[PATCH v21 8/8] soc: mediatek: SVS: add mt8192 SVS GPU driver

Roger Lu roger.lu at mediatek.com
Fri Jan 7 01:52:00 PST 2022


mt8192 SVS GPU uses 2-line (high/low bank) HW architecture to provide
bank voltages. High bank helps update higher frequency's voltage
and low bank helps update lower frequency's voltage.

Signed-off-by: Roger Lu <roger.lu at mediatek.com>
---
 drivers/soc/mediatek/mtk-svs.c | 469 ++++++++++++++++++++++++++++++++-
 1 file changed, 464 insertions(+), 5 deletions(-)

diff --git a/drivers/soc/mediatek/mtk-svs.c b/drivers/soc/mediatek/mtk-svs.c
index 93cdaecadd6d..bec6524ab33a 100644
--- a/drivers/soc/mediatek/mtk-svs.c
+++ b/drivers/soc/mediatek/mtk-svs.c
@@ -24,6 +24,7 @@
 #include <linux/pm_qos.h>
 #include <linux/pm_runtime.h>
 #include <linux/regulator/consumer.h>
+#include <linux/reset.h>
 #include <linux/seq_file.h>
 #include <linux/slab.h>
 #include <linux/spinlock.h>
@@ -35,6 +36,10 @@
 #define SVSB_CCI			BIT(2)
 #define SVSB_GPU			BIT(3)
 
+/* svs bank 2-line type */
+#define SVSB_LOW			BIT(8)
+#define SVSB_HIGH			BIT(9)
+
 /* svs bank mode support */
 #define SVSB_MODE_ALL_DISABLE		0
 #define SVSB_MODE_INIT01		BIT(1)
@@ -45,6 +50,8 @@
 #define SVSB_INIT01_PD_REQ		BIT(0)
 #define SVSB_INIT01_VOLT_IGNORE		BIT(1)
 #define SVSB_INIT01_VOLT_INC_ONLY	BIT(2)
+#define SVSB_MON_VOLT_IGNORE		BIT(16)
+#define SVSB_REMOVE_DVTFIXED_VOLT	BIT(24)
 
 /* svs bank common setting */
 #define MAX_OPP_ENTRIES			16
@@ -249,6 +256,7 @@ static const u32 svs_regs_v2[] = {
  * @main_clk: main clock for svs bank
  * @pbank: svs bank pointer protected by spin_lock section
  * @banks: svs banks that svs platform supports
+ * @rst: svs platform reset control
  * @efuse_parsing: svs platform efuse parsing function pointer
  * @probe: svs platform probe function pointer
  * @irqflags: svs platform irq settings flags
@@ -266,6 +274,7 @@ struct svs_platform {
 	struct clk *main_clk;
 	struct svs_bank *pbank;
 	struct svs_bank *banks;
+	struct reset_control *rst;
 	bool (*efuse_parsing)(struct svs_platform *svsp);
 	int (*probe)(struct svs_platform *svsp);
 	unsigned long irqflags;
@@ -298,6 +307,7 @@ struct svs_platform {
  * @pm_runtime_enabled_count: bank pm runtime enabled count
  * @mode_support: bank mode support.
  * @freq_base: reference frequency for bank init
+ * @turn_freq_base: refenrece frequency for turn point
  * @vboot: voltage request for bank init01 only
  * @opp_dfreq: default opp frequency table
  * @opp_dvolt: default opp voltage table
@@ -333,6 +343,8 @@ struct svs_platform {
  * @mtdes: svs efuse data
  * @dcbdet: svs efuse data
  * @dcmdet: svs efuse data
+ * @turn_pt: turn point informs which opp_volt calculated by high/low bank.
+ * @type: bank type to represent it is 2-line (high/low) bank or 1-line bank.
  *
  * Svs bank will generate suitalbe voltages by below general math equation
  * and provide these voltages to opp voltage table.
@@ -359,6 +371,7 @@ struct svs_bank {
 	u32 pm_runtime_enabled_count;
 	u32 mode_support;
 	u32 freq_base;
+	u32 turn_freq_base;
 	u32 vboot;
 	u32 opp_dfreq[MAX_OPP_ENTRIES];
 	u32 opp_dvolt[MAX_OPP_ENTRIES];
@@ -394,6 +407,8 @@ struct svs_bank {
 	u32 mtdes;
 	u32 dcbdet;
 	u32 dcmdet;
+	u32 turn_pt;
+	u32 type;
 };
 
 static u32 percent(u32 numerator, u32 denominator)
@@ -429,6 +444,37 @@ static u32 svs_bank_volt_to_opp_volt(u32 svsb_volt, u32 svsb_volt_step,
 	return (svsb_volt * svsb_volt_step) + svsb_volt_base;
 }
 
