[PATCH v7 2/3] arm64: dts: mediatek: add basic mt7986a support
Sam Shih
sam.shih at mediatek.com
Mon Nov 15 17:39:49 PST 2021
Hi,
On Mon, 2021-11-15 at 17:27 +0100, Matthias Brugger wrote:
> Hi,
>
> On 18/10/2021 13:40, Sam Shih wrote:
> > Add basic chip support for Mediatek mt7986a, include
> > basic uart nodes, rng node and watchdog node.
> >
> > Add cpu node, timer node, gic node, psci and reserved-memory node
> > for ARM Trusted Firmware.
> >
>
> What is the exact difference between mt7986a and mt7986b? Right now,
> it's only
> the compatible, for that it makes no sense to split them.
>
The difference between mt7986a and mt7986b is pinout which described
in our pinctrl patch series
https://lore.kernel.org/all/20211022124036.5291-3-sam.shih@mediatek.com/
You are right, in this "basic SoC support" patch series, only show
compatible differences
> It would be good to see what the exact differences are, so that we
> can see if it
> makes sense to have one of the alternatives:
> 1) use a common mt7986.dtsi which get included by mt7986[a,b].dtsi
> 2) Use on mt7986.dtsi and only add one mt7986a.dtsi or mt7986b.dtsi
> which has
> add-ons.
>
In this case, can we use solution (1) to create a generic mt7986.dtsi
in this patch series, and add mt7986[a,b].dtsi to the dts part of the
pinctrl patch series to separate the difference nodes?
> > Signed-off-by: Sam Shih <sam.shih at mediatek.com>
> >
> > ---
> > v7: added memory node back to dts
> > v6: removed clock and pinctrl node, to separate basic part into a
> > single
> > patch series
> >
> > Original thread:
> >
https://urldefense.com/v3/__https://lore.kernel.org/all/20211004124155.1404-1-sam.shih@mediatek.com/__;!!CTRNKA9wMg0ARbw!xCEW0lwTKx4k272sWASoi90y_yRyQdAx0oNJC-jSAIWnIEkprJD-gAc1ugCvo0ex$
> >
> >
> > v5: follow reviewr's comment: removed clock freqency node in timer
> > due to
> > we have set CNTFRQ_EL0 in ATF firmware, and also corrected
> > GICD range
> > v4: added missing gic register bases, and fixed range of GICR
> > v3: used the stdout-path instead of console=ttyS0
> > v2: modified clock and uart node due to clock driver updated
> > ---
> > arch/arm64/boot/dts/mediatek/Makefile | 1 +
> > arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts | 38 +++++
> > arch/arm64/boot/dts/mediatek/mt7986a.dtsi | 149
> > +++++++++++++++++++
> > 3 files changed, 188 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> > create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a.dtsi
> >
> > diff --git a/arch/arm64/boot/dts/mediatek/Makefile
> > b/arch/arm64/boot/dts/mediatek/Makefile
> > index 4f68ebed2e31..e6c3a73b9e4a 100644
> > --- a/arch/arm64/boot/dts/mediatek/Makefile
> > +++ b/arch/arm64/boot/dts/mediatek/Makefile
> > @@ -7,6 +7,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
> > dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
> > dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
> > dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
> > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
> > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb
> > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm.dtb
> > dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb
> > diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> > b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> > new file mode 100644
> > index 000000000000..ca074cf8e578
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
> > @@ -0,0 +1,38 @@
> > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > +/*
> > + * Copyright (C) 2021 MediaTek Inc.
> > + * Author: Sam.Shih <sam.shih at mediatek.com>
> > + */
> > +
> > +/dts-v1/;
> > +#include "mt7986a.dtsi"
> > +
> > +/ {
> > + model = "MediaTek MT7986a RFB";
> > + compatible = "mediatek,mt7986a-rfb";
> > +
> > + aliases {
> > + serial0 = &uart0;
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial0:115200n8";
> > + bootargs = "earlycon=uart8250,mmio32,0x11002000
> > swiotlb=512";
>
> We normally don't add earlycon parameter to the normal bootargs, as
> it's only
> for debugging. Also what do we need the swiotlb? Are there any
> limitation in the
> HW that makes us need it?
>
Thank you for your suggestion, as far as I know, it should not have
hardware limitations. This bootargs is just inherent from mt7622-
rfb.dts, I will delete it and test again on our development board.
