[PATCH v2 2/4] remoteproc: Add a remoteproc driver for the MT8183's APU
Alexandre Bailon
abailon at baylibre.com
Thu Sep 10 09:01:46 EDT 2020
This adds a driver to control the APU present in the MT8183.
This loads the firmware and start the DSP.
Signed-off-by: Alexandre Bailon <abailon at baylibre.com>
---
drivers/remoteproc/Kconfig | 10 ++
drivers/remoteproc/Makefile | 1 +
drivers/remoteproc/mtk_apu.c | 288 +++++++++++++++++++++++++++++++++++
3 files changed, 299 insertions(+)
create mode 100644 drivers/remoteproc/mtk_apu.c
diff --git a/drivers/remoteproc/Kconfig b/drivers/remoteproc/Kconfig
index c6659dfea7c7..4ebea57bf4c8 100644
--- a/drivers/remoteproc/Kconfig
+++ b/drivers/remoteproc/Kconfig
@@ -51,6 +51,16 @@ config MTK_SCP
It's safe to say N here.
+config MTK_APU
+ tristate "Mediatek APU remoteproc support"
+ depends on ARCH_MEDIATEK
+ depends on MTK_IOMMU
+ help
+ Say y to support the Mediatek's Accelerated Processing Unit (APU) via
+ the remote processor framework.
+
+ It's safe to say N here.
+
config OMAP_REMOTEPROC
tristate "OMAP remoteproc support"
depends on ARCH_OMAP4 || SOC_OMAP5 || SOC_DRA7XX
diff --git a/drivers/remoteproc/Makefile b/drivers/remoteproc/Makefile
index 3dfa28e6c701..174644f38fda 100644
--- a/drivers/remoteproc/Makefile
+++ b/drivers/remoteproc/Makefile
@@ -14,6 +14,7 @@ obj-$(CONFIG_REMOTEPROC_CDEV) += remoteproc_cdev.o
obj-$(CONFIG_IMX_REMOTEPROC) += imx_rproc.o
obj-$(CONFIG_INGENIC_VPU_RPROC) += ingenic_rproc.o
obj-$(CONFIG_MTK_SCP) += mtk_scp.o mtk_scp_ipi.o
+obj-$(CONFIG_MTK_APU) += mtk_apu.o
obj-$(CONFIG_OMAP_REMOTEPROC) += omap_remoteproc.o
obj-$(CONFIG_WKUP_M3_RPROC) += wkup_m3_rproc.o
obj-$(CONFIG_DA8XX_REMOTEPROC) += da8xx_remoteproc.o
diff --git a/drivers/remoteproc/mtk_apu.c b/drivers/remoteproc/mtk_apu.c
new file mode 100644
index 000000000000..6d2f577cfde5
--- /dev/null
+++ b/drivers/remoteproc/mtk_apu.c
@@ -0,0 +1,288 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 BayLibre SAS
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/highmem.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iommu.h>
+#include <linux/irq.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_reserved_mem.h>
+#include <linux/platform_device.h>
+#include <linux/remoteproc.h>
+
+#include "remoteproc_internal.h"
+
+/* From MT8183 4.5 Vision Processor Unit (VPU).pdf datasheet */
+#define SW_RST (0x0000000C)
+#define SW_RST_OCD_HALT_ON_RST BIT(12)
+#define SW_RST_IPU_D_RST BIT(8)
+#define SW_RST_IPU_B_RST BIT(4)
+#define CORE_CTRL (0x00000110)
+#define CORE_CTRL_PDEBUG_ENABLE BIT(31)
+#define CORE_CTRL_SRAM_64K_iMEM (0x00 << 27)
+#define CORE_CTRL_SRAM_96K_iMEM (0x01 << 27)