+static u32 svs_opp_volt_to_bank_volt(u32 opp_u_volt, u32 svsb_volt_step,
+				     u32 svsb_volt_base)
+{
+	return (opp_u_volt - svsb_volt_base) / svsb_volt_step;
+}
+
+static int svs_sync_bank_volts_from_opp(struct svs_bank *svsb)
+{
+	struct dev_pm_opp *opp;
+	u32 i, opp_u_volt;
+
+	for (i = 0; i < svsb->opp_count; i++) {
+		opp = dev_pm_opp_find_freq_exact(svsb->opp_dev,
+						 svsb->opp_dfreq[i],
+						 true);
+		if (IS_ERR(opp)) {
+			dev_err(svsb->dev, "cannot find freq = %u (%ld)\n",
+				svsb->opp_dfreq[i], PTR_ERR(opp));
+			return PTR_ERR(opp);
+		}
+
+		opp_u_volt = dev_pm_opp_get_voltage(opp);
+		svsb->volt[i] = svs_opp_volt_to_bank_volt(opp_u_volt,
+							  svsb->volt_step,
+							  svsb->volt_base);
+		dev_pm_opp_put(opp);
+	}
+
+	return 0;
+}
+
 static int svs_get_zone_temperature(const char *tzone_name, int *tzone_temp)
 {
 	struct thermal_zone_device *tzd;
@@ -443,7 +489,7 @@ static int svs_get_zone_temperature(const char *tzone_name, int *tzone_temp)
 static int svs_adjust_pm_opp_volts(struct svs_bank *svsb, bool force_update)
 {
 	int ret = -EPERM, tzone_temp = 0;
-	u32 i, svsb_volt, opp_volt, temp_voffset = 0;
+	u32 i, svsb_volt, opp_volt, temp_voffset = 0, opp_start, opp_stop;
 
 	mutex_lock(&svsb->lock);
 
@@ -457,6 +503,21 @@ static int svs_adjust_pm_opp_volts(struct svs_bank *svsb, bool force_update)
 		goto unlock_mutex;
 	}
 
+	/*
+	 * 2-line bank updates its corresponding opp volts.
+	 * 1-line bank updates all opp volts.
+	 */
+	if (svsb->type == SVSB_HIGH) {
+		opp_start = 0;
+		opp_stop = svsb->turn_pt;
+	} else if (svsb->type == SVSB_LOW) {
+		opp_start = svsb->turn_pt;
+		opp_stop = svsb->opp_count;
+	} else {
+		opp_start = 0;
+		opp_stop = svsb->opp_count;
+	}
+
 	/* Get thermal effect */
 	if (svsb->phase == SVSB_PHASE_MON) {
 		ret = svs_get_zone_temperature(svsb->tzone_name, &tzone_temp);
@@ -471,10 +532,16 @@ static int svs_adjust_pm_opp_volts(struct svs_bank *svsb, bool force_update)
 			temp_voffset += svsb->tzone_htemp_voffset;
 		else if (tzone_temp <= svsb->tzone_ltemp)
 			temp_voffset += svsb->tzone_ltemp_voffset;
+
+		/* 2-line bank update all opp volts when running mode */
+		if (svsb->type == SVSB_HIGH || svsb->type == SVSB_LOW) {
+			opp_start = 0;
+			opp_stop = svsb->opp_count;
+		}
 	}
 
