svs efuse data
+ * @dcbdet: svs efuse data
+ * @dcmdet: svs efuse data
+ *
+ * Svs bank will generate suitalbe voltages by below general math equation
+ * and provide these voltages to opp voltage table.
+ *
+ * opp_volt[i] = (volt[i] * volt_step) + volt_base;
+ */
+struct svs_bank {
+ struct device *dev;
+ struct device *opp_dev;
+ struct device *pd_dev;
+ struct completion init_completion;
+ struct regulator *buck;
+ struct mutex lock; /* lock to protect voltage update process */
+ void (*set_freq_pct)(struct svs_platform *svsp);
+ void (*get_volts)(struct svs_platform *svsp);
+ char *name;
+ char *buck_name;
+ enum svsb_phase phase;
+ s32 volt_od;
+ u32 pm_runtime_enabled_count;
+ u32 mode_support;
+ u32 freq_base;
+ u32 vboot;
+ u32 opp_dfreq[MAX_OPP_ENTRIES];
+ u32 opp_dvolt[MAX_OPP_ENTRIES];
+ u32 freq_pct[MAX_OPP_ENTRIES];
+ u32 volt[MAX_OPP_ENTRIES];
+ u32 volt_step;
+ u32 volt_base;
+ u32 volt_flags;
+ u32 vmax;
+ u32 vmin;
+ u32 age_config;
+ u32 age_voffset_in;
+ u32 dc_config;
+ u32 dc_voffset_in;
+ u32 dvt_fixed;
+ u32 vco;
+ u32 chk_shift;
+ u32 core_sel;
+ u32 opp_count;
+ u32 int_st;
+ u32 sw_id;
+ u32 cpu_id;
+ u32 ctl0;
+ u32 bdes;
+ u32 mdes;
+ u32 mtdes;
+ u32 dcbdet;
+ u32 dcmdet;
+};
+
+static u32 percent(u32 numerator, u32 denominator)
+{
+ /* If not divide 1000, "numerator * 100" will have data overflow. */
+ numerator /= 1000;
+ denominator /= 1000;
+
+ return DIV_ROUND_UP(numerator * 100, denominator);
+}
+
+static u32 svs_readl_relaxed(struct svs_platform *svsp, enum svs_reg_index rg_i)
+{
+ return readl_relaxed(svsp->base + svsp->regs[rg_i]);
+}
+
+static void svs_writel_relaxed(struct svs_platform *svsp, u32 val,
+ enum svs_reg_index rg_i)
+{
+ writel_relaxed(val, svsp->base + svsp->regs[rg_i]);
+}
+
+static void svs_switch_bank(struct svs_platform *svsp)
+{
+ struct svs_bank *svsb = svsp->pbank;
+
+ svs_writel_relaxed(svsp, svsb->core_sel, CORESEL);
+}
+
+static u32 svs_bank_volt_to_opp_volt(u32 svsb_volt, u32 svsb_volt_step,
+ u32 svsb_volt_base)
+{
+ return (svsb_volt * svsb_volt_step) + svsb_volt_base;
+}
+
+static int svs_adjust_pm_opp_volts(struct svs_bank *svsb)
+{
+ int ret = -EPERM;
+ u32 i, svsb_volt, opp_volt;
+
+ mutex_lock(&svsb->lock);
+
+ /* vmin <= svsb_volt (opp_volt) <= default opp voltage */
+ for (i = 0; i < svsb->opp_count; i++) {
+ switch (svsb->phase) {
+ case SVSB_PHASE_ERROR:
+ opp_volt = svsb->opp_dvolt[i];
+ break;
+ case SVSB_PHASE_INIT01:
+ /* do nothing */
+ goto unlock_mutex;
+ case SVSB_PHASE_INIT02:
+ svsb_volt = max(svsb->volt[i], svsb->vmin);
+ opp_volt = svs_bank_volt_to_opp_volt(svsb_volt,
+ svsb->volt_step,
+ svsb->volt_base);
+ break;
+ default:
+ dev_err(svsb->dev, "unknown phase: %u\n", svsb->phase);
+ ret = -EINVAL;
+ goto unlock_mutex;
+ }
+
+ opp_volt = min(opp_volt, svsb->opp_dvolt[i]);
+ ret = dev_pm_opp_adjust_voltage(svsb->opp_dev,
+ svsb->opp_dfreq[i],
+ opp_volt, opp_volt,
+ svsb->opp_dvolt[i]);
+ if (ret) {
+ dev_err(svsb->dev, "set %uuV fail: %d\n",
+ opp_volt, ret);
+ goto unlock_mutex;
+ }
+ }
+
+unlock_mutex:
+ mutex_unlock(&svsb->lock);
+
+ return ret;
+}
+
+static u32 interpolate(u32 f0, u32 f1, u32 v0, u32 v1, u32 fx)
+{
+ u32 vx;
+
+ if (v0 == v1 || f0 == f1)
+ return v0;
+
+ /* *100 to have decimal fraction factor */
+ vx = (v0 * 100) - ((((v0 - v1) * 100) / (f0 - f1)) * (f0 - fx));
+
+ return DIV_ROUND_UP(vx, 100);
+}
+
+static void svs_get_bank_volts_v2(struct svs_platform *svsp)
+{
+ struct svs_bank *svsb = svsp->pbank;
+ u32 temp, i;
+
+ temp = svs_readl_relaxed(svsp, VOP74);
+ svsb->volt[14] = (temp >> 24) & GENMASK(7, 0);
+ svsb->volt[12] = (temp >> 16) & GENMASK(7, 0);
+ svsb->volt[10] = (temp >> 8) & GENMASK(7, 0);
