[PATCH v2 3/5] net: stmmac: dwmac-mediatek: add support for mt8195
Biao Huang
biao.huang at mediatek.com
Thu Nov 11 18:40:07 PST 2021
Dear Angelo,
Thanks for your comments~
On Thu, 2021-11-11 at 14:26 +0100, AngeloGioacchino Del Regno wrote:
> Il 11/11/21 08:12, Biao Huang ha scritto:
> > Add Ethernet support for MediaTek SoCs from the mt8195 family.
> >
> > Signed-off-by: Biao Huang <biao.huang at mediatek.com>
> > ---
> > .../ethernet/stmicro/stmmac/dwmac-mediatek.c | 261
> > +++++++++++++++++-
> > 1 file changed, 260 insertions(+), 1 deletion(-)
> >
> > diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
> > b/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
> > index 6ea972e96665..b1266b68e21f 100644
> > --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
> > +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-mediatek.c
> > @@ -40,6 +40,33 @@
> > #define ETH_FINE_DLY_GTXC BIT(1)
> > #define ETH_FINE_DLY_RXC BIT(0)
> >
> > +/* Peri Configuration register for mt8195 */
> > +#define MT8195_PERI_ETH_CTRL0 0xFD0
> > +#define MT8195_RMII_CLK_SRC_INTERNAL BIT(28)
> > +#define MT8195_RMII_CLK_SRC_RXC BIT(27)
> > +#define MT8195_ETH_INTF_SEL GENMASK(26, 24)
> > +#define MT8195_RGMII_TXC_PHASE_CTRL BIT(22)
> > +#define MT8195_EXT_PHY_MODE BIT(21)
> > +#define MT8195_DLY_GTXC_INV BIT(12)
> > +#define MT8195_DLY_GTXC_ENABLE BIT(5)
> > +#define MT8195_DLY_GTXC_STAGES GENMASK(4, 0)
> > +
> > +#define MT8195_PERI_ETH_CTRL1 0xFD4
> > +#define MT8195_DLY_RXC_INV BIT(25)
> > +#define MT8195_DLY_RXC_ENABLE BIT(18)
> > +#define MT8195_DLY_RXC_STAGES GENMASK(17, 13)
> > +#define MT8195_DLY_TXC_INV BIT(12)
> > +#define MT8195_DLY_TXC_ENABLE BIT(5)
> > +#define MT8195_DLY_TXC_STAGES GENMASK(4, 0)
> > +
> > +#define MT8195_PERI_ETH_CTRL2 0xFD8
> > +#define MT8195_DLY_RMII_RXC_INV BIT(25)
> > +#define MT8195_DLY_RMII_RXC_ENABLE BIT(18)
> > +#define MT8195_DLY_RMII_RXC_STAGES GENMASK(17, 13)
> > +#define MT8195_DLY_RMII_TXC_INV BIT(12)
> > +#define MT8195_DLY_RMII_TXC_ENABLE BIT(5)
> > +#define MT8195_DLY_RMII_TXC_STAGES GENMASK(4, 0)
> > +
> > struct mac_delay_struct {
> > u32 tx_delay;
> > u32 rx_delay;
> > @@ -58,11 +85,13 @@ struct mediatek_dwmac_plat_data {
> > int num_clks_to_config;
> > bool rmii_clk_from_mac;
> > bool rmii_rxc;
> > + bool mac_wol;
> > };
> >
> > struct mediatek_dwmac_variant {
> > int (*dwmac_set_phy_interface)(struct mediatek_dwmac_plat_data
> > *plat);
> > int (*dwmac_set_delay)(struct mediatek_dwmac_plat_data *plat);
> > + void (*dwmac_fix_mac_speed)(void *priv, unsigned int speed);
> >
> > /* clock ids to be requested */
> > const char * const *clk_list;
> > @@ -78,6 +107,10 @@ static const char * const mt2712_dwmac_clk_l[]
> > = {
> > "axi", "apb", "mac_main", "ptp_ref", "rmii_internal"
> > };
> >
> > +static const char * const mt8195_dwmac_clk_l[] = {
> > + "axi", "apb", "mac_cg", "mac_main", "ptp_ref", "rmii_internal"
> > +};
> > +
> > static int mt2712_set_interface(struct mediatek_dwmac_plat_data
> > *plat)
> > {
> > int rmii_clk_from_mac = plat->rmii_clk_from_mac ?
> > RMII_CLK_SRC_INTERNAL : 0;
> > @@ -268,6 +301,204 @@ static const struct mediatek_dwmac_variant
> > mt2712_gmac_variant = {
> > .tx_delay_max = 17600,
> > };
> >
> > +static int mt8195_set_interface(struct mediatek_dwmac_plat_data
> > *plat)
> > +{
> > + int rmii_clk_from_mac = plat->rmii_clk_from_mac ?