 	/* vmin <= svsb_volt (opp_volt) <= default opp voltage */
-	for (i = 0; i < svsb->opp_count; i++) {
+	for (i = opp_start; i < opp_stop; i++) {
 		switch (svsb->phase) {
 		case SVSB_PHASE_ERROR:
 			opp_volt = svsb->opp_dvolt[i];
@@ -639,9 +706,11 @@ static int svs_status_debug_show(struct seq_file *m, void *v)
 
 	ret = svs_get_zone_temperature(svsb->tzone_name, &tzone_temp);
 	if (ret)
-		seq_printf(m, "%s: temperature ignore\n", svsb->name);
+		seq_printf(m, "%s: temperature ignore, turn_pt = %u\n",
+			   svsb->name, svsb->turn_pt);
 	else
-		seq_printf(m, "%s: temperature = %d\n", svsb->name, tzone_temp);
+		seq_printf(m, "%s: temperature = %d, turn_pt = %u\n",
+			   svsb->name, tzone_temp, svsb->turn_pt);
 
 	for (i = 0; i < svsb->opp_count; i++) {
 		opp = dev_pm_opp_find_freq_exact(svsb->opp_dev,
@@ -784,6 +853,181 @@ static u32 interpolate(u32 f0, u32 f1, u32 v0, u32 v1, u32 fx)
 	return DIV_ROUND_UP(vx, 100);
 }
 