+ svsb->volt[8] = (temp & GENMASK(7, 0));
+
+ temp = svs_readl_relaxed(svsp, VOP30);
+ svsb->volt[6] = (temp >> 24) & GENMASK(7, 0);
+ svsb->volt[4] = (temp >> 16) & GENMASK(7, 0);
+ svsb->volt[2] = (temp >> 8) & GENMASK(7, 0);
+ svsb->volt[0] = (temp & GENMASK(7, 0));
+
+ for (i = 0; i <= 12; i += 2)
+ svsb->volt[i + 1] = interpolate(svsb->freq_pct[i],
+ svsb->freq_pct[i + 2],
+ svsb->volt[i],
+ svsb->volt[i + 2],
+ svsb->freq_pct[i + 1]);
+
+ svsb->volt[15] = interpolate(svsb->freq_pct[12],
+ svsb->freq_pct[14],
+ svsb->volt[12],
+ svsb->volt[14],
+ svsb->freq_pct[15]);
+
+ for (i = 0; i < svsb->opp_count; i++)
+ svsb->volt[i] += svsb->volt_od;
+}
+
+static void svs_set_bank_freq_pct_v2(struct svs_platform *svsp)
+{
+ struct svs_bank *svsb = svsp->pbank;
+
+ svs_writel_relaxed(svsp,
+ (svsb->freq_pct[14] << 24) |
+ (svsb->freq_pct[12] << 16) |
+ (svsb->freq_pct[10] << 8) |
+ svsb->freq_pct[8],
+ FREQPCT74);
+
+ svs_writel_relaxed(svsp,
+ (svsb->freq_pct[6] << 24) |
+ (svsb->freq_pct[4] << 16) |
+ (svsb->freq_pct[2] << 8) |
+ svsb->freq_pct[0],
+ FREQPCT30);
+}
+
+static void svs_set_bank_phase(struct svs_platform *svsp,
+ enum svsb_phase target_phase)
+{
+ struct svs_bank *svsb = svsp->pbank;
+ u32 des_char, temp_char, det_char, limit_vals, init2vals;
+
+ svs_switch_bank(svsp);
+
+ des_char = (svsb->bdes << 8) | svsb->mdes;
+ svs_writel_relaxed(svsp, des_char, DESCHAR);
+
+ temp_char = (svsb->vco << 16) | (svsb->mtdes << 8) | svsb->dvt_fixed;
+ svs_writel_relaxed(svsp, temp_char, TEMPCHAR);
+
+ det_char = (svsb->dcbdet << 8) | svsb->dcmdet;
+ svs_writel_relaxed(svsp, det_char, DETCHAR);
+
+ svs_writel_relaxed(svsp, svsb->dc_config, DCCONFIG);
+ svs_writel_relaxed(svsp, svsb->age_config, AGECONFIG);
+ svs_writel_relaxed(svsp, SVSB_RUNCONFIG_DEFAULT, RUNCONFIG);
+
+ svsb->set_freq_pct(svsp);
+
+ limit_vals = (svsb->vmax << 24) | (svsb->vmin << 16) |
+ (SVSB_DTHI << 8) | SVSB_DTLO;
+ svs_writel_relaxed(svsp, limit_vals, LIMITVALS);
+
+ svs_writel_relaxed(svsp, SVSB_DET_WINDOW, DETWINDOW);
+ svs_writel_relaxed(svsp, SVSB_DET_MAX, CONFIG);
+ svs_writel_relaxed(svsp, svsb->chk_shift, CHKSHIFT);
+ svs_writel_relaxed(svsp, svsb->ctl0, CTL0);
+ svs_writel_relaxed(svsp, SVSB_INTSTS_CLEAN, INTSTS);
+
+ switch (target_phase) {
+ case SVSB_PHASE_INIT01:
+ svs_writel_relaxed(svsp, svsb->vboot, VBOOT);
+ svs_writel_relaxed(svsp, SVSB_INTEN_INIT0x, INTEN);
+ svs_writel_relaxed(svsp, SVSB_EN_INIT01, SVSEN);
+ break;
+ case SVSB_PHASE_INIT02:
+ svs_writel_relaxed(svsp, SVSB_INTEN_INIT0x, INTEN);
+ init2vals = (svsb->age_voffset_in << 16) | svsb->dc_voffset_in;
+ svs_writel_relaxed(svsp, init2vals, INIT2VALS);
+ svs_writel_relaxed(svsp, SVSB_EN_INIT02, SVSEN);
+ break;
+ default:
+ dev_err(svsb->dev, "requested unknown target phase: %u\n",
+ target_phase);
+ break;
+ }
+}
+
+static inline void svs_error_isr_handler(struct svs_platform *svsp)
+{
+ struct svs_bank *svsb = svsp->pbank;
+
+ dev_err(svsb->dev, "%s: CORESEL = 0x%08x\n",
+ __func__, svs_readl_relaxed(svsp, CORESEL));
+ dev_err(svsb->dev, "SVSEN = 0x%08x, INTSTS = 0x%08x\n",
+ svs_readl_relaxed(svsp, SVSEN),
+ svs_readl_relaxed(svsp, INTSTS));
+ dev_err(svsb->dev, "SMSTATE0 = 0x%08x, SMSTATE1 = 0x%08x\n",
+ svs_readl_relaxed(svsp, SMSTATE0),
+ svs_readl_relaxed(svsp, SMSTATE1));
+
+ svsb->phase = SVSB_PHASE_ERROR;
+ svs_writel_relaxed(svsp, SVSB_EN_OFF, SVSEN);
+ svs_writel_relaxed(svsp, SVSB_INTSTS_CLEAN, INTSTS);
+}
+
+static inline void svs_init01_isr_handler(struct svs_platform *svsp)
+{
+ struct svs_bank *svsb = svsp->pbank;
+
+ dev_info(svsb->dev, "%s: VDN74~30:0x%08x~0x%08x, DC:0x%08x\n",
+ __func__, svs_readl_relaxed(svsp, VDESIGN74),
+ svs_readl_relaxed(svsp, VDESIGN30),
+ svs_readl_relaxed(svsp, DCVALUES));