> > MT8195_RMII_CLK_SRC_INTERNAL : 0;
> > + int rmii_rxc = plat->rmii_rxc ? MT8195_RMII_CLK_SRC_RXC : 0;
> > + u32 intf_val = 0;
> > +
> > + /* The clock labeled as "rmii_internal" in mt8195_dwmac_clk_l
> > is needed
> > + * only in RMII(when MAC provides the reference clock), and
> > useless for
> > + * RGMII/MII/RMII(when PHY provides the reference clock).
> > + * num_clks_to_config indicates the real number of clocks
> > should be
> > + * configured, equals to (plat->variant->num_clks - 1) in
> > default for all the case,
> > + * then +1 for rmii_clk_from_mac case.
> > + */
> > + plat->num_clks_to_config = plat->variant->num_clks - 1;
> > +
> > + /* select phy interface in top control domain */
> > + switch (plat->phy_mode) {
> > + case PHY_INTERFACE_MODE_MII:
> > + intf_val |= FIELD_PREP(MT8195_ETH_INTF_SEL,
> > PHY_INTF_MII);
> > + break;
> > + case PHY_INTERFACE_MODE_RMII:
> > + if (plat->rmii_clk_from_mac)
> > + plat->num_clks_to_config++;
> > + intf_val |= (rmii_rxc | rmii_clk_from_mac);
> > + intf_val |= FIELD_PREP(MT8195_ETH_INTF_SEL,
> > PHY_INTF_RMII);
> > + break;
> > + case PHY_INTERFACE_MODE_RGMII:
> > + case PHY_INTERFACE_MODE_RGMII_TXID:
> > + case PHY_INTERFACE_MODE_RGMII_RXID:
> > + case PHY_INTERFACE_MODE_RGMII_ID:
> > + intf_val |= FIELD_PREP(MT8195_ETH_INTF_SEL,
> > PHY_INTF_RGMII);
> > + break;
> > + default:
> > + dev_err(plat->dev, "phy interface not supported\n");
> > + return -EINVAL;
> > + }
> > +
> > + /* MT8195 only support external PHY */
> > + intf_val |= MT8195_EXT_PHY_MODE;
> > +
> > + regmap_write(plat->peri_regmap, MT8195_PERI_ETH_CTRL0,
> > intf_val);
> > +
> > + return 0;
> > +}
> > +
> > +static void mt8195_delay_ps2stage(struct mediatek_dwmac_plat_data
> > *plat)
> > +{
> > + struct mac_delay_struct *mac_delay = &plat->mac_delay;
> > +
> > + /* 290ps per stage */
> > + mac_delay->tx_delay /= 290;
> > + mac_delay->rx_delay /= 290;
> > +}
> > +
> > +static void mt8195_delay_stage2ps(struct mediatek_dwmac_plat_data
> > *plat)
> > +{
> > + struct mac_delay_struct *mac_delay = &plat->mac_delay;
> > +
> > + /* 290ps per stage */
> > + mac_delay->tx_delay *= 290;
> > + mac_delay->rx_delay *= 290;
> > +}
> > +
> > +static int mt8195_set_delay(struct mediatek_dwmac_plat_data *plat)
> > +{
> > + struct mac_delay_struct *mac_delay = &plat->mac_delay;
> > + u32 gtxc_delay_val, delay_val = 0, rmii_delay_val = 0;
> > +
> > + mt8195_delay_ps2stage(plat);
> > +
> > + switch (plat->phy_mode) {
> > + case PHY_INTERFACE_MODE_MII:
> > + delay_val |= FIELD_PREP(MT8195_DLY_TXC_ENABLE,
> > !!mac_delay->tx_delay);
> > + delay_val |= FIELD_PREP(MT8195_DLY_TXC_STAGES,
> > mac_delay->tx_delay);
> > + delay_val |= FIELD_PREP(MT8195_DLY_TXC_INV, mac_delay-
> > >tx_inv);
> > +
> > + delay_val |= FIELD_PREP(MT8195_DLY_RXC_ENABLE,
> > !!mac_delay->rx_delay);
> > + delay_val |= FIELD_PREP(MT8195_DLY_RXC_STAGES,
> > mac_delay->rx_delay);
> > + delay_val |= FIELD_PREP(MT8195_DLY_RXC_INV, mac_delay-
> > >rx_inv);
> > + break;
> > + case PHY_INTERFACE_MODE_RMII:
> > + if (plat->rmii_clk_from_mac) {
> > + /* case 1: mac provides the rmii reference
> > clock,
> > + * and the clock output to TXC pin.
> > + * The egress timing can be adjusted by
> > RMII_TXC delay macro circuit.
> > + * The ingress timing can be adjusted by
> > RMII_RXC delay macro circuit.
