[PATCH v12 1/1] arm64: dts: Add MediaTek MT8186 dts and evaluation board and Makefile

[allen-kh.cheng]

HI Nícolas,

Thanks for your reminder.

On Mon, 2022-08-01 at 18:01 -0400, Nícolas F. R. A. Prado wrote:
> Hi Allen,
> 
> On Mon, Aug 01, 2022 at 08:39:52PM +0800, Allen-KH Cheng wrote:
> > Add basic chip support for MediaTek MT8186.
> > 
> > Signed-off-by: Allen-KH Cheng <Allen-KH.Cheng at mediatek.com>
> > ---
> >  arch/arm64/boot/dts/mediatek/Makefile       |   1 +
> >  arch/arm64/boot/dts/mediatek/mt8186-evb.dts | 238 ++++++
> >  arch/arm64/boot/dts/mediatek/mt8186.dtsi    | 874
> > ++++++++++++++++++++
> >  3 files changed, 1113 insertions(+)
> >  create mode 100644 arch/arm64/boot/dts/mediatek/mt8186-evb.dts
> >  create mode 100644 arch/arm64/boot/dts/mediatek/mt8186.dtsi
> > 
> 
> [..]
> > diff --git a/arch/arm64/boot/dts/mediatek/mt8186-evb.dts
> > b/arch/arm64/boot/dts/mediatek/mt8186-evb.dts
> > new file mode 100644
> > index 000000000000..7d4a64ab95e4
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt8186-evb.dts
> 
> [..]
> > +&pio {
> > +	i2c0_pins: i2c0-default-pins {
> > +		pins-bus {
> > +			pinmux = <PINMUX_GPIO128__FUNC_SDA0>,
> > +				 <PINMUX_GPIO127__FUNC_SCL0>;
> > +			bias-disable;
> > +			drive-strength-microamp = <1000>;
> > +			drive-strength = <4>;
> 
> You can't use both drive-strength-microamp and drive-strength. You
> only want the
> microamp one here (and for the others below), since these are i2c
> pins.
> 

I will remove drive-strength for i2c pins.

> > +			input-enable;
> > +		};
> > +	};
> 
> [..]
> > diff --git a/arch/arm64/boot/dts/mediatek/mt8186.dtsi
> > b/arch/arm64/boot/dts/mediatek/mt8186.dtsi
> > new file mode 100644
> > index 000000000000..38f9466eea42
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt8186.dtsi
> > @@ -0,0 +1,874 @@
> 
> [..]
> > +		pio: pinctrl at 10005000 {
> > +			compatible = "mediatek,mt8186-pinctrl";
> > +			reg = <0 0x10005000 0 0x1000>,
> > +			      <0 0x10002000 0 0x0200>,
> > +			      <0 0x10002200 0 0x0200>,
> > +			      <0 0x10002400 0 0x0200>,
> > +			      <0 0x10002600 0 0x0200>,
> > +			      <0 0x10002A00 0 0x0200>,
> > +			      <0 0x10002C00 0 0x0200>,
> > +			      <0 0x1000B000 0 0x1000>;
> 
> Please use lowercase hex for addresses.
> 

ok.

> > +			reg-names = "iocfg0", "iocfg_bm", "iocfg_bl",
> > "iocfg_br",
> > +				    "iocfg_lm", "iocfg_rb", "iocfg_tl",
> > "eint";
> > +			gpio-controller;
> > +			#gpio-cells = <2>;
> > +			gpio-ranges = <&pio 0 0 185>;
> > +			interrupt-controller;
> > +			interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH
> > 0>;
> > +			#interrupt-cells = <2>;
> > +		};
> 
> [..]
> > +		xhci0: usb at 11200000 {
> > +			compatible = "mediatek,mt8186-xhci",
> > +				     "mediatek,mtk-xhci";
> > +			reg = <0 0x11200000 0 0x1000>,
> > +			      <0 0x11203e00 0 0x0100>;
> > +			reg-names = "mac", "ippc";
> > +			interrupts = <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH
> > 0>;
> > +			phys = <&u2port0 PHY_TYPE_USB2>;
> > +			clocks = <&topckgen CLK_TOP_USB_TOP>,
> > +				 <&infracfg_ao
> > CLK_INFRA_AO_SSUSB_TOP_XHCI>,
> > +				 <&infracfg_ao
> > CLK_INFRA_AO_SSUSB_TOP_HCLK>,
> > +				 <&infracfg_ao CLK_INFRA_AO_ICUSB>,
> > +				 <&infracfg_ao
> > CLK_INFRA_AO_SSUSB_TOP_REF>;
> > +			clock-names = "sys_ck", "ref_ck", "mcu_ck",
> > "dma_ck", "xhci_ck";
> 
> The clocks and clock-names don't match, can you confirm whether
> they're right?
> (But keep this clock order, see the comment on xhci1 below)
> 

The clocks of ref_ck and xhci_ck are not correct. I will update in next
version.

> > +			mediatek,syscon-wakeup = <&pericfg 0x420 2>;
> > +			wakeup-source;
> > +			status = "disabled";
> > +		};
> 
> [..]
> > +		xhci1: usb at 11280000 {
> > +			compatible = "mediatek,mt8186-xhci",
> > +				     "mediatek,mtk-xhci";
> > +			reg = <0 0x11280000 0 0x1000>,
> > +			      <0 0x11283e00 0 0x0100>;
> > +			reg-names = "mac", "ippc";
> > +			interrupts = <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH
> > 0>;
> > +			phys = <&u2port1 PHY_TYPE_USB2>,
> > +			       <&u3port1 PHY_TYPE_USB3>;
> > +			clocks = <&infracfg_ao
> > CLK_INFRA_AO_SSUSB_TOP_P1_SYS>,
> > +				 <&infracfg_ao
> > CLK_INFRA_AO_SSUSB_TOP_P1_XHCI>,
> > +				 <&infracfg_ao
> > CLK_INFRA_AO_SSUSB_TOP_P1_HCLK>,
> > +				 <&infracfg_ao
> > CLK_INFRA_AO_SSUSB_TOP_P1_REF>;
> > +			clock-names = "sys_ck", "ref_ck", "mcu_ck",
> > "xhci_ck";
> 
> The xhci dt-binding enforces this clock order:
> 
> 	sys_ck, ref_ck, mcu_ck, dma_ck, xhci_ck
> 
> You can't skip dma_ck, otherwise you'll see a dtbs_check warning. So
> if this
> hardware block has a fixed clock connected to the dma_ck slot (ie it
> isn't
> controllable), then just add a fixed clock entry for it (eg
> <&clk26m>).
> 
> The clock names also look switched here, please double-check.
> 
> Thanks,
> Nícolas
> 

The hw does not control this. I will add fixed clock for dma_ck.

Thanks,
Allen


> > +			mediatek,syscon-wakeup = <&pericfg 0x424 2>;
> > +			wakeup-source;
> > +			status = "disabled";
> > +		};