+
+ svsb->phase = SVSB_PHASE_INIT01;
+ svsb->dc_voffset_in = ~(svs_readl_relaxed(svsp, DCVALUES) &
+ GENMASK(15, 0)) + 1;
+ if (svsb->volt_flags & SVSB_INIT01_VOLT_IGNORE ||
+ (svsb->dc_voffset_in & SVSB_DC_SIGNED_BIT &&
+ svsb->volt_flags & SVSB_INIT01_VOLT_INC_ONLY))
+ svsb->dc_voffset_in = 0;
+
+ svsb->age_voffset_in = svs_readl_relaxed(svsp, AGEVALUES) &
+ GENMASK(15, 0);
+
+ svs_writel_relaxed(svsp, SVSB_EN_OFF, SVSEN);
+ svs_writel_relaxed(svsp, SVSB_INTSTS_COMPLETE, INTSTS);
+ svsb->core_sel &= ~SVSB_DET_CLK_EN;
+}
+
+static inline void svs_init02_isr_handler(struct svs_platform *svsp)
+{
+ struct svs_bank *svsb = svsp->pbank;
+
+ dev_info(svsb->dev, "%s: VOP74~30:0x%08x~0x%08x, DC:0x%08x\n",
+ __func__, svs_readl_relaxed(svsp, VOP74),
+ svs_readl_relaxed(svsp, VOP30),
+ svs_readl_relaxed(svsp, DCVALUES));
+
+ svsb->phase = SVSB_PHASE_INIT02;
+ svsb->get_volts(svsp);
+
+ svs_writel_relaxed(svsp, SVSB_EN_OFF, SVSEN);
+ svs_writel_relaxed(svsp, SVSB_INTSTS_COMPLETE, INTSTS);
+}
+
+static irqreturn_t svs_isr(int irq, void *data)
+{
+ struct svs_platform *svsp = data;
+ struct svs_bank *svsb = NULL;
+ unsigned long flags;
+ u32 idx, int_sts, svs_en;
+
+ for (idx = 0; idx < svsp->bank_max; idx++) {
+ svsb = &svsp->banks[idx];
+ WARN(!svsb, "%s: svsb(%s) is null", __func__, svsb->name);
+
+ spin_lock_irqsave(&svs_lock, flags);
+ svsp->pbank = svsb;
+
+ /* Find out which svs bank fires interrupt */
+ if (svsb->int_st & svs_readl_relaxed(svsp, INTST)) {
+ spin_unlock_irqrestore(&svs_lock, flags);
+ continue;
+ }
+
+ svs_switch_bank(svsp);
+ int_sts = svs_readl_relaxed(svsp, INTSTS);
+ svs_en = svs_readl_relaxed(svsp, SVSEN);
+
+ if (int_sts == SVSB_INTSTS_COMPLETE &&
+ svs_en == SVSB_EN_INIT01)
+ svs_init01_isr_handler(svsp);
+ else if (int_sts == SVSB_INTSTS_COMPLETE &&
+ svs_en == SVSB_EN_INIT02)
+ svs_init02_isr_handler(svsp);
+ else
+ svs_error_isr_handler(svsp);
+
+ spin_unlock_irqrestore(&svs_lock, flags);
+ break;
+ }
+
+ svs_adjust_pm_opp_volts(svsb);
+
+ if (svsb->phase == SVSB_PHASE_INIT01 ||
+ svsb->phase == SVSB_PHASE_INIT02)
+ complete(&svsb->init_completion);
+
+ return IRQ_HANDLED;
+}
+
+static int svs_init01(struct svs_platform *svsp)
+{
+ struct svs_bank *svsb;
+ struct pm_qos_request *cpu_qos_request;
+ unsigned long flags, time_left;
+ bool search_done;
+ int ret = 0, r;
+ u32 opp_freq, opp_vboot, buck_volt, idx, i;
+
+ cpu_qos_request = kzalloc(sizeof(*cpu_qos_request), GFP_KERNEL);
+ if (!cpu_qos_request)
+ return -ENOMEM;
+
+ /* Let CPUs leave idle-off state for initializing svs_init01. */
+ cpu_latency_qos_add_request(cpu_qos_request, 0);
+
+ /* Svs bank init01 preparation - power enable */
+ for (idx = 0; idx < svsp->bank_max; idx++) {
+ svsb = &svsp->banks[idx];
+
+ if (!(svsb->mode_support & SVSB_MODE_INIT01))
+ continue;
+
+ ret = regulator_enable(svsb->buck);
+ if (ret) {
+ dev_err(svsb->dev, "%s enable fail: %d\n",
+ svsb->buck_name, ret);
+ goto init01_remove_cpu_qos_request;
+ }
+
+ /* Some buck doesn't support mode change. Show fail msg only */
+ ret = regulator_set_mode(svsb->buck, REGULATOR_MODE_FAST);
+ if (ret)
+ dev_notice(svsb->dev, "set fast mode fail: %d\n", ret);
+
+ if (svsb->volt_flags & SVSB_INIT01_PD_REQ) {
+ if (!pm_runtime_enabled(svsb->pd_dev)) {
+ pm_runtime_enable(svsb->pd_dev);
+ svsb->pm_runtime_enabled_count++;
+ }
+
+ ret = pm_runtime_get_sync(svsb->pd_dev);
+ if (ret < 0) {
+ dev_err(svsb->dev, "mtcmos on fail: %d\n", ret);
+ goto init01_remove_cpu_qos_request;
+ }
+ }
+ }
+
+ /*
+ * Svs bank init01 preparation - vboot voltage adjustment
+ * Sometimes two svs banks use the same buck. Therefore,
+ * we have to set each svs bank to target voltage(vboot) first.
