[v6,5/9] dt-bindings: pinctrl: update bindings for MT7986 SoC
Rob Herring
robh at kernel.org
Mon Oct 11 18:26:39 PDT 2021
On Mon, Oct 04, 2021 at 05:41:40PM +0800, Sam Shih wrote:
> This updates bindings for MT7986 pinctrl driver. The
> difference of pinctrl between mt7986a and mt7986b is that pin-41 to pin-65
> do not exist on mt7986b
>
> Signed-off-by: Sam Shih <sam.shih at mediatek.com>
>
> ---
> v6 : fixed yamllint warnings/errors v2
> v5 : fixed yamllint warnings/errors v1
> v4 : used yaml format instead of txt format document
> v3 : make mt7986 pinctrl bindings as a separate file
> v2 : deleted the redundant description of mt7986a/mt7986b
> ---
> .../pinctrl/mediatek,mt7986-pinctrl.yaml | 361 ++++++++++++++++++
> 1 file changed, 361 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml
> new file mode 100644
> index 000000000000..cde842d093dc
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt7986-pinctrl.yaml
> @@ -0,0 +1,361 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/mediatek,mt7986-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Mediatek MT7986 Pin Controller Device Tree Bindings
> +
> +maintainers:
> + - Sean Wang <sean.wang at kernel.org>
> +
> +description: |+
> + The MediaTek's MT7986 Pin controller is used to control SoC pins.
> +
> +properties:
> + compatible:
> + enum:
> + - mediatek,mt7986a-pinctrl
> + - mediatek,mt7986b-pinctrl
> +
> + reg:
> + minItems: 8
> + maxItems: 8
> +
> + reg-names:
> + items:
> + - const: gpio_base
> + - const: iocfg_rt_base
> + - const: iocfg_rb_base
> + - const: iocfg_lt_base
> + - const: iocfg_lb_base
> + - const: iocfg_tr_base
> + - const: iocfg_tl_base
_base is redundant. Drop.
> + - const: eint
> +
> + gpio-controller: true
> +
> + "#gpio-cells":
> + const: 2
> + description: |
> + Number of cells in GPIO specifier. Since the generic GPIO
> + binding is used, the amount of cells must be specified as 2. See the below
> + mentioned gpio binding representation for description of particular cells.
> +
> + gpio-ranges:
> + minItems: 1
> + maxItems: 5
> + description: |
> + GPIO valid number range.
> +
> + interrupt-controller: true
> +
> + interrupts:
> + maxItems: 1
> +
> + "#interrupt-cells":
> + const: 2
> +
> +required:
> + - compatible
> + - reg
> + - reg-names
> + - gpio-controller
> + - "#gpio-cells"
> +
> +patternProperties:
> + '-[0-9]+$':
This could be a bit more specific. Most new bindings use '-pins$' here.
> + type: object
> + additionalProperties: false
> +
> + patternProperties:
> + 'mux':
Do you really mean '.*mux.*' because that's what is allowed here. If the
node name is really just 'mux', then this isn't a pattern and should be
under 'properties'.
> + type: object
> + additionalProperties: false
> + description: |
> + pinmux configuration nodes.
> +
> + Valid value function pins (in pin#)
> + ---------------------------------------------------------------------
> + "watchdog" "watchdog" 0
> + "wifi_led" "led" 1, 2
> + "i2c" "i2c" 3, 4
> + "uart1_0" "uart" 7, 8, 9, 10
> + "pcie_clk" "pcie" 9
> + "pcie_wake" "pcie" 10
> + "spi1_0" "spi" 11, 12, 13, 14
> + "pwm1_1" "pwm" 20,
> + "pwm0" "pwm" 21,
> + "pwm1_0" "pwm" 22,
> + "snfi" "flash" 23, 24, 25, 26, 27, 28
> + "spi1_2" "spi" 29, 30, 31, 32
> + "emmc_45" "emmc" 22, 23, 24, 25, 26, 27, 28, 29, 30,
> + 31, 32
> + "spi1_1" "spi" 23, 24, 25, 26
> + "uart1_2" "uart" 29, 30, 31, 32
> + "uart1_1" "uart" 23, 24, 25, 26
> + "uart2_0" "uart" 29, 30, 31, 32
> + "spi0" "spi" 33, 34, 35, 36
> + "spi0_wp_hold" "spi" 37, 38
> + "uart1_3_rx_tx" "uart" 35, 36
> + "uart1_3_cts_rts" "uart" 37, 38
> + "uart2_1" "uart" 33, 34, 35, 36
> + "spi1_3" "spi" 33, 34, 35, 36
> + "uart0" "uart" 39, 40
> + "pcie_pereset" "pcie" 41
> + "uart1" "uart" 42, 43, 44, 45
> + "uart2" "uart" 46, 47, 48, 49
> + "emmc_51" "emmc" 50, 51, 52, 53, 54, 55, 56, 57, 57,
> + 59, 60, 61
> + "pcm" "audio" 62, 63, 64, 65
> + "i2s" "audio" 62, 63, 64, 65
> + "switch_int" "eth" 66
> + "mdc_mdio" "eth" 67
> +
> + $ref: "/schemas/pinctrl/pinmux-node.yaml"
> + properties:
> + function:
> + description: |
> + A string containing the name of the function to mux to the group.
