[PATCH v5 05/14] media: mtk-vcodec: venc: support START and STOP commands

[Alexandre Courbot]

Hi Dafna, sorry for (again) taking so long to come back to this! >_<

On Fri, May 28, 2021 at 4:03 PM Dafna Hirschfeld
<dafna.hirschfeld at collabora.com> wrote:
>
> Hi,
>
> I applied this patchset and tested the stateful encoder on debian with the command:
>
> [gst-master] root at debian:~/gst-build# gst-launch-1.0 filesrc location=images/jelly-800-640.YU12 ! rawvideoparse width=800 height=640 format=i420 ! videoconvert ! v4l2h264enc ! h264parse ! mp4mux ! filesink location=jelly-800-640.mp4
>
> I get:
>
> Setting pipeline[   79.703879] [MTK_V4L2] level=0 fops_vcodec_open(),190: encoder capability 10000000
>   to PAUSED ...
> Pipeline is PREROLLING ...
> Redistribute latency...
> [   80.621076] mtk-iommu 10205000.iommu: Partial TLB flush timed out, falling back to full flush
> [   80.631232] mtk-iommu 10205000.iommu: Partial TLB flush timed out, falling back to full flush
> [   80.640878] mtk-iommu 10205000.iommu: Partial TLB flush timed out, falling back to full flush
> [   80.650766] mtk-iommu 10205000.iommu: Partial TLB flush timed out, falling back to full flush
> [   80.660430] mtk-iommu 10205000.iommu: Partial TLB flush timed out, falling back to full flush
> [   80.670194] mtk-iommu 10205000.iommu: Partial TLB flush timed out, falling back to full flush
> [   80.680967] mtk-iommu 10205000.iommu: Partial TLB flush timed out, falling back to full flush
> [   80.691376] mtk-iommu 10205000.iommu: Partial TLB flush timed out, falling back to full flush
> [   80.701718] mtk-iommu 10205000.iommu: Partial TLB flush timed out, falling back to full flush
> [   80.712106] mtk-iommu 10205000.iommu: Partial TLB flush timed out, falling back to full flush
> [   80.722272] [MTK_V4L2] level=0 mtk_venc_set_param(),371: fmt 0x3, P/L 0/0, w/h 800/640, buf 800/640, fps/bps 25/4000000, gop 0, i_period 0
> Pipeline is PREROLLED ...
> Setting pipeline to PLAYING ...
> New clock: GstSystemClock
> [   81.918747] [MTK_V4L2][ERROR] mtk_vcodec_wait_for_done_ctx:32: [3] ctx->type=1, cmd=1, wait_event_interruptible_timeout time=1000ms out 0 0!
> [   81.931392] [MTK_VCODEC][ERROR][3]: h264_encode_frame() irq_status=0 failed
> [   81.938470] [MTK_V4L2][ERROR] mtk_venc_worker:1219: venc_if_encode failed=-5
> [   82.974746] [MTK_V4L2][ERROR] mtk_vcodec_wait_for_done_ctx:32: [3] ctx->type=1, cmd=1, wait_event_interruptible_timeout time=1000ms out 0 0!
> [   82.987392] [MTK_VCODEC][ERROR][3]: h264_encode_frame() irq_status=0 failed
> [   82.994471] [MTK_V4L2][ERROR] mtk_venc_worker:1219: venc_if_encode failed=-5
> [  104.163977] cros-ec-dev cros-ec-dev.2.auto: Some logs may have been dropped...
> 0:00:00.4 / 99:99:99.
> 0:00:00.4 / 99:99:99.
> 0:00:00.4 / 99:99:99.
> 0:00:00.4 / 99:99:99.
> 0:00:00.4 / 99:99:99.
> 0:00:00.4 / 99:99:99.
> 0:00:00.4 / 99:99:99.
> 0:00:00.4 / 99:99:99.
> 0:00:00.4 / 99:99:99.
> 0:00:00.4 / 99:99:99.
> ^Chandling interrupt.
>
> And then the streaming hangs. The same error happens without this patchset, but without
> this patchset the statful encoder does not support V4L2_ENC_CMD_STOP/START needed by the spec.
> I am not sure what cause the error and wether those mtk-iommu erros has to do with that. The issue
> could also come from the mtk-vpu used by the encoder.
> Do you have any idea where this can come from?

Mmm, this looks like the firmware is unhappy about something and
hangs. I wonder if the IOMMU messages above could not be linked to
that, I remember seeing similar problems when the buffers were not
properly synced on the device side.

I'll try and see if I can deploy gstreamer on the old MT8173
Chromebook I am using to see if I have more success here, but no
guarantee I can test in the same conditions as you unfortunately. :/

The MTK folks are the most qualified to look into this issue though.
Yunfei, do you have any idea about why this is happening?