> Regards,
> Matthias
>
> > + };
> > +
> > + memory {
> > + reg = <0 0x40000000 0 0x40000000>;
> > + };
> > +};
> > +
> > +&uart0 {
> > + status = "okay";
> > +};
> > +
> > +&uart1 {
> > + status = "okay";
> > +};
> > +
> > +&uart2 {
> > + status = "okay";
> > +};
> > diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
> > b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
> > new file mode 100644
> > index 000000000000..75912bcf6c9c
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
> > @@ -0,0 +1,149 @@
> > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > +/*
> > + * Copyright (C) 2021 MediaTek Inc.
> > + * Author: Sam.Shih <sam.shih at mediatek.com>
> > + */
> > +
> > +#include <dt-bindings/interrupt-controller/irq.h>
> > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > +
> > +/ {
> > + compatible = "mediatek,mt7986a";
> > + interrupt-parent = <&gic>;
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > +
> > + system_clk: dummy40m {
> > + compatible = "fixed-clock";
> > + clock-frequency = <40000000>;
> > + #clock-cells = <0>;
> > + };
> > +
> > + cpus {
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + cpu0: cpu at 0 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53";
> > + enable-method = "psci";
> > + reg = <0x0>;
> > + #cooling-cells = <2>;
> > + };
> > +
> > + cpu1: cpu at 1 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53";
> > + enable-method = "psci";
> > + reg = <0x1>;
> > + #cooling-cells = <2>;
> > + };
> > +
> > + cpu2: cpu at 2 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a53";
> > + enable-method = "psci";
> > + reg = <0x2>;
> > + #cooling-cells = <2>;
> > + };
> > +
> > + cpu3: cpu at 3 {
> > + device_type = "cpu";
> > + enable-method = "psci";
> > + compatible = "arm,cortex-a53";
> > + reg = <0x3>;
> > + #cooling-cells = <2>;
> > + };
> > + };
> > +
> > + psci {
> > + compatible = "arm,psci-0.2";
> > + method = "smc";
> > + };
> > +
> > + reserved-memory {
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > + /* 192 KiB reserved for ARM Trusted Firmware (BL31) */
> > + secmon_reserved: secmon at 43000000 {
> > + reg = <0 0x43000000 0 0x30000>;
> > + no-map;
> > + };
> > + };
> > +
> > + timer {
> > + compatible = "arm,armv8-timer";
> > + interrupt-parent = <&gic>;
> > + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
> > + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
> > + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
> > + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
> > + };
> > +
> > + soc {
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + compatible = "simple-bus";
> > + ranges;
> > +
> > + gic: interrupt-controller at c000000 {
> > + compatible = "arm,gic-v3";
> > + #interrupt-cells = <3>;
> > + interrupt-parent = <&gic>;
> > + interrupt-controller;
> > + reg = <0 0x0c000000 0 0x10000>, /* GICD */
> > + <0 0x0c080000 0 0x80000>, /* GICR */
> > + <0 0x0c400000 0 0x2000>, /* GICC */
> > + <0 0x0c410000 0 0x1000>, /* GICH */
> > + <0 0x0c420000 0 0x2000>; /* GICV */
> > + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
> > + };
> > +
> > + watchdog: watchdog at 1001c000 {
> > + compatible = "mediatek,mt7986-wdt",
> > + "mediatek,mt6589-wdt";
> > + reg = <0 0x1001c000 0 0x1000>;
> > + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
> > + #reset-cells = <1>;
> > + status = "disabled";
> > + };
> > +
> > + trng: trng at 1020f000 {
> > + compatible = "mediatek,mt7986-rng",
> > + "mediatek,mt7623-rng";
> > + reg = <0 0x1020f000 0 0x100>;
> > + clocks = <&system_clk>;
> > + clock-names = "rng";
> > + status = "disabled";
> > + };
> > +
> > + uart0: serial at 11002000 {
> > + compatible = "mediatek,mt7986-uart",
> > + "mediatek,mt6577-uart";
> > + reg = <0 0x11002000 0 0x400>;
> > + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&system_clk>;
> > + status = "disabled";
> > + };
> > +
> > + uart1: serial at 11003000 {
> > + compatible = "mediatek,mt7986-uart",
> > + "mediatek,mt6577-uart";
> > + reg = <0 0x11003000 0 0x400>;
> > + interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&system_clk>;
> > + status = "disabled";
> > + };
> > +
> > + uart2: serial at 11004000 {
> > + compatible = "mediatek,mt7986-uart",
> > + "mediatek,mt6577-uart";
> > + reg = <0 0x11004000 0 0x400>;
> > + interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
> > + clocks = <&system_clk>;
> > + status = "disabled";
> > + };
> > +
> > + };
> > +
> > +};
> >
Regards,
Sam
More information about the Linux-mediatek
mailing list