> > + */
> > + rmii_delay_val |=
> > FIELD_PREP(MT8195_DLY_RMII_TXC_ENABLE,
> > + !!mac_delay-
> > >tx_delay);
> > + rmii_delay_val |=
> > FIELD_PREP(MT8195_DLY_RMII_TXC_STAGES,
> > + mac_delay-
> > >tx_delay);
> > + rmii_delay_val |=
> > FIELD_PREP(MT8195_DLY_RMII_TXC_INV,
> > + mac_delay-
> > >tx_inv);
> > +
> > + rmii_delay_val |=
> > FIELD_PREP(MT8195_DLY_RMII_RXC_ENABLE,
> > + !!mac_delay-
> > >rx_delay);
> > + rmii_delay_val |=
> > FIELD_PREP(MT8195_DLY_RMII_RXC_STAGES,
> > + mac_delay-
> > >rx_delay);
> > + rmii_delay_val |=
> > FIELD_PREP(MT8195_DLY_RMII_RXC_INV,
> > + mac_delay-
> > >rx_inv);
> > + } else {
> > + /* case 2: the rmii reference clock is from
> > external phy,
> > + * and the property "rmii_rxc" indicates which
> > pin(TXC/RXC)
> > + * the reference clk is connected to. The
> > reference clock is a
> > + * received signal, so rx_delay/rx_inv are used
> > to indicate
> > + * the reference clock timing adjustment
> > + */
> > + if (plat->rmii_rxc) {
> > + /* the rmii reference clock from
> > outside is connected
> > + * to RXC pin, the reference clock will
> > be adjusted
> > + * by RXC delay macro circuit.
> > + */
> > + delay_val |=
> > FIELD_PREP(MT8195_DLY_RXC_ENABLE,
> > + !!mac_delay-
> > >rx_delay);
> > + delay_val |=
> > FIELD_PREP(MT8195_DLY_RXC_STAGES,
> > + mac_delay-
> > >rx_delay);
> > + delay_val |=
> > FIELD_PREP(MT8195_DLY_RXC_INV,
> > + mac_delay-
> > >rx_inv);
> > + } else {
> > + /* the rmii reference clock from
> > outside is connected
> > + * to TXC pin, the reference clock will
> > be adjusted
> > + * by TXC delay macro circuit.
> > + */
> > + delay_val |=
> > FIELD_PREP(MT8195_DLY_TXC_ENABLE,
> > + !!mac_delay-
> > >rx_delay);
> > + delay_val |=
> > FIELD_PREP(MT8195_DLY_TXC_STAGES,
> > + mac_delay-
> > >rx_delay);
> > + delay_val |=
> > FIELD_PREP(MT8195_DLY_TXC_INV,
> > + mac_delay-
> > >rx_inv);
> > + }
> > + }
> > + break;
> > + case PHY_INTERFACE_MODE_RGMII:
> > + case PHY_INTERFACE_MODE_RGMII_TXID:
> > + case PHY_INTERFACE_MODE_RGMII_RXID:
> > + case PHY_INTERFACE_MODE_RGMII_ID:
> > + gtxc_delay_val |= FIELD_PREP(MT8195_DLY_GTXC_ENABLE,
> > !!mac_delay->tx_delay);
> > + gtxc_delay_val |= FIELD_PREP(MT8195_DLY_GTXC_STAGES,
> > mac_delay->tx_delay);
> > + gtxc_delay_val |= FIELD_PREP(MT8195_DLY_GTXC_INV,
> > mac_delay->tx_inv);
> > +
> > + delay_val |= FIELD_PREP(MT8195_DLY_RXC_ENABLE,
> > !!mac_delay->rx_delay);
> > + delay_val |= FIELD_PREP(MT8195_DLY_RXC_STAGES,
> > mac_delay->rx_delay);
> > + delay_val |= FIELD_PREP(MT8195_DLY_RXC_INV, mac_delay-
> > >rx_inv);
> > +
> > + break;
> > + default:
> > + dev_err(plat->dev, "phy interface not supported\n");
> > + return -EINVAL;
> > + }
> > +
> > + regmap_update_bits(plat->peri_regmap,
> > + MT8195_PERI_ETH_CTRL0,
> > + MT8195_RGMII_TXC_PHASE_CTRL |
> > + MT8195_DLY_GTXC_INV |
> > + MT8195_DLY_GTXC_ENABLE |
> > + MT8195_DLY_GTXC_STAGES,
> > + gtxc_delay_val);
> > + regmap_write(plat->peri_regmap, MT8195_PERI_ETH_CTRL1,
> > delay_val);
> > + regmap_write(plat->peri_regmap, MT8195_PERI_ETH_CTRL2,
> > rmii_delay_val);
> > +
> > + mt8195_delay_stage2ps(plat);
> > +
> > + return 0;
> > +}
> > +
> > +static void mt8195_fix_mac_speed(void *priv, unsigned int speed)
> > +{
> > + struct mediatek_dwmac_plat_data *priv_plat = priv;
> > +
> > + if ((phy_interface_mode_is_rgmii(priv_plat->phy_mode))) {
> > + /* prefer 2ns fixed delay which is controlled by
> > TXC_PHASE_CTRL,
> > + * when link speed is 1Gbps with RGMII interface,
> > + * Fall back to delay macro circuit for 10/100Mbps link
> > speed.
