[PATCH v3 2/2] mmc: mediatek: Add HS400 online tuning support

[Ulf Hansson]

On Thu, 16 Sept 2021 at 11:47, Wenbin Mei <wenbin.mei at mediatek.com> wrote:
>
> On Tue, 2021-09-14 at 10:46 +0200, Ulf Hansson wrote:
> > On Wed, 8 Sept 2021 at 03:32, Wenbin Mei <wenbin.mei at mediatek.com>
> > wrote:
> > >
> > > Due to the influence of the corner IC and vcore voltage, for the
> > > stability
> > > of HS400 mode, we Add HS400 mode online tuning support for mediatek
> > > mmc
> > > host.
> >
> > My apologies, but I am not familiar with what 'HS400 online tuning'
> > is? Can you please elaborate on this?
> >
> > Is it specific for a Mediatek eMMC controller - or is a common eMMC
> > feature that is described in the eMMC spec?
> >
> According to JEDEC Spec, there is no need to do tuning under HS400 mode
> since the Rx signal is aligned with the DS signal. However, MediaTek's
> IC need set its "DS delay" internally to ensure it can latch Rx signal
> correctly.
> In previous version, We provide an "hs400-ds-delay" in device tree to
> cover different chipset/PCB design, and it works fine in most cases.
> But, with the development of process technology and the big VCore
> voltage scale range(may have 0.7V/0.6V/0.55V), it is difficult to find
> a suitable "hs400-ds-delay" to cover all of IC corner
> cases(SSSS/TTTT/FFFF).
> So that We must have the ability to do hs400 online tuning.
> It is specific for the Mediatek eMMC controller which support HS400
> mode.

I see, thanks for clarifying. Please put some of this information in
the commit message for the next version, it certainly helps to
understand.

[...]

> > > +static int msdc_send_cxd_data(struct mmc_card *card, struct
> > > mmc_host *host)
> > > +{
> > > +       struct mmc_request mrq = {};
> > > +       struct mmc_command cmd = {};
> > > +       struct mmc_data data = {};
> > > +       unsigned int len = 512;
> > > +       struct scatterlist sg;
> > > +       u8 *ext_csd;
> > > +
> > > +       ext_csd = kzalloc(len, GFP_KERNEL);
> > > +       if (!ext_csd)
> > > +               return -ENOMEM;
> > > +
> > > +       mrq.cmd = &cmd;
> > > +       mrq.data = &data;
> > > +
> > > +       cmd.opcode = MMC_SEND_EXT_CSD;
> > > +       cmd.arg = 0;
> > > +       cmd.flags = MMC_RSP_SPI_R1 | MMC_RSP_R1 | MMC_CMD_ADTC;
> > > +
> > > +       data.blksz = len;
> > > +       data.blocks = 1;
> > > +       data.flags = MMC_DATA_READ;
> > > +       data.sg = &sg;
> > > +       data.sg_len = 1;
> > > +
> > > +       sg_init_one(&sg, ext_csd, len);
> > > +       mmc_set_data_timeout(&data, card);
> > > +       mmc_wait_for_req(host, &mrq);
> > > +
> > > +       kfree(ext_csd);
> > > +
> > > +       if (cmd.error)
> > > +               return cmd.error;
> > > +       if (data.error)
> > > +               return data.error;
> > > +
> > > +       return 0;
> >
> > Why do we need to send a MMC_SEND_EXT_CSD command, exactly?
> >
> > Why can't mmc_send_tuning() work here too? What does the eMMC spec
> > state about this?
> >
> The CMD21 is illegal under hs400 mode so that cannot use the
> mmc_send_tuning(). The CMD8 is suitable because it will receive 1 block
> of non-zero data.

I see.

In that case it seems better to use mmc_get_ext_csd(), from the core,
rather than open coding the above. To do that, you also need to move
the declaration of mmc_get_ext_csd() to include/linux/mmc/host.h.

[...]

Kind regards
Uffe