[PATCH v24 5/7] soc: mediatek: SVS: add debug commands
Roger Lu
roger.lu at mediatek.com
Wed Apr 20 03:20:42 PDT 2022
The purpose of SVS is to help find the suitable voltages
for DVFS. Therefore, if SVS bank voltages are concerned
to be wrong, we can show/disable SVS bank voltages by
this patch.
Signed-off-by: Roger Lu <roger.lu at mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno at collabora.com>
---
drivers/soc/mediatek/mtk-svs.c | 275 +++++++++++++++++++++++++++++++++
1 file changed, 275 insertions(+)
diff --git a/drivers/soc/mediatek/mtk-svs.c b/drivers/soc/mediatek/mtk-svs.c
index 39dd21630885..4ae9036c98ff 100644
--- a/drivers/soc/mediatek/mtk-svs.c
+++ b/drivers/soc/mediatek/mtk-svs.c
@@ -7,6 +7,7 @@
#include <linux/clk.h>
#include <linux/completion.h>
#include <linux/cpuidle.h>
+#include <linux/debugfs.h>
#include <linux/device.h>
#include <linux/init.h>
#include <linux/interrupt.h>
@@ -23,6 +24,7 @@
#include <linux/pm_opp.h>
#include <linux/pm_runtime.h>
#include <linux/regulator/consumer.h>
+#include <linux/seq_file.h>
#include <linux/slab.h>
#include <linux/spinlock.h>
#include <linux/thermal.h>
@@ -69,6 +71,39 @@
static DEFINE_SPINLOCK(svs_lock);
+#define debug_fops_ro(name) \
+ static int svs_##name##_debug_open(struct inode *inode, \
+ struct file *filp) \
+ { \
+ return single_open(filp, svs_##name##_debug_show, \
+ inode->i_private); \
+ } \
+ static const struct file_operations svs_##name##_debug_fops = { \
+ .owner = THIS_MODULE, \
+ .open = svs_##name##_debug_open, \
+ .read = seq_read, \
+ .llseek = seq_lseek, \
+ .release = single_release, \
+ }
+
+#define debug_fops_rw(name) \
+ static int svs_##name##_debug_open(struct inode *inode, \
+ struct file *filp) \
+ { \
+ return single_open(filp, svs_##name##_debug_show, \
+ inode->i_private); \
+ } \
+ static const struct file_operations svs_##name##_debug_fops = { \
+ .owner = THIS_MODULE, \
+ .open = svs_##name##_debug_open, \
+ .read = seq_read, \
+ .write = svs_##name##_debug_write, \
+ .llseek = seq_lseek, \
+ .release = single_release, \
+ }
+
+#define svs_dentry_data(name) {__stringify(name), &svs_##name##_debug_fops}
+
/**
* enum svsb_phase - svs bank phase enumeration
* @SVSB_PHASE_ERROR: svs bank encounters unexpected condition
@@ -269,6 +304,7 @@ struct svs_platform_data {
* @tzone_name: thermal zone name
* @phase: bank current phase
* @volt_od: bank voltage overdrive
+ * @reg_data: bank register data in different phase for debug purpose
* @pm_runtime_enabled_count: bank pm runtime enabled count
* @mode_support: bank mode support.
* @freq_base: reference frequency for bank init
@@ -328,6 +364,7 @@ struct svs_bank {
char *tzone_name;
enum svsb_phase phase;
s32 volt_od;
+ u32 reg_data[SVSB_PHASE_MAX][SVS_REG_MAX];
u32 pm_runtime_enabled_count;
u32 mode_support;
u32 freq_base;
@@ -469,6 +506,220 @@ static int svs_adjust_pm_opp_volts(struct svs_bank *svsb)
return ret;
}
+static int svs_dump_debug_show(struct seq_file *m, void *p)
+{
+ struct svs_platform *svsp = (struct svs_platform *)m->private;
+ struct svs_bank *svsb;
+ unsigned long svs_reg_addr;
+ u32 idx, i, j, bank_id;
+
+ for (i = 0; i < svsp->efuse_max; i++)
+ if (svsp->efuse && svsp->efuse[i])
+ seq_printf(m, "M_HW_RES%d = 0x%08x\n",
+ i, svsp->efuse[i]);
+
+ for (i = 0; i < svsp->tefuse_max; i++)
+ if (svsp->tefuse)
+ seq_printf(m, "THERMAL_EFUSE%d = 0x%08x\n",
+ i, svsp->tefuse[i]);