+static void svs_get_bank_volts_v3(struct svs_platform *svsp)
+{
+	struct svs_bank *svsb = svsp->pbank;
+	u32 i, j, *vop, vop74, vop30, mask7_0 = GENMASK(7, 0);
+	u32 b_sft, bits8 = 8, shift_byte = 0, reg_bytes = 4;
+	u32 middle_index = (svsb->opp_count / 2);
+	u32 opp_start = 0, opp_stop = 0, turn_pt = svsb->turn_pt;
+
+	if (svsb->phase == SVSB_PHASE_MON &&
+	    svsb->volt_flags & SVSB_MON_VOLT_IGNORE)
+		return;
+
+	vop74 = svs_readl_relaxed(svsp, VOP74);
+	vop30 = svs_readl_relaxed(svsp, VOP30);
+
+	/* Target is to set svsb->volt[] by algorithm */
+	if (turn_pt < middle_index) {
+		if (svsb->type == SVSB_HIGH) {
+			/* volt[0] ~ volt[turn_pt - 1] */
+			for (i = 0; i < turn_pt; i++) {
+				b_sft = bits8 * (shift_byte % reg_bytes);
+				vop = (shift_byte < reg_bytes) ? &vop30 :
+								 &vop74;
+				svsb->volt[i] = (*vop >> b_sft) & mask7_0;
+				shift_byte++;
+			}
+		} else if (svsb->type == SVSB_LOW) {
+			/* volt[turn_pt] + volt[j] ~ volt[opp_count - 1] */
+			j = svsb->opp_count - 7;
+			svsb->volt[turn_pt] = vop30 & mask7_0;
+			shift_byte++;
+			for (i = j; i < svsb->opp_count; i++) {
+				b_sft = bits8 * (shift_byte % reg_bytes);
+				vop = (shift_byte < reg_bytes) ? &vop30 :
+								 &vop74;
+				svsb->volt[i] = (*vop >> b_sft) & mask7_0;
+				shift_byte++;
+			}
+
+			/* volt[turn_pt + 1] ~ volt[j - 1] by interpolate */
+			for (i = turn_pt + 1; i < j; i++)
+				svsb->volt[i] =
+					interpolate(svsb->freq_pct[turn_pt],
+						    svsb->freq_pct[j],
+						    svsb->volt[turn_pt],
+						    svsb->volt[j],
+						    svsb->freq_pct[i]);
+		}
+	} else {
+		if (svsb->type == SVSB_HIGH) {
+			/* volt[0] + volt[j] ~ volt[turn_pt - 1] */
+			j = turn_pt - 7;
+			svsb->volt[0] = vop30 & mask7_0;
+			shift_byte++;
+			for (i = j; i < turn_pt; i++) {
+				b_sft = bits8 * (shift_byte % reg_bytes);
+				vop = (shift_byte < reg_bytes) ? &vop30 :
+								 &vop74;
+				svsb->volt[i] = (*vop >> b_sft) & mask7_0;
+				shift_byte++;
+			}
+
+			/* volt[1] ~ volt[j - 1] by interpolate */
+			for (i = 1; i < j; i++)
+				svsb->volt[i] =
+					interpolate(svsb->freq_pct[0],
+						    svsb->freq_pct[j],
+						    svsb->volt[0],
+						    svsb->volt[j],
+						    svsb->freq_pct[i]);
+		} else if (svsb->type == SVSB_LOW) {
+			/* volt[turn_pt] ~ volt[opp_count - 1] */
+			for (i = turn_pt; i < svsb->opp_count; i++) {
+				b_sft = bits8 * (shift_byte % reg_bytes);
+				vop = (shift_byte < reg_bytes) ? &vop30 :
+								 &vop74;
+				svsb->volt[i] = (*vop >> b_sft) & mask7_0;
+				shift_byte++;
+			}
+		}
+	}
+
+	if (svsb->type == SVSB_HIGH) {
+		opp_start = 0;
+		opp_stop = svsb->turn_pt;
+	} else if (svsb->type == SVSB_LOW) {
+		opp_start = svsb->turn_pt;
+		opp_stop = svsb->opp_count;
+	}
+
+	for (i = opp_start; i < opp_stop; i++)
+		if (svsb->volt_flags & SVSB_REMOVE_DVTFIXED_VOLT)
+			svsb->volt[i] -= svsb->dvt_fixed;
+}
+
+static void svs_set_bank_freq_pct_v3(struct svs_platform *svsp)
+{
+	struct svs_bank *svsb = svsp->pbank;
+	u32 i, j, *freq_pct, freq_pct74 = 0, freq_pct30 = 0;
+	u32 b_sft, bits8 = 8, shift_byte = 0, reg_bytes = 4;
+	u32 middle_index = (svsb->opp_count / 2);
+	u32 turn_pt = middle_index;
+
+	for (i = 0; i < svsb->opp_count; i++) {
+		if (svsb->opp_dfreq[i] <= svsb->turn_freq_base) {
+			svsb->turn_pt = i;
+			break;
+		}
+	}
+
+	turn_pt = svsb->turn_pt;
+
+	/* Target is to fill out freq_pct74 / freq_pct30 by algorithm */
+	if (turn_pt < middle_index) {
+		if (svsb->type == SVSB_HIGH) {
+			/* Edge case for preventing freq_pct30 from being 0 */
+			if (turn_pt == 0)
+				freq_pct30 = svsb->freq_pct[0];
+
+			/* freq_pct[0] ~ freq_pct[turn_pt - 1] */
+			for (i = 0; i < turn_pt; i++) {
+				b_sft = bits8 * (shift_byte % reg_bytes);
+				freq_pct = (shift_byte < reg_bytes) ?
+					   &freq_pct30 : &freq_pct74;
+				*freq_pct |= (svsb->freq_pct[i] << b_sft);
+				shift_byte++;
+			}
+		} else if (svsb->type == SVSB_LOW) {
+			/*
+			 * freq_pct[turn_pt] +
+			 * freq_pct[opp_count - 7] ~ freq_pct[opp_count -1]
+			 */
+			freq_pct30 = svsb->freq_pct[turn_pt];
+			shift_byte++;
+			j = svsb->opp_count - 7;
+			for (i = j; i < svsb->opp_count; i++) {
+				b_sft = bits8 * (shift_byte % reg_bytes);
+				freq_pct = (shift_byte < reg_bytes) ?
+					   &freq_pct30 : &freq_pct74;
+				*freq_pct |= (svsb->freq_pct[i] << b_sft);
+				shift_byte++;
+			}
+		}
+	} else {
+		if (svsb->type == SVSB_HIGH) {
+			/*
+			 * freq_pct[0] +
+			 * freq_pct[turn_pt - 7] ~ freq_pct[turn_pt - 1]
+			 */
+			freq_pct30 = svsb->freq_pct[0];
+			shift_byte++;
+			j = turn_pt - 7;
+			for (i = j; i < turn_pt; i++) {
+				b_sft = bits8 * (shift_byte % reg_bytes);
+				freq_pct = (shift_byte < reg_bytes) ?
+					   &freq_pct30 : &freq_pct74;
+				*freq_pct |= (svsb->freq_pct[i] << b_sft);
+				shift_byte++;
+			}
+		} else if (svsb->type == SVSB_LOW) {
+			/* freq_pct[turn_pt] ~ freq_pct[opp_count - 1] */
+			for (i = turn_pt; i < svsb->opp_count; i++) {
+				b_sft = bits8 * (shift_byte % reg_bytes);
+				freq_pct = (shift_byte < reg_bytes) ?
+					   &freq_pct30 : &freq_pct74;
+				*freq_pct |= (svsb->freq_pct[i] << b_sft);
+				shift_byte++;
+			}
+		}
+	}
+
+	svs_writel_relaxed(svsp, freq_pct74, FREQPCT74);
+	svs_writel_relaxed(svsp, freq_pct30, FREQPCT30);
+}
+
 static void svs_get_bank_volts_v2(struct svs_platform *svsp)
 {
 	struct svs_bank *svsb = svsp->pbank;
@@ -1247,6 +1491,25 @@ static int svs_init02(struct svs_platform *svsp)
 		}
 	}
 