+ */
+ for (idx = 0; idx < svsp->bank_max; idx++) {
+ svsb = &svsp->banks[idx];
+
+ if (!(svsb->mode_support & SVSB_MODE_INIT01))
+ continue;
+
+ /*
+ * Find the fastest freq that can be run at vboot and
+ * fix to that freq until svs_init01 is done.
+ */
+ search_done = false;
+ opp_vboot = svs_bank_volt_to_opp_volt(svsb->vboot,
+ svsb->volt_step,
+ svsb->volt_base);
+
+ for (i = 0; i < svsb->opp_count; i++) {
+ opp_freq = svsb->opp_dfreq[i];
+ if (!search_done && svsb->opp_dvolt[i] <= opp_vboot) {
+ ret = dev_pm_opp_adjust_voltage(svsb->opp_dev,
+ opp_freq,
+ opp_vboot,
+ opp_vboot,
+ opp_vboot);
+ if (ret) {
+ dev_err(svsb->dev,
+ "set opp %uuV vboot fail: %d\n",
+ opp_vboot, ret);
+ goto init01_finish;
+ }
+
+ search_done = true;
+ } else {
+ ret = dev_pm_opp_disable(svsb->opp_dev,
+ svsb->opp_dfreq[i]);
+ if (ret) {
+ dev_err(svsb->dev,
+ "opp %uHz disable fail: %d\n",
+ svsb->opp_dfreq[i], ret);
+ goto init01_finish;
+ }
+ }
+ }
+ }
+
+ /* Svs bank init01 begins */
+ for (idx = 0; idx < svsp->bank_max; idx++) {
+ svsb = &svsp->banks[idx];
+
+ if (!(svsb->mode_support & SVSB_MODE_INIT01))
+ continue;
+
+ opp_vboot = svs_bank_volt_to_opp_volt(svsb->vboot,
+ svsb->volt_step,
+ svsb->volt_base);
+
+ buck_volt = regulator_get_voltage(svsb->buck);
+ if (buck_volt != opp_vboot) {
+ dev_err(svsb->dev,
+ "buck voltage: %uuV, expected vboot: %uuV\n",
+ buck_volt, opp_vboot);
+ ret = -EPERM;
+ goto init01_finish;
+ }
+
+ spin_lock_irqsave(&svs_lock, flags);
+ svsp->pbank = svsb;
+ svs_set_bank_phase(svsp, SVSB_PHASE_INIT01);
+ spin_unlock_irqrestore(&svs_lock, flags);
+
+ time_left = wait_for_completion_timeout(&svsb->init_completion,
+ msecs_to_jiffies(5000));
+ if (!time_left) {
+ dev_err(svsb->dev, "init01 completion timeout\n");
+ ret = -EBUSY;
+ goto init01_finish;
+ }
+ }
+
+init01_finish:
+ for (idx = 0; idx < svsp->bank_max; idx++) {
+ svsb = &svsp->banks[idx];
+
+ if (!(svsb->mode_support & SVSB_MODE_INIT01))
+ continue;
+
+ for (i = 0; i < svsb->opp_count; i++) {
+ r = dev_pm_opp_enable(svsb->opp_dev,
+ svsb->opp_dfreq[i]);
+ if (r)
+ dev_err(svsb->dev, "opp %uHz enable fail: %d\n",
+ svsb->opp_dfreq[i], r);
+ }
+
+ if (svsb->volt_flags & SVSB_INIT01_PD_REQ) {
+ r = pm_runtime_put_sync(svsb->pd_dev);
+ if (r)
+ dev_err(svsb->dev, "mtcmos off fail: %d\n", r);
+
+ if (svsb->pm_runtime_enabled_count > 0) {
+ pm_runtime_disable(svsb->pd_dev);
+ svsb->pm_runtime_enabled_count--;
+ }
+ }
+
+ r = regulator_set_mode(svsb->buck, REGULATOR_MODE_NORMAL);
+ if (r)
+ dev_notice(svsb->dev, "set normal mode fail: %d\n", r);
+
+ r = regulator_disable(svsb->buck);
+ if (r)
+ dev_err(svsb->dev, "%s disable fail: %d\n",
+ svsb->buck_name, r);
+ }
+
+init01_remove_cpu_qos_request:
+ cpu_latency_qos_remove_request(cpu_qos_request);
+ kfree(cpu_qos_request);
+
+ return ret;
+}
+
+static int svs_init02(struct svs_platform *svsp)
+{
+ struct svs_bank *svsb;
+ unsigned long flags, time_left;
+ u32 idx;
+
+ for (idx = 0; idx < svsp->bank_max; idx++) {
+ svsb = &svsp->banks[idx];
+
+ if (!(svsb->mode_support & SVSB_MODE_INIT02))
+ continue;
+
+ reinit_completion(&svsb->init_completion);
+ spin_lock_irqsave(&svs_lock, flags);
+ svsp->pbank = svsb;
+ svs_set_bank_phase(svsp, SVSB_PHASE_INIT02);
+ spin_unlock_irqrestore(&svs_lock, flags);
+
+ time_left = wait_for_completion_timeout(&svsb->init_completion,
+ msecs_to_jiffies(5000));
+ if (!time_left) {
+ dev_err(svsb->dev, "init02 completion timeout\n");