+
+ for (bank_id = 0, idx = 0; idx < svsp->bank_max; idx++, bank_id++) {
+ svsb = &svsp->banks[idx];
+
+ for (i = SVSB_PHASE_INIT01; i <= SVSB_PHASE_MON; i++) {
+ seq_printf(m, "Bank_number = %u\n", bank_id);
+
+ if (i == SVSB_PHASE_INIT01 || i == SVSB_PHASE_INIT02)
+ seq_printf(m, "mode = init%d\n", i);
+ else if (i == SVSB_PHASE_MON)
+ seq_puts(m, "mode = mon\n");
+ else
+ seq_puts(m, "mode = error\n");
+
+ for (j = DESCHAR; j < SVS_REG_MAX; j++) {
+ svs_reg_addr = (unsigned long)(svsp->base +
+ svsp->regs[j]);
+ seq_printf(m, "0x%08lx = 0x%08x\n",
+ svs_reg_addr, svsb->reg_data[i][j]);
+ }
+ }
+ }
+
+ return 0;
+}
+
+debug_fops_ro(dump);
+
+static int svs_enable_debug_show(struct seq_file *m, void *v)
+{
+ struct svs_bank *svsb = (struct svs_bank *)m->private;
+
+ switch (svsb->phase) {
+ case SVSB_PHASE_ERROR:
+ seq_puts(m, "disabled\n");
+ break;
+ case SVSB_PHASE_INIT01:
+ seq_puts(m, "init1\n");
+ break;
+ case SVSB_PHASE_INIT02:
+ seq_puts(m, "init2\n");
+ break;
+ case SVSB_PHASE_MON:
+ seq_puts(m, "mon mode\n");
+ break;
+ default:
+ seq_puts(m, "unknown\n");
+ break;
+ }
+
+ return 0;
+}
+
+static ssize_t svs_enable_debug_write(struct file *filp,
+ const char __user *buffer,
+ size_t count, loff_t *pos)
+{
+ struct svs_bank *svsb = file_inode(filp)->i_private;
+ struct svs_platform *svsp = dev_get_drvdata(svsb->dev);
+ unsigned long flags;
+ int enabled, ret;
+ char *buf = NULL;
+
+ if (count >= PAGE_SIZE)
+ return -EINVAL;
+
+ buf = (char *)memdup_user_nul(buffer, count);
+ if (IS_ERR(buf))
+ return PTR_ERR(buf);
+
+ ret = kstrtoint(buf, 10, &enabled);
+ if (ret)
+ return ret;
+
+ if (!enabled) {
+ spin_lock_irqsave(&svs_lock, flags);
+ svsp->pbank = svsb;
+ svsb->mode_support = SVSB_MODE_ALL_DISABLE;
+ svs_switch_bank(svsp);
+ svs_writel_relaxed(svsp, SVSB_EN_OFF, SVSEN);
+ svs_writel_relaxed(svsp, SVSB_INTSTS_CLEAN, INTSTS);
+ spin_unlock_irqrestore(&svs_lock, flags);
+
+ svsb->phase = SVSB_PHASE_ERROR;
+ svs_adjust_pm_opp_volts(svsb);
+ }
+
+ kfree(buf);
+
+ return count;
+}
+
+debug_fops_rw(enable);
+
+static int svs_status_debug_show(struct seq_file *m, void *v)
+{
+ struct svs_bank *svsb = (struct svs_bank *)m->private;
+ struct dev_pm_opp *opp;
+ int tzone_temp = 0, ret;
+ u32 i;
+
+ ret = thermal_zone_get_temp(svsb->tzd, &tzone_temp);
+ if (ret)
+ seq_printf(m, "%s: temperature ignore\n", svsb->name);
+ else
+ seq_printf(m, "%s: temperature = %d\n", svsb->name, tzone_temp);
+
+ for (i = 0; i < svsb->opp_count; i++) {
+ opp = dev_pm_opp_find_freq_exact(svsb->opp_dev,
+ svsb->opp_dfreq[i], true);
+ if (IS_ERR(opp)) {
+ seq_printf(m, "%s: cannot find freq = %u (%ld)\n",
+ svsb->name, svsb->opp_dfreq[i],
+ PTR_ERR(opp));
+ return PTR_ERR(opp);
+ }
+
+ seq_printf(m, "opp_freq[%02u]: %u, opp_volt[%02u]: %lu, ",
+ i, svsb->opp_dfreq[i], i,
+ dev_pm_opp_get_voltage(opp));
+ seq_printf(m, "svsb_volt[%02u]: 0x%x, freq_pct[%02u]: %u\n",
+ i, svsb->volt[i], i, svsb->freq_pct[i]);
+ dev_pm_opp_put(opp);
+ }
+
+ return 0;
+}
+
+debug_fops_ro(status);
+
+static int svs_create_debug_cmds(struct svs_platform *svsp)
+{
+ struct svs_bank *svsb;
+ struct dentry *svs_dir, *svsb_dir, *file_entry;
+ const char *d = "/sys/kernel/debug/svs";
+ u32 i, idx;
+
+ struct svs_dentry {
+ const char *name;
+ const struct file_operations *fops;
+ };
+
+ struct svs_dentry svs_entries[] = {
+ svs_dentry_data(dump),
+ };
+