+	/*
+	 * 2-line high/low bank update its corresponding opp voltages only.
+	 * Therefore, we sync voltages from opp for high/low bank voltages
+	 * consistency.
+	 */
+	for (idx = 0; idx < svsp->bank_max; idx++) {
+		svsb = &svsp->banks[idx];
+
+		if (!(svsb->mode_support & SVSB_MODE_INIT02))
+			continue;
+
+		if (svsb->type == SVSB_HIGH || svsb->type == SVSB_LOW) {
+			if (svs_sync_bank_volts_from_opp(svsb)) {
+				dev_err(svsb->dev, "sync volt fail\n");
+				return -EPERM;
+			}
+		}
+	}
+
 	return 0;
 }
 
@@ -1291,6 +1554,7 @@ static int svs_suspend(struct device *dev)
 	struct svs_platform *svsp = dev_get_drvdata(dev);
 	struct svs_bank *svsb;
 	unsigned long flags;
+	int ret;
 	u32 idx;
 
 	for (idx = 0; idx < svsp->bank_max; idx++) {
@@ -1309,6 +1573,12 @@ static int svs_suspend(struct device *dev)
 		svs_adjust_pm_opp_volts(svsb, true);
 	}
 
+	ret = reset_control_assert(svsp->rst);
+	if (ret) {
+		dev_err(svsp->dev, "cannot assert reset %d\n", ret);
+		return ret;
+	}
+
 	clk_disable_unprepare(svsp->main_clk);
 
 	return 0;
@@ -1327,6 +1597,12 @@ static int svs_resume(struct device *dev)
 		return ret;
 	}
 
+	ret = reset_control_deassert(svsp->rst);
+	if (ret) {
+		dev_err(svsp->dev, "cannot deassert reset %d\n", ret);
+		return ret;
+	}
+
 	for (idx = 0; idx < svsp->bank_max; idx++) {
 		svsb = &svsp->banks[idx];
 		svsb->suspended = false;
@@ -1365,7 +1641,12 @@ static int svs_bank_resource_setup(struct svs_platform *svsp)
 			svsb->name = "SVSB_CCI";
 			break;
 		case SVSB_GPU:
-			svsb->name = "SVSB_GPU";
+			if (svsb->type == SVSB_HIGH)
+				svsb->name = "SVSB_GPU_HIGH";
+			else if (svsb->type == SVSB_LOW)
+				svsb->name = "SVSB_GPU_LOW";
+			else
+				svsb->name = "SVSB_GPU";
 			break;
 		default:
 			dev_err(svsb->dev, "unknown sw_id: %u\n", svsb->sw_id);
@@ -1419,6 +1700,84 @@ static int svs_bank_resource_setup(struct svs_platform *svsp)
 	return 0;
 }
 