+ return -EBUSY;
+ }
+ }
+
+ return 0;
+}
+
+static int svs_start(struct svs_platform *svsp)
+{
+ int ret;
+
+ ret = svs_init01(svsp);
+ if (ret)
+ return ret;
+
+ ret = svs_init02(svsp);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int svs_suspend(struct device *dev)
+{
+ struct svs_platform *svsp = dev_get_drvdata(dev);
+ struct svs_bank *svsb;
+ unsigned long flags;
+ u32 idx;
+
+ for (idx = 0; idx < svsp->bank_max; idx++) {
+ svsb = &svsp->banks[idx];
+
+ /* This might wait for svs_isr() process */
+ spin_lock_irqsave(&svs_lock, flags);
+ svsp->pbank = svsb;
+ svs_switch_bank(svsp);
+ svs_writel_relaxed(svsp, SVSB_EN_OFF, SVSEN);
+ svs_writel_relaxed(svsp, SVSB_INTSTS_CLEAN, INTSTS);
+ spin_unlock_irqrestore(&svs_lock, flags);
+
+ svsb->phase = SVSB_PHASE_ERROR;
+ svs_adjust_pm_opp_volts(svsb);
+ }
+
+ clk_disable_unprepare(svsp->main_clk);
+
+ return 0;
+}
+
+static int svs_resume(struct device *dev)
+{
+ struct svs_platform *svsp = dev_get_drvdata(dev);
+ int ret;
+
+ ret = clk_prepare_enable(svsp->main_clk);
+ if (ret) {
+ dev_err(svsp->dev, "cannot enable main_clk, disable svs\n");
+ return ret;
+ }
+
+ ret = svs_init02(svsp);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int svs_bank_resource_setup(struct svs_platform *svsp)
+{
+ struct svs_bank *svsb;
+ struct dev_pm_opp *opp;
+ unsigned long freq;
+ int count, ret;
+ u32 idx, i;
+
+ dev_set_drvdata(svsp->dev, svsp);
+
+ for (idx = 0; idx < svsp->bank_max; idx++) {
+ svsb = &svsp->banks[idx];
+
+ switch (svsb->sw_id) {
+ case SVSB_CPU_LITTLE:
+ svsb->name = "SVSB_CPU_LITTLE";
+ break;
+ case SVSB_CPU_BIG:
+ svsb->name = "SVSB_CPU_BIG";
+ break;
+ case SVSB_CCI:
+ svsb->name = "SVSB_CCI";
+ break;
+ case SVSB_GPU:
+ svsb->name = "SVSB_GPU";
+ break;
+ default:
+ dev_err(svsb->dev, "unknown sw_id: %u\n", svsb->sw_id);
+ return -EINVAL;
+ }
+
+ svsb->dev = devm_kzalloc(svsp->dev, sizeof(*svsb->dev),
+ GFP_KERNEL);
+ if (!svsb->dev)
+ return -ENOMEM;
+
+ ret = dev_set_name(svsb->dev, "%s", svsb->name);
+ if (ret)
+ return ret;
+
+ dev_set_drvdata(svsb->dev, svsp);
+
+ ret = dev_pm_opp_of_add_table(svsb->opp_dev);
+ if (ret) {
+ dev_err(svsb->dev, "add opp table fail: %d\n", ret);
+ return ret;
+ }
+
+ mutex_init(&svsb->lock);
+ init_completion(&svsb->init_completion);
+
+ if (svsb->mode_support & SVSB_MODE_INIT01) {
+ svsb->buck = devm_regulator_get_optional(svsb->opp_dev,
+ svsb->buck_name);
+ if (IS_ERR(svsb->buck)) {
+ dev_err(svsb->dev, "cannot get \"%s-supply\"\n",
+ svsb->buck_name);
+ return PTR_ERR(svsb->buck);
+ }
+ }
+
+ count = dev_pm_opp_get_opp_count(svsb->opp_dev);
+ if (svsb->opp_count != count) {
+ dev_err(svsb->dev,
+ "opp_count not \"%u\" but get \"%d\"?\n",
+ svsb->opp_count, count);
+ return count;
+ }
+
+ for (i = 0, freq = U32_MAX; i < svsb->opp_count; i++, freq--) {
+ opp = dev_pm_opp_find_freq_floor(svsb->opp_dev, &freq);
+ if (IS_ERR(opp)) {
+ dev_err(svsb->dev, "cannot find freq = %ld\n",
+ PTR_ERR(opp));
+ return PTR_ERR(opp);
+ }
+
+ svsb->opp_dfreq[i] = freq;
+ svsb->opp_dvolt[i] = dev_pm_opp_get_voltage(opp);
+ svsb->freq_pct[i] = percent(svsb->opp_dfreq[i],
+ svsb->freq_base);
+ dev_pm_opp_put(opp);
+ }
+ }
+
+ return 0;
+}
+
+static bool svs_mt8183_efuse_parsing(struct svs_platform *svsp)
+{
+ struct svs_bank *svsb;
+ u32 idx, i, ft_pgm;
+
+ for (i = 0; i < svsp->efuse_max; i++)
+ if (svsp->efuse[i])
+ dev_info(svsp->dev, "M_HW_RES%d: 0x%08x\n",
