[RFC v4 net-next 2/4] net: dsa: mt7530: add interrupt support
Marc Zyngier
maz at kernel.org
Mon Apr 12 09:21:12 BST 2021
On Mon, 12 Apr 2021 04:42:35 +0100,
DENG Qingfang <dqfext at gmail.com> wrote:
>
> Add support for MT7530 interrupt controller to handle internal PHYs.
> In order to assign an IRQ number to each PHY, the registration of MDIO bus
> is also done in this driver.
>
> Signed-off-by: DENG Qingfang <dqfext at gmail.com>
> ---
> RFC v3 -> RFC v4:
> - No changes.
>
> drivers/net/dsa/Kconfig | 1 +
> drivers/net/dsa/mt7530.c | 266 +++++++++++++++++++++++++++++++++++----
> drivers/net/dsa/mt7530.h | 20 ++-
> 3 files changed, 258 insertions(+), 29 deletions(-)
>
> diff --git a/drivers/net/dsa/Kconfig b/drivers/net/dsa/Kconfig
> index a5f1aa911fe2..264384449f09 100644
> --- a/drivers/net/dsa/Kconfig
> +++ b/drivers/net/dsa/Kconfig
> @@ -36,6 +36,7 @@ config NET_DSA_LANTIQ_GSWIP
> config NET_DSA_MT7530
> tristate "MediaTek MT753x and MT7621 Ethernet switch support"
> select NET_DSA_TAG_MTK
> + select MEDIATEK_PHY
> help
> This enables support for the MediaTek MT7530, MT7531, and MT7621
> Ethernet switch chips.
> diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
> index 2bd1bab71497..da033004a74d 100644
> --- a/drivers/net/dsa/mt7530.c
> +++ b/drivers/net/dsa/mt7530.c
> @@ -10,6 +10,7 @@
> #include <linux/mfd/syscon.h>
> #include <linux/module.h>
> #include <linux/netdevice.h>
> +#include <linux/of_irq.h>
> #include <linux/of_mdio.h>
> #include <linux/of_net.h>
> #include <linux/of_platform.h>
> @@ -596,18 +597,14 @@ mt7530_mib_reset(struct dsa_switch *ds)
> mt7530_write(priv, MT7530_MIB_CCR, CCR_MIB_ACTIVATE);
> }
>
> -static int mt7530_phy_read(struct dsa_switch *ds, int port, int regnum)
> +static int mt7530_phy_read(struct mt7530_priv *priv, int port, int regnum)
> {
> - struct mt7530_priv *priv = ds->priv;
> -
> return mdiobus_read_nested(priv->bus, port, regnum);
> }
>
> -static int mt7530_phy_write(struct dsa_switch *ds, int port, int regnum,
> +static int mt7530_phy_write(struct mt7530_priv *priv, int port, int regnum,
> u16 val)
> {
> - struct mt7530_priv *priv = ds->priv;
> -
> return mdiobus_write_nested(priv->bus, port, regnum, val);
> }
>
> @@ -785,9 +782,8 @@ mt7531_ind_c22_phy_write(struct mt7530_priv *priv, int port, int regnum,
> }
>
> static int
> -mt7531_ind_phy_read(struct dsa_switch *ds, int port, int regnum)
> +mt7531_ind_phy_read(struct mt7530_priv *priv, int port, int regnum)
> {
> - struct mt7530_priv *priv = ds->priv;
> int devad;
> int ret;
>
> @@ -803,10 +799,9 @@ mt7531_ind_phy_read(struct dsa_switch *ds, int port, int regnum)
> }
>
> static int
> -mt7531_ind_phy_write(struct dsa_switch *ds, int port, int regnum,
> +mt7531_ind_phy_write(struct mt7530_priv *priv, int port, int regnum,
> u16 data)
> {
> - struct mt7530_priv *priv = ds->priv;
> int devad;
> int ret;
>
> @@ -822,6 +817,22 @@ mt7531_ind_phy_write(struct dsa_switch *ds, int port, int regnum,
> return ret;
> }
>
> +static int
> +mt753x_phy_read(struct mii_bus *bus, int port, int regnum)
> +{
> + struct mt7530_priv *priv = bus->priv;
> +
> + return priv->info->phy_read(priv, port, regnum);
> +}
> +
> +static int
> +mt753x_phy_write(struct mii_bus *bus, int port, int regnum, u16 val)
> +{
> + struct mt7530_priv *priv = bus->priv;
> +
> + return priv->info->phy_write(priv, port, regnum, val);
> +}
> +
> static void
> mt7530_get_strings(struct dsa_switch *ds, int port, u32 stringset,
> uint8_t *data)
> @@ -1828,6 +1839,211 @@ mt7530_setup_gpio(struct mt7530_priv *priv)
> }
> #endif /* CONFIG_GPIOLIB */
>