+static bool svs_mt8192_efuse_parsing(struct svs_platform *svsp)
+{
+	struct svs_bank *svsb;
+	struct nvmem_cell *cell;
+	u32 idx, i, vmin, golden_temp;
+
+	for (i = 0; i < svsp->efuse_max; i++)
+		if (svsp->efuse[i])
+			dev_info(svsp->dev, "M_HW_RES%d: 0x%08x\n",
+				 i, svsp->efuse[i]);
+
+	if (!svsp->efuse[9]) {
+		dev_notice(svsp->dev, "svs_efuse[9] = 0x0?\n");
+		return false;
+	}
+
+	/* Svs efuse parsing */
+	vmin = (svsp->efuse[19] >> 4) & GENMASK(1, 0);
+
+	for (idx = 0; idx < svsp->bank_max; idx++) {
+		svsb = &svsp->banks[idx];
+
+		if (vmin == 0x1)
+			svsb->vmin = 0x1e;
+
+		if (svsb->type == SVSB_LOW) {
+			svsb->mtdes = svsp->efuse[10] & GENMASK(7, 0);
+			svsb->bdes = (svsp->efuse[10] >> 16) & GENMASK(7, 0);
+			svsb->mdes = (svsp->efuse[10] >> 24) & GENMASK(7, 0);
+			svsb->dcbdet = (svsp->efuse[17]) & GENMASK(7, 0);
+			svsb->dcmdet = (svsp->efuse[17] >> 8) & GENMASK(7, 0);
+		} else if (svsb->type == SVSB_HIGH) {
+			svsb->mtdes = svsp->efuse[9] & GENMASK(7, 0);
+			svsb->bdes = (svsp->efuse[9] >> 16) & GENMASK(7, 0);
+			svsb->mdes = (svsp->efuse[9] >> 24) & GENMASK(7, 0);
+			svsb->dcbdet = (svsp->efuse[17] >> 16) & GENMASK(7, 0);
+			svsb->dcmdet = (svsp->efuse[17] >> 24) & GENMASK(7, 0);
+		}
+
+		svsb->vmax += svsb->dvt_fixed;
+	}
+
+	/* Thermal efuse parsing */
+	cell = nvmem_cell_get(svsp->dev, "t-calibration-data");
+	if (IS_ERR_OR_NULL(cell)) {
+		dev_err(svsp->dev, "no \"t-calibration-data\"? %ld\n",
+			PTR_ERR(cell));
+		return false;
+	}
+
+	svsp->tefuse = nvmem_cell_read(cell, &svsp->tefuse_max);
+	if (IS_ERR(svsp->tefuse)) {
+		dev_err(svsp->dev, "cannot read thermal efuse: %ld\n",
+			PTR_ERR(svsp->tefuse));
+		return false;
+	}
+
+	svsp->tefuse_max /= sizeof(u32);
+	nvmem_cell_put(cell);
+
+	for (i = 0; i < svsp->tefuse_max; i++)
+		if (svsp->tefuse[i] != 0)
+			break;
+
+	if (i == svsp->tefuse_max)
+		golden_temp = 50; /* All thermal efuse data are 0 */
+	else
+		golden_temp = (svsp->tefuse[0] >> 24) & GENMASK(7, 0);
+
+	for (idx = 0; idx < svsp->bank_max; idx++) {
+		svsb = &svsp->banks[idx];
+		svsb->mts = 500;
+		svsb->bts = (((500 * golden_temp + 250460) / 1000) - 25) * 4;
+	}
+
+	return true;
+}
+
 static bool svs_mt8183_efuse_parsing(struct svs_platform *svsp)
 {
 	struct svs_bank *svsb;
@@ -1702,6 +2061,38 @@ static struct device *svs_add_device_link(struct svs_platform *svsp,
 	return dev;
 }
 
+static int svs_mt8192_platform_probe(struct svs_platform *svsp)
+{
+	struct device *dev;
+	struct svs_bank *svsb;
+	u32 idx;
+
+	svsp->rst = devm_reset_control_get_optional(svsp->dev, "svs_rst");
+	if (IS_ERR(svsp->rst)) {
+		dev_err_probe(svsp->dev, PTR_ERR(svsp->rst),
+			      "cannot get svs reset control\n");
+		return PTR_ERR(svsp->rst);
+	}
+
+	dev = svs_add_device_link(svsp, "lvts");
+	if (IS_ERR(dev))
+		return PTR_ERR(dev);
+
+	for (idx = 0; idx < svsp->bank_max; idx++) {
+		svsb = &svsp->banks[idx];
+
+		if (svsb->type == SVSB_HIGH)
+			svsb->opp_dev = svs_add_device_link(svsp, "mali");
+		else if (svsb->type == SVSB_LOW)
+			svsb->opp_dev = svs_get_subsys_device(svsp, "mali");
+
+		if (IS_ERR(svsb->opp_dev))
+			return PTR_ERR(svsb->opp_dev);
+	}
+
+	return 0;
+}
+
 static int svs_mt8183_platform_probe(struct svs_platform *svsp)
 {
 	struct device *dev;
@@ -1742,6 +2133,61 @@ static int svs_mt8183_platform_probe(struct svs_platform *svsp)
 	return 0;
 }
 