+ i, svsp->efuse[i]);
+
+ if (!svsp->efuse[2]) {
+ dev_notice(svsp->dev, "svs_efuse[2] = 0x0?\n");
+ return false;
+ }
+
+ /* Svs efuse parsing */
+ ft_pgm = (svsp->efuse[0] >> 4) & GENMASK(3, 0);
+
+ for (idx = 0; idx < svsp->bank_max; idx++) {
+ svsb = &svsp->banks[idx];
+
+ if (ft_pgm <= 1)
+ svsb->volt_flags |= SVSB_INIT01_VOLT_IGNORE;
+
+ switch (svsb->sw_id) {
+ case SVSB_CPU_LITTLE:
+ svsb->bdes = svsp->efuse[16] & GENMASK(7, 0);
+ svsb->mdes = (svsp->efuse[16] >> 8) & GENMASK(7, 0);
+ svsb->dcbdet = (svsp->efuse[16] >> 16) & GENMASK(7, 0);
+ svsb->dcmdet = (svsp->efuse[16] >> 24) & GENMASK(7, 0);
+ svsb->mtdes = (svsp->efuse[17] >> 16) & GENMASK(7, 0);
+
+ if (ft_pgm <= 3)
+ svsb->volt_od += 10;
+ else
+ svsb->volt_od += 2;
+ break;
+ case SVSB_CPU_BIG:
+ svsb->bdes = svsp->efuse[18] & GENMASK(7, 0);
+ svsb->mdes = (svsp->efuse[18] >> 8) & GENMASK(7, 0);
+ svsb->dcbdet = (svsp->efuse[18] >> 16) & GENMASK(7, 0);
+ svsb->dcmdet = (svsp->efuse[18] >> 24) & GENMASK(7, 0);
+ svsb->mtdes = svsp->efuse[17] & GENMASK(7, 0);
+
+ if (ft_pgm <= 3)
+ svsb->volt_od += 15;
+ else
+ svsb->volt_od += 12;
+ break;
+ case SVSB_CCI:
+ svsb->bdes = svsp->efuse[4] & GENMASK(7, 0);
+ svsb->mdes = (svsp->efuse[4] >> 8) & GENMASK(7, 0);
+ svsb->dcbdet = (svsp->efuse[4] >> 16) & GENMASK(7, 0);
+ svsb->dcmdet = (svsp->efuse[4] >> 24) & GENMASK(7, 0);
+ svsb->mtdes = (svsp->efuse[5] >> 16) & GENMASK(7, 0);
+
+ if (ft_pgm <= 3)
+ svsb->volt_od += 10;
+ else
+ svsb->volt_od += 2;
+ break;
+ case SVSB_GPU:
+ svsb->bdes = svsp->efuse[6] & GENMASK(7, 0);
+ svsb->mdes = (svsp->efuse[6] >> 8) & GENMASK(7, 0);
+ svsb->dcbdet = (svsp->efuse[6] >> 16) & GENMASK(7, 0);
+ svsb->dcmdet = (svsp->efuse[6] >> 24) & GENMASK(7, 0);
+ svsb->mtdes = svsp->efuse[5] & GENMASK(7, 0);
+
+ if (ft_pgm >= 2) {
+ svsb->freq_base = 800000000; /* 800MHz */
+ svsb->dvt_fixed = 2;
+ }
+ break;
+ default:
+ dev_err(svsb->dev, "unknown sw_id: %u\n", svsb->sw_id);
+ return false;
+ }
+ }
+
+ return true;
+}
+
+static bool svs_is_efuse_data_correct(struct svs_platform *svsp)
+{
+ struct nvmem_cell *cell;
+
+ /* Get svs efuse by nvmem */
+ cell = nvmem_cell_get(svsp->dev, "svs-calibration-data");
+ if (IS_ERR(cell)) {
+ dev_err(svsp->dev, "no \"svs-calibration-data\"? %ld\n",
+ PTR_ERR(cell));
+ return false;
+ }
+
+ svsp->efuse = nvmem_cell_read(cell, &svsp->efuse_max);
+ if (IS_ERR(svsp->efuse)) {
+ dev_err(svsp->dev, "cannot read svs efuse: %ld\n",
+ PTR_ERR(svsp->efuse));
+ return false;
+ }
+
+ svsp->efuse_max /= sizeof(u32);
+ nvmem_cell_put(cell);
+
+ return svsp->efuse_parsing(svsp);
+}
+
+static struct device *svs_get_subsys_device(struct svs_platform *svsp,
+ const char *node_name)
+{
+ struct platform_device *pdev;
+ struct device_node *np;
+
+ np = of_find_node_by_name(NULL, node_name);
+ if (!np) {
+ dev_err(svsp->dev, "cannot find %s node\n", node_name);
+ return ERR_PTR(-ENODEV);
+ }
+
+ pdev = of_find_device_by_node(np);
+ if (!pdev) {
+ of_node_put(np);
+ dev_err(svsp->dev, "cannot find pdev by %s\n", node_name);
+ return ERR_PTR(-ENXIO);
+ }
+
+ of_node_put(np);
+
+ return &pdev->dev;
+}
+
+static struct device *svs_add_device_link(struct svs_platform *svsp,
+ const char *node_name)
+{
+ struct device *dev;
+ struct device_link *sup_link;
+
+ if (!node_name) {
+ dev_err(svsp->dev, "node name cannot be null\n");
+ return ERR_PTR(-EINVAL);
+ }
+
+ dev = svs_get_subsys_device(svsp, node_name);