> > + */
> > + if (speed == SPEED_1000)
> > + regmap_update_bits(priv_plat->peri_regmap,
> > + MT8195_PERI_ETH_CTRL0,
> > + MT8195_RGMII_TXC_PHASE_CTRL
> > |
> > + MT8195_DLY_GTXC_ENABLE |
> > + MT8195_DLY_GTXC_INV |
> > + MT8195_DLY_GTXC_STAGES,
> > + MT8195_RGMII_TXC_PHASE_CTRL)
> > ;
> > + else
> > + mt8195_set_delay(priv_plat);
> > + }
> > +}
> > +
> > +static const struct mediatek_dwmac_variant mt8195_gmac_variant = {
> > + .dwmac_set_phy_interface = mt8195_set_interface,
> > + .dwmac_set_delay = mt8195_set_delay,
> > + .dwmac_fix_mac_speed = mt8195_fix_mac_speed,
> > + .clk_list = mt8195_dwmac_clk_l,
> > + .num_clks = ARRAY_SIZE(mt8195_dwmac_clk_l),
> > + .dma_bit_mask = 35,
> > + .rx_delay_max = 9280,
> > + .tx_delay_max = 9280,
> > +};
> > +
> > static int mediatek_dwmac_config_dt(struct
> > mediatek_dwmac_plat_data *plat)
> > {
> > struct mac_delay_struct *mac_delay = &plat->mac_delay;
> > @@ -308,6 +539,7 @@ static int mediatek_dwmac_config_dt(struct
> > mediatek_dwmac_plat_data *plat)
> > mac_delay->rx_inv = of_property_read_bool(plat->np,
> > "mediatek,rxc-inverse");
> > plat->rmii_rxc = of_property_read_bool(plat->np,
> > "mediatek,rmii-rxc");
> > plat->rmii_clk_from_mac = of_property_read_bool(plat->np,
> > "mediatek,rmii-clk-from-mac");
> > + plat->mac_wol = of_property_read_bool(plat->np, "mediatek,mac-
> > wol");
> >
> > return 0;
> > }
> > @@ -384,6 +616,16 @@ static int mediatek_dwmac_clks_config(void
> > *priv, bool enabled)
> >
> > return ret;
> > }
> > +
> > +static void mediatek_fix_mac_speed(void *priv, unsigned int speed)
> > +{
> > + struct mediatek_dwmac_plat_data *plat = priv;
> > + const struct mediatek_dwmac_variant *variant = plat->variant;
> > +
> > + if (variant->dwmac_fix_mac_speed)
> > + variant->dwmac_fix_mac_speed(priv, speed);
> > +}
> > +
> > static int mediatek_dwmac_probe(struct platform_device *pdev)
> > {
> > struct mediatek_dwmac_plat_data *priv_plat;
> > @@ -421,7 +663,7 @@ static int mediatek_dwmac_probe(struct
> > platform_device *pdev)
> > return PTR_ERR(plat_dat);
> >
> > plat_dat->interface = priv_plat->phy_mode;
> > - plat_dat->use_phy_wol = 1;
> > + plat_dat->use_phy_wol = priv_plat->mac_wol ? 0 : 1;
> > plat_dat->riwt_off = 1;
> > plat_dat->maxmtu = ETH_DATA_LEN;
> > plat_dat->addr64 = priv_plat->variant->dma_bit_mask;
> > @@ -429,7 +671,22 @@ static int mediatek_dwmac_probe(struct
> > platform_device *pdev)
> > plat_dat->init = mediatek_dwmac_init;
> > plat_dat->exit = mediatek_dwmac_exit;
> > plat_dat->clks_config = mediatek_dwmac_clks_config;
> > + plat_dat->fix_mac_speed = mediatek_fix_mac_speed;
>
>
>
> So, since that function serves as a wrapper only....
>
>
>
> if (priv_plat->variant->dwmac_fix_mac_speed)
>
> lat_dat->fix_mac_speed = priv_plat->variant-
> >dwmac_fix_mac_speed;
>
>
>
> seems to be a good option :)
>
Yes, that makes sense, will fix it in next send.
>
>
>
>
> Regards,
>
> - Angelo
>
More information about the Linux-mediatek
mailing list