> + There is no "audio", "pcie" functions on mt7986b, you can only use
> + those functions on mt7986a.
> + enum: [audio, emmc, eth, i2c, led, flash, pcie, pwm, spi, uart,
> + watchdog, wifi]
> + groups:
> + description: |
> + An array of strings. Each string contains the name of a group.
> + There is no "pcie_pereset", "uart1", "uart2" "emmc_51", "pcm",
> + and "i2s" groups on mt7986b, you can only use those groups on
> + mt7986a.
> + required:
> + - function
> + - groups
> +
> + allOf:
> + - if:
> + properties:
> + function:
> + const: audio
> + then:
> + properties:
> + groups:
> + enum: [pcm, i2s]
> + - if:
> + properties:
> + function:
> + const: emmc
> + then:
> + properties:
> + groups:
> + enum: [emmc, emmc_rst]
> + - if:
> + properties:
> + function:
> + const: eth
> + then:
> + properties:
> + groups:
> + enum: [switch_int, mdc_mdio]
> + - if:
> + properties:
> + function:
> + const: i2c
> + then:
> + properties:
> + groups:
> + enum: [i2c]
> + - if:
> + properties:
> + function:
> + const: led
> + then:
> + properties:
> + groups:
> + enum: [wifi_led]
> + - if:
> + properties:
> + function:
> + const: flash
> + then:
> + properties:
> + groups:
> + enum: [snfi]
> + - if:
> + properties:
> + function:
> + const: pcie
> + then:
> + properties:
> + groups:
> + enum: [pcie_clk, pcie_wake, pcie_pereset]
> + - if:
> + properties:
> + function:
> + const: pwm
> + then:
> + properties:
> + groups:
> + enum: [pwm0, pwm1_0, pwm1_1]
> + - if:
> + properties:
> + function:
> + const: spi
> + then:
> + properties:
> + groups:
> + enum: [spi0, spi0_wp_hold, spi1_0, spi1_1, spi1_2, spi1_3]
> + - if:
> + properties:
> + function:
> + const: uart
> + then:
> + properties:
> + groups:
> + enum: [uart1_0, uart1_1, uart1_2, uart1_3_rx_tx,
> + uart1_3_cts_rts, uart2_0, uart2_1, uart0, uart1, uart2]
> + - if:
> + properties:
> + function:
> + const: watchdog
> + then:
> + properties:
> + groups:
> + enum: [watchdog]
> + - if:
> + properties:
> + function:
> + const: wifi
> + then:
> + properties:
> + groups:
> + enum: [wf_2g, wf_5g, wf_dbdc]
> + 'conf':
Same here. pattern or not?
> + type: object
> + additionalProperties: false
> + description: |
> + pinconf configuration nodes.
> + $ref: "/schemas/pinctrl/pincfg-node.yaml"
> +
> + properties:
> + pins:
> + description: |
> + An array of strings. Each string contains the name of a pin.
> + There is no PIN 41 to PIN 65 above on mt7686b, you can only use
> + those pins on mt7986a.
