[PATCH v7 4/4] thermal: mediatek: add another get_temp ops for thermal sensors

Daniel Lezcano daniel.lezcano at linaro.org
Sun Dec 4 09:26:07 PST 2022


On 18/11/2022 12:04, Amjad Ouled-Ameur wrote:
> Provide thermal zone to read thermal sensor in the SoC. We can read all the
> thermal sensors value in the SoC by the node /sys/class/thermal/
> 
> In mtk_thermal_bank_temperature, return -EAGAIN instead of -EACCESS
> on the first read of sensor that often are bogus values.
> This can avoid following warning on boot:
> 
>    thermal thermal_zone6: failed to read out thermal zone (-13)
> 
> Signed-off-by: Michael Kao <michael.kao at mediatek.com>
> Signed-off-by: Hsin-Yi Wang <hsinyi at chromium.org>
> Signed-off-by: Amjad Ouled-Ameur <aouledameur at baylibre.com>
> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno at collabora.com>
> ---
>   drivers/thermal/mtk_thermal.c | 99 ++++++++++++++++++++++++++++++++-----------
>   1 file changed, 74 insertions(+), 25 deletions(-)
> 
> diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c
> index 3a5df1440822..b1f4d19edd4f 100644
> --- a/drivers/thermal/mtk_thermal.c
> +++ b/drivers/thermal/mtk_thermal.c
> @@ -259,6 +259,11 @@ enum mtk_thermal_version {
>   
>   struct mtk_thermal;
>   
> +struct mtk_thermal_zone {
> +	struct mtk_thermal *mt;
> +	int id;
> +};
> +
>   struct thermal_bank_cfg {
>   	unsigned int num_sensors;
>   	const int *sensors;
> @@ -307,6 +312,8 @@ struct mtk_thermal {
>   
>   	const struct mtk_thermal_data *conf;
>   	struct mtk_thermal_bank banks[MAX_NUM_ZONES];
> +
> +	int (*raw_to_mcelsius)(struct mtk_thermal *mt, int sensno, s32 raw);
>   };
>   
>   /* MT8183 thermal sensor data */
> @@ -709,6 +716,29 @@ static void mtk_thermal_put_bank(struct mtk_thermal_bank *bank)
>   		mutex_unlock(&mt->lock);
>   }
>   
> +static int _get_sensor_temp(struct mtk_thermal *mt, int id)
> +{
> +	u32 raw;
> +	int temp;
> +
> +	const struct mtk_thermal_data *conf = mt->conf;
> +
> +	raw = readl(mt->thermal_base + conf->msr[id]);
> +
> +	temp = mt->raw_to_mcelsius(mt, id, raw);
> +
> +	/*
> +	 * The first read of a sensor often contains very high bogus
> +	 * temperature value. Filter these out so that the system does
> +	 * not immediately shut down.
> +	 */
> +
> +	if (temp > 200000)
> +		return -EAGAIN;
> +	else
> +		return temp;
> +}
> +
>   /**
>    * mtk_thermal_bank_temperature - get the temperature of a bank
>    * @bank:	The bank
> @@ -721,26 +751,9 @@ static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
>   	struct mtk_thermal *mt = bank->mt;
>   	const struct mtk_thermal_data *conf = mt->conf;
>   	int i, temp = INT_MIN, max = INT_MIN;
> -	u32 raw;
>   
>   	for (i = 0; i < conf->bank_data[bank->id].num_sensors; i++) {
> -		raw = readl(mt->thermal_base + conf->msr[i]);
> -
> -		if (mt->conf->version == MTK_THERMAL_V1) {
> -			temp = raw_to_mcelsius_v1(
> -				mt, conf->bank_data[bank->id].sensors[i], raw);
> -		} else {
> -			temp = raw_to_mcelsius_v2(
> -				mt, conf->bank_data[bank->id].sensors[i], raw);
> -		}
> -
> -		/*
> -		 * The first read of a sensor often contains very high bogus
> -		 * temperature value. Filter these out so that the system does