+ if (IS_ERR(dev))
+ return dev;
+
+ sup_link = device_link_add(svsp->dev, dev,
+ DL_FLAG_AUTOREMOVE_CONSUMER);
+ if (!sup_link) {
+ dev_err(svsp->dev, "sup_link is NULL\n");
+ return ERR_PTR(-EINVAL);
+ }
+
+ if (sup_link->supplier->links.status != DL_DEV_DRIVER_BOUND)
+ return ERR_PTR(-EPROBE_DEFER);
+
+ return dev;
+}
+
+static int svs_mt8183_platform_probe(struct svs_platform *svsp)
+{
+ struct svs_bank *svsb;
+ u32 idx;
+
+ for (idx = 0; idx < svsp->bank_max; idx++) {
+ svsb = &svsp->banks[idx];
+
+ switch (svsb->sw_id) {
+ case SVSB_CPU_LITTLE:
+ case SVSB_CPU_BIG:
+ svsb->opp_dev = get_cpu_device(svsb->cpu_id);
+ break;
+ case SVSB_CCI:
+ svsb->opp_dev = svs_add_device_link(svsp, "cci");
+ break;
+ case SVSB_GPU:
+ svsb->opp_dev = svs_add_device_link(svsp, "mali");
+ svsb->pd_dev = svs_add_device_link(svsp, "mali_gpu_core2");
+ if (IS_ERR(svsb->pd_dev))
+ return PTR_ERR(svsb->pd_dev);
+ break;
+ default:
+ dev_err(svsb->dev, "unknown sw_id: %u\n", svsb->sw_id);
+ return -EINVAL;
+ }
+
+ if (IS_ERR(svsb->opp_dev))
+ return PTR_ERR(svsb->opp_dev);
+ }
+
+ return 0;
+}
+
+static struct svs_bank svs_mt8183_banks[] = {
+ {
+ .sw_id = SVSB_CPU_LITTLE,
+ .set_freq_pct = svs_set_bank_freq_pct_v2,
+ .get_volts = svs_get_bank_volts_v2,
+ .cpu_id = 0,
+ .buck_name = "proc",
+ .volt_flags = SVSB_INIT01_VOLT_INC_ONLY,
+ .mode_support = SVSB_MODE_INIT01 | SVSB_MODE_INIT02,
+ .opp_count = MAX_OPP_ENTRIES,
+ .freq_base = 1989000000,
+ .vboot = 0x30,
+ .volt_step = 6250,
+ .volt_base = 500000,
+ .vmax = 0x64,
+ .vmin = 0x18,
+ .age_config = 0x555555,
+ .dc_config = 0x555555,
+ .dvt_fixed = 0x7,
+ .vco = 0x10,
+ .chk_shift = 0x77,
+ .core_sel = 0x8fff0000,
+ .int_st = BIT(0),
+ .ctl0 = 0x00010001,
+ },
+ {
+ .sw_id = SVSB_CPU_BIG,
+ .set_freq_pct = svs_set_bank_freq_pct_v2,
+ .get_volts = svs_get_bank_volts_v2,
+ .cpu_id = 4,
+ .buck_name = "proc",
+ .volt_flags = SVSB_INIT01_VOLT_INC_ONLY,
+ .mode_support = SVSB_MODE_INIT01 | SVSB_MODE_INIT02,
+ .opp_count = MAX_OPP_ENTRIES,
+ .freq_base = 1989000000,
+ .vboot = 0x30,
+ .volt_step = 6250,
+ .volt_base = 500000,
+ .vmax = 0x58,
+ .vmin = 0x10,
+ .age_config = 0x555555,
+ .dc_config = 0x555555,
+ .dvt_fixed = 0x7,
+ .vco = 0x10,
+ .chk_shift = 0x77,
+ .core_sel = 0x8fff0001,
+ .int_st = BIT(1),
+ .ctl0 = 0x00000001,
+ },
+ {
+ .sw_id = SVSB_CCI,
+ .set_freq_pct = svs_set_bank_freq_pct_v2,
+ .get_volts = svs_get_bank_volts_v2,
+ .buck_name = "proc",
+ .volt_flags = SVSB_INIT01_VOLT_INC_ONLY,
+ .mode_support = SVSB_MODE_INIT01 | SVSB_MODE_INIT02,
+ .opp_count = MAX_OPP_ENTRIES,
+ .freq_base = 1196000000,
+ .vboot = 0x30,
+ .volt_step = 6250,
+ .volt_base = 500000,
+ .vmax = 0x64,
+ .vmin = 0x18,
+ .age_config = 0x555555,
+ .dc_config = 0x555555,
+ .dvt_fixed = 0x7,
+ .vco = 0x10,
+ .chk_shift = 0x77,
+ .core_sel = 0x8fff0002,
+ .int_st = BIT(2),
+ .ctl0 = 0x00100003,
+ },
+ {
+ .sw_id = SVSB_GPU,
+ .set_freq_pct = svs_set_bank_freq_pct_v2,
+ .get_volts = svs_get_bank_volts_v2,
+ .buck_name = "mali",
+ .volt_flags = SVSB_INIT01_PD_REQ |
+ SVSB_INIT01_VOLT_INC_ONLY,
+ .mode_support = SVSB_MODE_INIT01 | SVSB_MODE_INIT02,
+ .opp_count = MAX_OPP_ENTRIES,
+ .freq_base = 900000000,
+ .vboot = 0x30,
+ .volt_step = 6250,
+ .volt_base = 500000,
+ .vmax = 0x40,
+ .vmin = 0x14,
+ .age_config = 0x555555,
+ .dc_config = 0x555555,
+ .dvt_fixed = 0x3,
+ .vco = 0x10,
+ .chk_shift = 0x77,
+ .core_sel = 0x8fff0003,
+ .int_st = BIT(3),