+static struct svs_bank svs_mt8192_banks[] = {
+	{
+		.sw_id			= SVSB_GPU,
+		.type			= SVSB_LOW,
+		.set_freq_pct		= svs_set_bank_freq_pct_v3,
+		.get_volts		= svs_get_bank_volts_v3,
+		.volt_flags		= SVSB_REMOVE_DVTFIXED_VOLT,
+		.mode_support		= SVSB_MODE_INIT02,
+		.opp_count		= MAX_OPP_ENTRIES,
+		.freq_base		= 688000000,
+		.turn_freq_base		= 688000000,
+		.volt_step		= 6250,
+		.volt_base		= 400000,
+		.vmax			= 0x60,
+		.vmin			= 0x1a,
+		.age_config		= 0x555555,
+		.dc_config		= 0x1,
+		.dvt_fixed		= 0x1,
+		.vco			= 0x18,
+		.chk_shift		= 0x87,
+		.core_sel		= 0x0fff0100,
+		.int_st			= BIT(0),
+		.ctl0			= 0x00540003,
+	},
+	{
+		.sw_id			= SVSB_GPU,
+		.type			= SVSB_HIGH,
+		.set_freq_pct		= svs_set_bank_freq_pct_v3,
+		.get_volts		= svs_get_bank_volts_v3,
+		.tzone_name		= "gpu1",
+		.volt_flags		= SVSB_REMOVE_DVTFIXED_VOLT |
+					  SVSB_MON_VOLT_IGNORE,
+		.mode_support		= SVSB_MODE_INIT02 | SVSB_MODE_MON,
+		.opp_count		= MAX_OPP_ENTRIES,
+		.freq_base		= 902000000,
+		.turn_freq_base		= 688000000,
+		.volt_step		= 6250,
+		.volt_base		= 400000,
+		.vmax			= 0x60,
+		.vmin			= 0x1a,
+		.age_config		= 0x555555,
+		.dc_config		= 0x1,
+		.dvt_fixed		= 0x6,
+		.vco			= 0x18,
+		.chk_shift		= 0x87,
+		.core_sel		= 0x0fff0101,
+		.int_st			= BIT(1),
+		.ctl0			= 0x00540003,
+		.tzone_htemp		= 85000,
+		.tzone_htemp_voffset	= 0,
+		.tzone_ltemp		= 25000,
+		.tzone_ltemp_voffset	= 7,
+	},
+};
+
 static struct svs_bank svs_mt8183_banks[] = {
 	{
 		.sw_id			= SVSB_CPU_LITTLE,
@@ -1856,6 +2302,16 @@ struct svs_platform_data {
 	int (*probe)(struct svs_platform *svsp);
 };
 
+static const struct svs_platform_data svs_mt8192_platform_data = {
+	.name = "mt8192-svs",
+	.banks = svs_mt8192_banks,
+	.efuse_parsing = svs_mt8192_efuse_parsing,
+	.irqflags = IRQF_TRIGGER_HIGH,
+	.regs = svs_regs_v2,
+	.bank_max = ARRAY_SIZE(svs_mt8192_banks),
+	.probe = svs_mt8192_platform_probe,
+};
+
 static const struct svs_platform_data svs_mt8183_platform_data = {
 	.name = "mt8183-svs",
 	.banks = svs_mt8183_banks,
@@ -1868,6 +2324,9 @@ static const struct svs_platform_data svs_mt8183_platform_data = {
 
 static const struct of_device_id svs_of_match[] = {
 	{
+		.compatible = "mediatek,mt8192-svs",
+		.data = &svs_mt8192_platform_data,
+	}, {
 		.compatible = "mediatek,mt8183-svs",
 		.data = &svs_mt8183_platform_data,
 	}, {
-- 
2.18.0




More information about the Linux-mediatek mailing list