> -		 * not immediately shut down.
> -		 */
> -		if (temp > 200000)
> -			temp = 0;
> +		temp = _get_sensor_temp(mt, i);
>   
>   		if (temp > max)
>   			max = temp;
> @@ -749,9 +762,10 @@ static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
>   	return max;
>   }
>   
> -static int mtk_read_temp(struct thermal_zone_device *tz, int *temperature)
> +static int mtk_read_temp(struct thermal_zone_device *tzdev, int *temperature)
>   {
> -	struct mtk_thermal *mt = tz->devdata;
> +	struct mtk_thermal_zone *tz = tzdev->devdata;
> +	struct mtk_thermal *mt = tz->mt;
>   	int i;
>   	int tempmax = INT_MIN;
>   
> @@ -770,10 +784,28 @@ static int mtk_read_temp(struct thermal_zone_device *tz, int *temperature)
>   	return 0;
>   }
>   
> +static int mtk_read_sensor_temp(struct thermal_zone_device *tzdev, int *temperature)
> +{
> +	struct mtk_thermal_zone *tz = tzdev->devdata;
> +	struct mtk_thermal *mt = tz->mt;
> +	int id = tz->id - 1;
> +
> +	if (id < 0)
> +		return -EACCES;
> +
> +	*temperature = _get_sensor_temp(mt, id);
> +
> +	return 0;
> +}
> +
>   static const struct thermal_zone_device_ops mtk_thermal_ops = {
>   	.get_temp = mtk_read_temp,
>   };
>   
> +static const struct thermal_zone_device_ops mtk_thermal_sensor_ops = {
> +	.get_temp = mtk_read_sensor_temp,
> +};
> +
>   static void mtk_thermal_init_bank(struct mtk_thermal *mt, int num,
>   				  u32 apmixed_phys_base, u32 auxadc_phys_base,
>   				  int ctrl_id)
> @@ -1072,6 +1104,7 @@ static int mtk_thermal_probe(struct platform_device *pdev)
>   	u64 auxadc_phys_base, apmixed_phys_base;
>   	struct thermal_zone_device *tzdev;
>   	void __iomem *apmixed_base, *auxadc_base;
> +	struct mtk_thermal_zone *tz;
>   
>   	mt = devm_kzalloc(&pdev->dev, sizeof(*mt), GFP_KERNEL);
>   	if (!mt)
> @@ -1150,6 +1183,9 @@ static int mtk_thermal_probe(struct platform_device *pdev)
>   
>   	mtk_thermal_turn_on_buffer(mt, apmixed_base);
>   
> +	mt->raw_to_mcelsius = (mt->conf->version == MTK_THERMAL_V1) ?
> +				raw_to_mcelsius_v1 : raw_to_mcelsius_v2;
> +
>   	if (mt->conf->version == MTK_THERMAL_V2) {
>   		mtk_thermal_release_periodic_ts(mt, auxadc_base);
>   	}
> @@ -1161,11 +1197,24 @@ static int mtk_thermal_probe(struct platform_device *pdev)
>   
>   	platform_set_drvdata(pdev, mt);
>   
> -	tzdev = devm_thermal_of_zone_register(&pdev->dev, 0, mt,
> -					      &mtk_thermal_ops);
> -	if (IS_ERR(tzdev)) {
> -		ret = PTR_ERR(tzdev);
> -		goto err_disable_clk_peri_therm;
> +	for (i = 0; i < mt->conf->num_sensors + 1; i++) {
> +		tz = devm_kmalloc(&pdev->dev, sizeof(*tz), GFP_KERNEL);
> +		if (!tz)
> +			return -ENOMEM;
> +
> +		tz->mt = mt;
> +		tz->id = i;
> +
> +		tzdev = devm_thermal_of_zone_register(&pdev->dev, i, tz, (i == 0) ?
> +							     &mtk_thermal_ops :
> +							     &mtk_thermal_sensor_ops);

Here you use again the aggregation

> +
> +		if (IS_ERR(tzdev)) {
> +			ret = PTR_ERR(tzdev);
> +			if (ret == -ENODEV)
> +				continue;
> +			goto err_disable_clk_peri_therm;
> +		}
>   	}
>   
>   	ret = devm_thermal_add_hwmon_sysfs(tzdev);
> 

-- 
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog




More information about the Linux-mediatek mailing list