> +static irqreturn_t
> +mt7530_irq_thread_fn(int irq, void *dev_id)
> +{
> + struct mt7530_priv *priv = dev_id;
> + bool handled = false;
> + u32 val;
> + int p;
> +
> + mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED);
> + val = mt7530_mii_read(priv, MT7530_SYS_INT_STS);
> + mt7530_mii_write(priv, MT7530_SYS_INT_STS, val);
> + mutex_unlock(&priv->bus->mdio_lock);
> +
> + for (p = 0; p < MT7530_NUM_PHYS; p++) {
> + if (BIT(p) & val) {
> + unsigned int irq;
> +
> + irq = irq_find_mapping(priv->irq_domain, p);
> + handle_nested_irq(irq);
> + handled = true;
> + }
> + }
> +
> + return IRQ_RETVAL(handled);
> +}
> +
> +static void
> +mt7530_irq_mask(struct irq_data *d)
> +{
> + struct mt7530_priv *priv = irq_data_get_irq_chip_data(d);
> +
> + priv->irq_enable &= ~BIT(d->hwirq);
> +}
> +
> +static void
> +mt7530_irq_unmask(struct irq_data *d)
> +{
> + struct mt7530_priv *priv = irq_data_get_irq_chip_data(d);
> +
> + priv->irq_enable |= BIT(d->hwirq);
> +}
> +
> +static void
> +mt7530_irq_bus_lock(struct irq_data *d)
> +{
> + struct mt7530_priv *priv = irq_data_get_irq_chip_data(d);
> +
> + mutex_lock_nested(&priv->bus->mdio_lock, MDIO_MUTEX_NESTED);
> +}
> +
> +static void
> +mt7530_irq_bus_sync_unlock(struct irq_data *d)
> +{
> + struct mt7530_priv *priv = irq_data_get_irq_chip_data(d);
> +
> + mt7530_mii_write(priv, MT7530_SYS_INT_EN, priv->irq_enable);
> + mutex_unlock(&priv->bus->mdio_lock);
> +}
> +
> +static struct irq_chip mt7530_irq_chip = {
> + .name = KBUILD_MODNAME,
> + .irq_mask = mt7530_irq_mask,
> + .irq_unmask = mt7530_irq_unmask,
> + .irq_bus_lock = mt7530_irq_bus_lock,
> + .irq_bus_sync_unlock = mt7530_irq_bus_sync_unlock,
> +};
> +
> +static int
> +mt7530_irq_map(struct irq_domain *domain, unsigned int irq,
> + irq_hw_number_t hwirq)
> +{
> + irq_set_chip_data(irq, domain->host_data);
> + irq_set_chip_and_handler(irq, &mt7530_irq_chip, handle_simple_irq);
> + irq_set_nested_thread(irq, true);
> + irq_set_noprobe(irq);
> +
> + return 0;
> +}
> +
> +static const struct irq_domain_ops mt7530_irq_domain_ops = {
> + .map = mt7530_irq_map,
> + .xlate = irq_domain_xlate_onecell,
> +};
> +
> +static void
> +mt7530_setup_mdio_irq(struct mt7530_priv *priv)
> +{
> + struct dsa_switch *ds = priv->ds;
> + int p;
> +
> + for (p = 0; p < MT7530_NUM_PHYS; p++) {
> + if (BIT(p) & ds->phys_mii_mask) {
> + unsigned int irq;
> +
> + irq = irq_create_mapping(priv->irq_domain, p);
This seems odd. Why aren't the MDIO IRQs allocated on demand as
endpoint attached to this interrupt controller are being probed
individually? In general, doing this allocation upfront is an
indication that there is some missing information in the DT to perform
the discovery.
> + ds->slave_mii_bus->irq[p] = irq;
> + }
> + }
> +}
> +
> +static int
> +mt7530_setup_irq(struct mt7530_priv *priv)
> +{
> + struct device *dev = priv->dev;
> + struct device_node *np = dev->of_node;
> + int ret;
> +
> + if (!of_property_read_bool(np, "interrupt-controller")) {
> + dev_info(dev, "no interrupt support\n");
> + return 0;
> + }
> +
> + priv->irq = of_irq_get(np, 0);
> + if (priv->irq <= 0) {
> + dev_err(dev, "failed to get parent IRQ: %d\n", priv->irq);
> + return priv->irq ? : -EINVAL;
> + }
> +
> + priv->irq_domain = irq_domain_add_linear(np, MT7530_NUM_PHYS,
> + &mt7530_irq_domain_ops, priv);
> + if (!priv->irq_domain) {
> + dev_err(dev, "failed to create IRQ domain\n");
> + return -ENOMEM;
> + }
> +
> + /* This register must be set for MT7530 to properly fire interrupts */
> + if (priv->id != ID_MT7531)
Why not check for ID_MT7530 directly then?