> + enum: [SYS_WATCHDOG, WF2G_LED, WF5G_LED, I2C_SCL, I2C_SDA, GPIO_0,
> + GPIO_1, GPIO_2, GPIO_3, GPIO_4, GPIO_5, GPIO_6, GPIO_7,
> + GPIO_8, GPIO_9, GPIO_10, GPIO_11, GPIO_12, GPIO_13, GPIO_14,
> + GPIO_15, PWM0, PWM1, SPI0_CLK, SPI0_MOSI, SPI0_MISO, SPI0_CS,
> + SPI0_HOLD, SPI0_WP, SPI1_CLK, SPI1_MOSI, SPI1_MISO, SPI1_CS,
> + SPI2_CLK, SPI2_MOSI, SPI2_MISO, SPI2_CS, SPI2_HOLD, SPI2_WP,
> + UART0_RXD, UART0_TXD, PCIE_PERESET_N, UART1_RXD, UART1_TXD,
> + UART1_CTS, UART1_RTS, UART2_RXD, UART2_TXD, UART2_CTS,
> + UART2_RTS, EMMC_DATA_0, EMMC_DATA_1, EMMC_DATA_2,
> + EMMC_DATA_3, EMMC_DATA_4, EMMC_DATA_5, EMMC_DATA_6,
> + EMMC_DATA_7, EMMC_CMD, EMMC_CK, EMMC_DSL, EMMC_RSTB, PCM_DTX,
> + PCM_DRX, PCM_CLK, PCM_FS, MT7531_INT, SMI_MDC, SMI_MDIO,
> + WF0_DIG_RESETB, WF0_CBA_RESETB, WF0_XO_REQ, WF0_TOP_CLK,
> + WF0_TOP_DATA, WF0_HB1, WF0_HB2, WF0_HB3, WF0_HB4, WF0_HB0,
> + WF0_HB0_B, WF0_HB5, WF0_HB6, WF0_HB7, WF0_HB8, WF0_HB9,
> + WF0_HB10, WF1_DIG_RESETB, WF1_CBA_RESETB, WF1_XO_REQ,
> + WF1_TOP_CLK, WF1_TOP_DATA, WF1_HB1, WF1_HB2, WF1_HB3,
> + WF1_HB4, WF1_HB0, WF1_HB0_B, WF1_HB5, WF1_HB6, WF1_HB7,
> + WF1_HB8]
> +
> + bias-disable: true
> +
> + bias-pull-up: true
> +
> + bias-pull-down: true
> +
> + input-enable: true
> +
> + input-disable: true
> +
> + output-enable: true
> +
> + output-low: true
> +
> + output-high: true
> +
> + input-schmitt-enable: true
> +
> + input-schmitt-disable: true
> +
> + drive-strength:
> + enum: [2, 4, 6, 8, 10, 12, 14, 16]
> +
> + mediatek,pull-up-adv:
> + description: |
> + Valid arguments for 'mediatek,pull-up-adv' are '0', '1', '2', '3'
> + Pull up setings for 2 pull resistors, R0 and R1. Valid arguments
> + are described as below:
> + 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
> + 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
> + 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
> + 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
> + $ref: /schemas/types.yaml#/definitions/uint32
> + enum: [0, 1, 2, 3]
> +
> + mediatek,pull-down-adv:
> + description: |
> + Valid arguments for 'mediatek,pull-up-adv' are '0', '1', '2', '3'
> + Pull down setings for 2 pull resistors, R0 and R1. Valid arguments
> + are described as below:
> + 0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
> + 1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
> + 2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
> + 3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
> + $ref: /schemas/types.yaml#/definitions/uint32
> + enum: [0, 1, 2, 3]
> +
> + required:
> + - pins
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/interrupt-controller/irq.h>
> + #include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> + soc {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + pio: pinctrl at 1001f000 {
> + compatible = "mediatek,mt7986a-pinctrl";
> + reg = <0 0x1001f000 0 0x1000>,
> + <0 0x11c30000 0 0x1000>,
> + <0 0x11c40000 0 0x1000>,
> + <0 0x11e20000 0 0x1000>,
> + <0 0x11e30000 0 0x1000>,
> + <0 0x11f00000 0 0x1000>,
> + <0 0x11f10000 0 0x1000>,
> + <0 0x1000b000 0 0x1000>;
> + reg-names = "gpio_base", "iocfg_rt_base", "iocfg_rb_base",
> + "iocfg_lt_base", "iocfg_lb_base", "iocfg_tr_base",
> + "iocfg_tl_base", "eint";
> + gpio-controller;
> + #gpio-cells = <2>;
> + gpio-ranges = <&pio 0 0 100>;
> + interrupt-controller;
> + interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-parent = <&gic>;
> + #interrupt-cells = <2>;
> +
> + uart1_pins: uart1-pins-42-to-45 {
> + mux {
> + function = "uart";
> + groups = "uart1";
> + };
> + };
> +
> + uart2_pins: uart1-pins-46-to-49 {
> + mux {
> + function = "uart";
> + groups = "uart2";
> + };
> + };
> +
> + };
> + };
> --
> 2.29.2
>
>
More information about the Linux-mediatek
mailing list