+ .ctl0 = 0x00050001,
+ },
+};
+
+static const struct svs_platform_data svs_mt8183_platform_data = {
+ .name = "mt8183-svs",
+ .banks = svs_mt8183_banks,
+ .efuse_parsing = svs_mt8183_efuse_parsing,
+ .probe = svs_mt8183_platform_probe,
+ .irqflags = IRQF_TRIGGER_LOW,
+ .regs = svs_regs_v2,
+ .bank_max = ARRAY_SIZE(svs_mt8183_banks),
+};
+
+static const struct of_device_id svs_of_match[] = {
+ {
+ .compatible = "mediatek,mt8183-svs",
+ .data = &svs_mt8183_platform_data,
+ }, {
+ /* Sentinel */
+ },
+};
+
+static struct svs_platform *svs_platform_probe(struct platform_device *pdev)
+{
+ struct svs_platform *svsp;
+ const struct svs_platform_data *svsp_data;
+ int ret;
+
+ svsp_data = of_device_get_match_data(&pdev->dev);
+ if (!svsp_data) {
+ dev_err(&pdev->dev, "no svs platform data?\n");
+ return ERR_PTR(-EPERM);
+ }
+
+ svsp = devm_kzalloc(&pdev->dev, sizeof(*svsp), GFP_KERNEL);
+ if (!svsp)
+ return ERR_PTR(-ENOMEM);
+
+ svsp->dev = &pdev->dev;
+ svsp->name = svsp_data->name;
+ svsp->banks = svsp_data->banks;
+ svsp->efuse_parsing = svsp_data->efuse_parsing;
+ svsp->probe = svsp_data->probe;
+ svsp->irqflags = svsp_data->irqflags;
+ svsp->regs = svsp_data->regs;
+ svsp->bank_max = svsp_data->bank_max;
+
+ ret = svsp->probe(svsp);
+ if (ret)
+ return ERR_PTR(ret);
+
+ return svsp;
+}
+
+static int svs_probe(struct platform_device *pdev)
+{
+ struct svs_platform *svsp;
+ unsigned int svsp_irq;
+ int ret;
+
+ svsp = svs_platform_probe(pdev);
+ if (IS_ERR(svsp)) {
+ dev_err_probe(&pdev->dev, PTR_ERR(svsp),
+ "svs platform probe fail\n");
+ return PTR_ERR(svsp);
+ }
+
+ if (!svs_is_efuse_data_correct(svsp)) {
+ dev_notice(svsp->dev, "efuse data isn't correct\n");
+ return -EPERM;
+ }
+
+ ret = svs_bank_resource_setup(svsp);
+ if (ret) {
+ dev_err(svsp->dev, "svs bank resource setup fail: %d\n", ret);
+ return ret;
+ }
+
+ svsp_irq = irq_of_parse_and_map(svsp->dev->of_node, 0);
+ ret = devm_request_threaded_irq(svsp->dev, svsp_irq, NULL, svs_isr,
+ svsp->irqflags | IRQF_ONESHOT,
+ svsp->name, svsp);
+ if (ret) {
+ dev_err(svsp->dev, "register irq(%d) failed: %d\n",
+ svsp_irq, ret);
+ return ret;
+ }
+
+ svsp->main_clk = devm_clk_get(svsp->dev, "main");
+ if (IS_ERR(svsp->main_clk)) {
+ dev_err(svsp->dev, "failed to get clock: %ld\n",
+ PTR_ERR(svsp->main_clk));
+ return PTR_ERR(svsp->main_clk);
+ }
+
+ ret = clk_prepare_enable(svsp->main_clk);
+ if (ret) {
+ dev_err(svsp->dev, "cannot enable main clk: %d\n", ret);
+ return ret;
+ }
+
+ svsp->base = of_iomap(svsp->dev->of_node, 0);
+ if (IS_ERR_OR_NULL(svsp->base)) {
+ dev_err(svsp->dev, "cannot find svs register base\n");
+ ret = -EINVAL;
+ goto svs_probe_clk_disable;
+ }
+
+ ret = svs_start(svsp);
+ if (ret) {
+ dev_err(svsp->dev, "svs start fail: %d\n", ret);
+ goto svs_probe_iounmap;
+ }
+
+ return 0;
+
+svs_probe_iounmap:
+ iounmap(svsp->base);
+
+svs_probe_clk_disable:
+ clk_disable_unprepare(svsp->main_clk);
+
+ return ret;
+}
+
+static SIMPLE_DEV_PM_OPS(svs_pm_ops, svs_suspend, svs_resume);
+
+static struct platform_driver svs_driver = {
+ .probe = svs_probe,
+ .driver = {
+ .name = "mtk-svs",
+ .pm = &svs_pm_ops,
+ .of_match_table = of_match_ptr(svs_of_match),
+ },
+};
+
+module_platform_driver(svs_driver);
+
+MODULE_AUTHOR("Roger Lu <roger.lu at mediatek.com>");
+MODULE_DESCRIPTION("MediaTek SVS driver");
+MODULE_LICENSE("GPL v2");
--
2.18.0
More information about the Linux-mediatek
mailing list