> + mt7530_set(priv, MT7530_TOP_SIG_CTRL, TOP_SIG_CTRL_NORMAL);
> +
> + ret = request_threaded_irq(priv->irq, NULL, mt7530_irq_thread_fn,
> + IRQF_ONESHOT, KBUILD_MODNAME, priv);
> + if (ret) {
> + irq_domain_remove(priv->irq_domain);
> + dev_err(dev, "failed to request IRQ: %d\n", ret);
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static void
> +mt7530_free_mdio_irq(struct mt7530_priv *priv)
> +{
> + int p;
> +
> + for (p = 0; p < MT7530_NUM_PHYS; p++) {
> + if (BIT(p) & priv->ds->phys_mii_mask) {
> + unsigned int irq;
> +
> + irq = irq_find_mapping(priv->irq_domain, p);
> + irq_dispose_mapping(irq);
> + }
> + }
> +}
> +
> +
> +static void
> +mt7530_free_irq_common(struct mt7530_priv *priv)
> +{
> + free_irq(priv->irq, priv);
> + irq_domain_remove(priv->irq_domain);
> +}
> +
> +static void
> +mt7530_free_irq(struct mt7530_priv *priv)
> +{
> + mt7530_free_mdio_irq(priv);
> + mt7530_free_irq_common(priv);
> +}
> +
> +static int
> +mt7530_setup_mdio(struct mt7530_priv *priv)
> +{
> + struct dsa_switch *ds = priv->ds;
> + struct device *dev = priv->dev;
> + struct mii_bus *bus;
> + static int idx;
> + int ret;
> +
> + bus = devm_mdiobus_alloc(dev);
> + if (!bus)
> + return -ENOMEM;
> +
> + ds->slave_mii_bus = bus;
> + bus->priv = priv;
> + bus->name = KBUILD_MODNAME "-mii";
> + snprintf(bus->id, MII_BUS_ID_SIZE, KBUILD_MODNAME "-%d", idx++);
> + bus->read = mt753x_phy_read;
> + bus->write = mt753x_phy_write;
> + bus->parent = dev;
> + bus->phy_mask = ~ds->phys_mii_mask;
> +
> + if (priv->irq)
> + mt7530_setup_mdio_irq(priv);
> +
> + ret = mdiobus_register(bus);
> + if (ret) {
> + dev_err(dev, "failed to register MDIO bus: %d\n", ret);
> + if (priv->irq)
> + mt7530_free_mdio_irq(priv);
> + }
> +
> + return ret;
> +}
> +
> static int
> mt7530_setup(struct dsa_switch *ds)
> {
> @@ -2780,32 +2996,25 @@ static int
> mt753x_setup(struct dsa_switch *ds)
> {
> struct mt7530_priv *priv = ds->priv;
> + int ret = priv->info->sw_setup(ds);
> + if (ret)
> + return ret;
>
> - return priv->info->sw_setup(ds);
> -}
> -
> -static int
> -mt753x_phy_read(struct dsa_switch *ds, int port, int regnum)
> -{
> - struct mt7530_priv *priv = ds->priv;
> -
> - return priv->info->phy_read(ds, port, regnum);
> -}
> + ret = mt7530_setup_irq(priv);
> + if (ret)
> + return ret;
>
> -static int
> -mt753x_phy_write(struct dsa_switch *ds, int port, int regnum, u16 val)
> -{
> - struct mt7530_priv *priv = ds->priv;
> + ret = mt7530_setup_mdio(priv);
> + if (ret && priv->irq)
> + mt7530_free_irq_common(priv);
>
> - return priv->info->phy_write(ds, port, regnum, val);
> + return ret;
> }
>
> static const struct dsa_switch_ops mt7530_switch_ops = {
> .get_tag_protocol = mtk_get_tag_protocol,
> .setup = mt753x_setup,
> .get_strings = mt7530_get_strings,
> - .phy_read = mt753x_phy_read,
> - .phy_write = mt753x_phy_write,
I don't get why this change is part of the interrupt support. This
should probably be a separate patch.
> .get_ethtool_stats = mt7530_get_ethtool_stats,
> .get_sset_count = mt7530_get_sset_count,
> .set_ageing_time = mt7530_set_ageing_time,
> @@ -2986,6 +3195,9 @@ mt7530_remove(struct mdio_device *mdiodev)
> dev_err(priv->dev, "Failed to disable io pwr: %d\n",
> ret);
>
> + if (priv->irq)
> + mt7530_free_irq(priv);
> +
> dsa_unregister_switch(priv->ds);
> mutex_destroy(&priv->reg_mutex);
> }
> diff --git a/drivers/net/dsa/mt7530.h b/drivers/net/dsa/mt7530.h
> index ec36ea5dfd57..62fcaabefba1 100644
> --- a/drivers/net/dsa/mt7530.h
> +++ b/drivers/net/dsa/mt7530.h
nit: Another thing is that I don't see why this include file exists at
all. The only user is mt7530.c, so the two could be merged and reduce
the clutter.
Thanks,
M.
--
Without deviation from the norm, progress is not possible.
More information about the Linux-mediatek
mailing list