[PATCH] irqchip/irq-mst: Support polarity configuration

Daniel Palmer daniel at 0x0f.com
Mon Mar 8 13:06:05 GMT 2021


Hi Mark-PK,

On Mon, 8 Mar 2021 at 11:42, Mark-PK Tsai (蔡沛剛)
<Mark-PK.Tsai at mediatek.com> wrote:
> > It seems like the polarity of interrupts is always the same between the MStar intc and the GIC? Low level interrupts are handled in the mstar intc and become high level interrupts to the GIC?
> > I think for the Mstar MSC313(e) and SigmaStar chips all of the internal interrupts are high level so I never noticed this behaviour.
> > I can't remember seeing anything that handled this in the MStar kernel code I looked at.
> > Is this specific to a certain chip or does it apply for everything with this intc?
>
> I suppose Mstar SoCs also need this patch which depends on what kind of interrupt source the HW designer wire to this intc.
> If an interrupt source is active low, we need to set the corresponding bit to reverse the polarity to meet GIC SPI requirement as Marc mentioned.

That makes sense. Looking back at the original MStar driver again they
did handle reversing the polarity but they passed the original
polarity through to the GIC too.
So maybe it never worked properly. :)

I think I can test this with GPIOs that are wired into the mstar intc
on the MStar/SigmaStar chips. I'll get back to you with how that works
out.

Thanks,

Daniel



>
> > The register values being lost if the chip goes into suspend to memory makes sense for the MStar chips too I think as everything that is not in the "pmsleep" register group seems to be lost.
>
> There are mask and eoi bits I did not handle here.
> That's because kernel will handle the mask and eoi status when system going to suspend/resume in suspend_device_irqs/ resume_device_irqs.
> And all the irqs of Mstar intc are masked by default when the IP powered on.
>
>
> Best regards,
> Mark-PK Tsai
>
>
> -----Original Message-----
> From: Marc Zyngier [mailto:maz at kernel.org]
> Sent: Sunday, March 7, 2021 2:28 AM
> To: Daniel Palmer <daniel at 0x0f.com>
> Cc: Mark-PK Tsai (蔡沛剛) <Mark-PK.Tsai at mediatek.com>; Daniel Palmer <daniel at thingy.jp>; Thomas Gleixner <tglx at linutronix.de>; Jason Cooper <jason at lakedaemon.net>; Matthias Brugger <matthias.bgg at gmail.com>; Linux Kernel Mailing List <linux-kernel at vger.kernel.org>; linux-arm-kernel <linux-arm-kernel at lists.infradead.org>; linux-mediatek at lists.infradead.org; YJ Chiang (江英杰) <yj.chiang at mediatek.com>
> Subject: Re: [PATCH] irqchip/irq-mst: Support polarity configuration
>
> On Sat, 06 Mar 2021 17:06:51 +0000,
> Daniel Palmer <daniel at 0x0f.com> wrote:
> >
> > Hi Mark-PK,
> >
> > I'm trying to understand the logic behind the changes.
> > It seems like the polarity of interrupts is always the same between
> > the MStar intc and the GIC? Low level interrupts are handled in the
> > mstar intc and become high level interrupts to the GIC?
>
> That's because the GIC only supports level-high input interrupts when they are level triggered (and rising edge when edge triggered).
>
> Thanks,
>
>         M.
>
> --
> Without deviation from the norm, progress is not possible.



More information about the Linux-mediatek mailing list