[PATCH v4 3/8] i2c: mediatek: Reset the handshake signal between i2c and dma
Chen-Yu Tsai
wenst at chromium.org
Wed Aug 11 01:41:04 PDT 2021
Hi,
On Sat, Jul 17, 2021 at 6:29 PM Kewei Xu <kewei.xu at mediatek.com> wrote:
>
> Due to changes in the hardware design of the handshaking signal
> between i2c and dma, it is necessary to reset the handshaking
> signal before each transfer to ensure that the multi-msgs can
> be transferred correctly.
This also affects MT8192. Has this been tested on that SoC as well?
> Signed-off-by: Kewei Xu <kewei.xu at mediatek.com>
> ---
> drivers/i2c/busses/i2c-mt65xx.c | 14 ++++++++++++++
> 1 file changed, 14 insertions(+)
>
> diff --git a/drivers/i2c/busses/i2c-mt65xx.c b/drivers/i2c/busses/i2c-mt65xx.c
> index 222ff765e55d..c0108387f34b 100644
> --- a/drivers/i2c/busses/i2c-mt65xx.c
> +++ b/drivers/i2c/busses/i2c-mt65xx.c
> @@ -47,6 +47,9 @@
> #define I2C_RD_TRANAC_VALUE 0x0001
> #define I2C_SCL_MIS_COMP_VALUE 0x0000
> #define I2C_CHN_CLR_FLAG 0x0000
> +#define I2C_CLR_DEBUGCTR 0x0000
> +#define I2C_RELIABILITY 0x0010
> +#define I2C_DMAACK_ENABLE 0x0008
>
> #define I2C_DMA_CON_TX 0x0000
> #define I2C_DMA_CON_RX 0x0001
> @@ -850,6 +853,17 @@ static int mtk_i2c_do_transfer(struct mtk_i2c *i2c, struct i2c_msg *msgs,
>
> reinit_completion(&i2c->msg_complete);
>
> + if (i2c->dev_comp->apdma_sync) {
> + mtk_i2c_writew(i2c, I2C_CLR_DEBUGCTR, OFFSET_DEBUGCTRL);
> + writel(I2C_DMA_HANDSHAKE_RST | I2C_DMA_WARM_RST,
> + i2c->pdmabase + OFFSET_RST);
> + writel(I2C_DMA_CLR_FLAG, i2c->pdmabase + OFFSET_RST);
I2C_DMA_WARM_RST is self-clearing. Is I2C_DMA_HANDSHAKE_RST not
self-clearing? If both are self-clearing, don't you need to wait and
check for them to cleared? If they aren't self-clearing, do you need
to delay some time for them to complete?
> + mtk_i2c_writew(i2c, I2C_HANDSHAKE_RST, OFFSET_SOFTRESET);
> + mtk_i2c_writew(i2c, I2C_CHN_CLR_FLAG, OFFSET_SOFTRESET);
Same here. No time delay needed?
> + mtk_i2c_writew(i2c, I2C_RELIABILITY | I2C_DMAACK_ENABLE,
> + OFFSET_DEBUGCTRL);
A comment explaining what the section above does would be nice. AFAICU
this is force resetting the DMA handling.
Regards
ChenYu
> + }
> +
> control_reg = mtk_i2c_readw(i2c, OFFSET_CONTROL) &
> ~(I2C_CONTROL_DIR_CHANGE | I2C_CONTROL_RS);
> if ((i2c->speed_hz > I2C_MAX_FAST_MODE_PLUS_FREQ) || (left_num >= 1))
> --
> 2.18.0
> _______________________________________________
> Linux-mediatek mailing list
> Linux-mediatek at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-mediatek
More information about the Linux-mediatek
mailing list