+ struct svs_dentry svsb_entries[] = {
+ svs_dentry_data(enable),
+ svs_dentry_data(status),
+ };
+
+ svs_dir = debugfs_create_dir("svs", NULL);
+ if (IS_ERR(svs_dir)) {
+ dev_err(svsp->dev, "cannot create %s: %ld\n",
+ d, PTR_ERR(svs_dir));
+ return PTR_ERR(svs_dir);
+ }
+
+ for (i = 0; i < ARRAY_SIZE(svs_entries); i++) {
+ file_entry = debugfs_create_file(svs_entries[i].name, 0664,
+ svs_dir, svsp,
+ svs_entries[i].fops);
+ if (IS_ERR(file_entry)) {
+ dev_err(svsp->dev, "cannot create %s/%s: %ld\n",
+ d, svs_entries[i].name, PTR_ERR(file_entry));
+ return PTR_ERR(file_entry);
+ }
+ }
+
+ for (idx = 0; idx < svsp->bank_max; idx++) {
+ svsb = &svsp->banks[idx];
+
+ if (svsb->mode_support == SVSB_MODE_ALL_DISABLE)
+ continue;
+
+ svsb_dir = debugfs_create_dir(svsb->name, svs_dir);
+ if (IS_ERR(svsb_dir)) {
+ dev_err(svsp->dev, "cannot create %s/%s: %ld\n",
+ d, svsb->name, PTR_ERR(svsb_dir));
+ return PTR_ERR(svsb_dir);
+ }
+
+ for (i = 0; i < ARRAY_SIZE(svsb_entries); i++) {
+ file_entry = debugfs_create_file(svsb_entries[i].name,
+ 0664, svsb_dir, svsb,
+ svsb_entries[i].fops);
+ if (IS_ERR(file_entry)) {
+ dev_err(svsp->dev, "no %s/%s/%s?: %ld\n",
+ d, svsb->name, svsb_entries[i].name,
+ PTR_ERR(file_entry));
+ return PTR_ERR(file_entry);
+ }
+ }
+ }
+
+ return 0;
+}
+
static u32 interpolate(u32 f0, u32 f1, u32 v0, u32 v1, u32 fx)
{
u32 vx;
@@ -593,6 +844,16 @@ static void svs_set_bank_phase(struct svs_platform *svsp,
}
}
+static inline void svs_save_bank_register_data(struct svs_platform *svsp,
+ enum svsb_phase phase)
+{
+ struct svs_bank *svsb = svsp->pbank;
+ enum svs_reg_index rg_i;
+
+ for (rg_i = DESCHAR; rg_i < SVS_REG_MAX; rg_i++)
+ svsb->reg_data[phase][rg_i] = svs_readl_relaxed(svsp, rg_i);
+}
+
static inline void svs_error_isr_handler(struct svs_platform *svsp)
{
struct svs_bank *svsb = svsp->pbank;
@@ -607,6 +868,8 @@ static inline void svs_error_isr_handler(struct svs_platform *svsp)
svs_readl_relaxed(svsp, SMSTATE1));
dev_err(svsb->dev, "TEMP = 0x%08x\n", svs_readl_relaxed(svsp, TEMP));
+ svs_save_bank_register_data(svsp, SVSB_PHASE_ERROR);
+
svsb->phase = SVSB_PHASE_ERROR;
svs_writel_relaxed(svsp, SVSB_EN_OFF, SVSEN);
svs_writel_relaxed(svsp, SVSB_INTSTS_CLEAN, INTSTS);
@@ -621,6 +884,8 @@ static inline void svs_init01_isr_handler(struct svs_platform *svsp)
svs_readl_relaxed(svsp, VDESIGN30),
svs_readl_relaxed(svsp, DCVALUES));
+ svs_save_bank_register_data(svsp, SVSB_PHASE_INIT01);
+
svsb->phase = SVSB_PHASE_INIT01;
svsb->dc_voffset_in = ~(svs_readl_relaxed(svsp, DCVALUES) &
GENMASK(15, 0)) + 1;
@@ -646,6 +911,8 @@ static inline void svs_init02_isr_handler(struct svs_platform *svsp)
svs_readl_relaxed(svsp, VOP30),
svs_readl_relaxed(svsp, DCVALUES));
+ svs_save_bank_register_data(svsp, SVSB_PHASE_INIT02);
+
svsb->phase = SVSB_PHASE_INIT02;
svsb->get_volts(svsp);
@@ -657,6 +924,8 @@ static inline void svs_mon_mode_isr_handler(struct svs_platform *svsp)
{
struct svs_bank *svsb = svsp->pbank;
+ svs_save_bank_register_data(svsp, SVSB_PHASE_MON);
+
svsb->phase = SVSB_PHASE_MON;
svsb->get_volts(svsp);
@@ -1631,6 +1900,12 @@ static int svs_probe(struct platform_device *pdev)
goto svs_probe_iounmap;
}
+ ret = svs_create_debug_cmds(svsp);
+ if (ret) {
+ dev_err(svsp->dev, "svs create debug cmds fail: %d\n", ret);
+ goto svs_probe_iounmap;
+ }
+
return 0;
svs_probe_iounmap:
--
2.18.0
More information about the Linux-mediatek
mailing list