[v8,5/7] PCI: mediatek-gen3: Add MSI support

[Marc Zyngier]

On Wed, 10 Mar 2021 06:48:49 +0000,
Jianjun Wang <jianjun.wang at mediatek.com> wrote:
> > > +static struct irq_chip mtk_msi_irq_chip = {
> > > +	.name = "MSI",
> > > +	.irq_enable = mtk_pcie_irq_unmask,
> > > +	.irq_disable = mtk_pcie_irq_mask,
> > 
> > Same comment as for the previous patch: enable/disable serve no
> > purpose here.
> 
> Replied in the previous patch, the enable/disable callback is used when
> the system suspend/resume.

As I said, your suspend/resume should be self contained, and not rely
on the irq subsystem to restore a viable state.

[...]

> > > @@ -408,6 +677,14 @@ static void mtk_pcie_irq_handler(struct irq_desc *desc)
> > >  		generic_handle_irq(virq);
> > >  	}
> > >  
> > > +	irq_bit = PCIE_MSI_SHIFT;
> > > +	for_each_set_bit_from(irq_bit, &status, PCIE_MSI_SET_NUM +
> > > +			      PCIE_MSI_SHIFT) {
> > > +		mtk_pcie_msi_handler(port, irq_bit - PCIE_MSI_SHIFT);
> > > +
> > > +		writel_relaxed(BIT(irq_bit), port->base + PCIE_INT_STATUS_REG);
> > 
> > Isn't this write the same thing you have for EOI in the INTx case?
> > While I could understand your description in that case (this is a
> > resampling operation), I don't get what this does here. Either this is
> > also an EOI, but your initial description doesn't make sense, or it is
> > an Ack, and it should be moved to the right place.
> > 
> > Which one is it?
> 
> I think it should be an EOI which used to clear the interrupt status of
> a single set in the PCIe intc field, maybe I should move it to the end
> of the mtk_pcie_msi_handler() function.

I doubt this is an EOI. If, as I suspect, it instructs the HW to clear
the bit so that new pending bits can be recorded, it must take place
*before* the interrupt is handled, or you may lose MSIs in the
interval between the handling of the interrupt and the clearing of the
pending bit. To satisfy this requirement, this should be an ACK, which
is consistent with the way most MSI controllers such as this one work.

> 
>                   +-----+
>                   | GIC |
>                   +-----+
>                      ^
>                      |
>                  port->irq
>                      |
>              +-+-+-+-+-+-+-+-+
>              |0|1|2|3|4|5|6|7| (PCIe intc)
>              +-+-+-+-+-+-+-+-+
>               ^ ^           ^
>               | |    ...    |
>       +-------+ +------+    +-----------+
>       |                |                |
> +-+-+---+--+--+  +-+-+---+--+--+  +-+-+---+--+--+
> |0|1|...|30|31|  |0|1|...|30|31|  |0|1|...|30|31| (MSI sets)
> +-+-+---+--+--+  +-+-+---+--+--+  +-+-+---+--+--+
>  ^ ^      ^  ^    ^ ^      ^  ^    ^ ^      ^  ^
>  | |      |  |    | |      |  |    | |      |  |  (MSI vectors)
>  | |      |  |    | |      |  |    | |      |  |
> 
>   (MSI SET0)       (MSI SET1)  ...   (MSI SET7)
> 
> I would like to ask another question. In this interrupt architecture, we
> cannot implement an affinity for PCIe interrupts, so we return a
> negative value in the mtk_pcie_set_affinity callback as follows: 
> 
> +static int mtk_pcie_set_affinity(struct irq_data *data,
> +                                const struct cpumask *mask, bool force)
> +{
> +       return -EINVAL;
> +}
> 
> But there will always be error logs when hotplug a CPU:
> 
> ~ # echo 0 > /sys/devices/system/cpu/cpu1/online
> [   93.633059] IRQ255: set affinity failed(-22).
> [   93.633624] IRQ256: set affinity failed(-22).
> [   93.634222] CPU1: shutdown
> [   93.634586] psci: CPU1 killed (polled 0 ms)
> 
> Or when the system suspends:
> 
> ~ # echo mem > /sys/power/state
> [   93.635145] cpuhp: cpu_off cluster=0, cpu=1
> [  169.835653] PM: suspend entry (deep)
> [  169.836717] Filesystems sync: 0.000 seconds
> [  169.837924] Freezing user space processes ... (elapsed 0.001 seconds)
> done.
> [  169.839922] OOM killer disabled.
> [  169.840336] Freezing remaining freezable tasks ... (elapsed 0.001
> seconds) done.
> [  169.844715] Disabling non-boot CPUs ...
> [  169.846443] IRQ255: set affinity failed(-22).
> [  169.847002] IRQ256: set affinity failed(-22).
> [  169.847586] CPU2: shutdown
> [  169.847943] psci: CPU2 killed (polled 0 ms)
> [  169.848489] cpuhp: cpu_off cluster=0, cpu=2
> [  169.850285] IRQ255: set affinity failed(-22).
> [  169.851369] IRQ256: set affinity failed(-22).
> ...
> 
> Sometimes this can cause misunderstandings to users, do we have a chance
> to prevent this error log?

No. This HW doesn't allow MSIs to be individually retargeted, and the
kernel isn't happy about that. That's one of the many reasons why
hiding MSIs behind a mux (or two in your case) is a *very bad idea*.

Thanks,

	M.

-- 
Without deviation from the norm, progress is not possible.