+#define CORE_CTRL_SRAM_128K_iMEM (0x02 << 27)
+#define CORE_CTRL_SRAM_192K_iMEM (0x03 << 27)
+#define CORE_CTRL_SRAM_256K_iMEM (0x04 << 27)
+#define CORE_CTRL_PBCLK_ENABLE BIT(26)
+#define CORE_CTRL_RUN_STALL BIT(23)
+#define CORE_CTRL_STATE_VECTOR_SELECT BIT(19)
+#define CORE_CTRL_PIF_GATED BIT(17)
+#define CORE_CTRL_NMI BIT(0)
+#define CORE_XTENSA_INT (0x00000114)
+#define CORE_CTL_XTENSA_INT (0x00000118)
+#define CORE_DEFAULT0 (0x0000013C)
+#define CORE_DEFAULT0_QOS_SWAP_0 (0x00 << 28)
+#define CORE_DEFAULT0_QOS_SWAP_1 (0x01 << 28)
+#define CORE_DEFAULT0_QOS_SWAP_2 (0x02 << 28)
+#define CORE_DEFAULT0_QOS_SWAP_3 (0x03 << 28)
+#define CORE_DEFAULT0_ARUSER_USE_IOMMU (0x10 << 23)
+#define CORE_DEFAULT0_AWUSER_USE_IOMMU (0x10 << 18)
+#define CORE_DEFAULT1 (0x00000140)
+#define CORE_DEFAULT0_ARUSER_IDMA_USE_IOMMU (0x10 << 0)
+#define CORE_DEFAULT0_AWUSER_IDMA_USE_IOMMU (0x10 << 5)
+#define CORE_XTENSA_ALTRESETVEC (0x000001F8)
+
+struct mtk_apu_rproc {
+ struct device *dev;
+ struct rproc *rproc;
+
+ void __iomem *base;
+ int irq;
+ struct clk_bulk_data clks[3];
+};
+
+static int mtk_apu_rproc_prepare(struct rproc *rproc)
+{
+ struct mtk_apu_rproc *apu_rproc = rproc->priv;
+ int ret;
+
+ ret = clk_bulk_prepare_enable(ARRAY_SIZE(apu_rproc->clks),
+ apu_rproc->clks);
+ if (ret)
+ dev_err(apu_rproc->dev, "Failed to enable clocks\n");
+
+ return ret;
+}
+
+static int mtk_apu_rproc_unprepare(struct rproc *rproc)
+{
+ struct mtk_apu_rproc *apu_rproc = rproc->priv;
+
+ clk_bulk_disable_unprepare(ARRAY_SIZE(apu_rproc->clks),
+ apu_rproc->clks);
+
+ return 0;
+}
+
+static int mtk_apu_rproc_start(struct rproc *rproc)
+{
+ struct mtk_apu_rproc *apu_rproc = rproc->priv;
+ u32 core_ctrl;
+
+ /* Set reset vector of APU firmware boot address */
+ writel(rproc->bootaddr, apu_rproc->base + CORE_XTENSA_ALTRESETVEC);
+
+ /* Turn on the clocks and stall the APU */
+ core_ctrl = readl(apu_rproc->base + CORE_CTRL);
+ core_ctrl |= CORE_CTRL_PDEBUG_ENABLE | CORE_CTRL_PBCLK_ENABLE |
+ CORE_CTRL_STATE_VECTOR_SELECT | CORE_CTRL_RUN_STALL |
+ CORE_CTRL_PIF_GATED;
+ writel(core_ctrl, apu_rproc->base + CORE_CTRL);
+
+ /* Reset the APU */
+ writel(SW_RST_OCD_HALT_ON_RST | SW_RST_IPU_B_RST | SW_RST_IPU_D_RST,
+ apu_rproc->base + SW_RST);
+ ndelay(27);
+ writel(0, apu_rproc->base + SW_RST);
+
+ core_ctrl &= ~CORE_CTRL_PIF_GATED;
+ writel(core_ctrl, apu_rproc->base + CORE_CTRL);
+
+ /* Configure memory accesses to go through the IOMMU */
+ writel(CORE_DEFAULT0_AWUSER_USE_IOMMU | CORE_DEFAULT0_ARUSER_USE_IOMMU |
+ CORE_DEFAULT0_QOS_SWAP_1, apu_rproc->base + CORE_DEFAULT0);
+ writel(CORE_DEFAULT0_AWUSER_IDMA_USE_IOMMU |
+ CORE_DEFAULT0_ARUSER_IDMA_USE_IOMMU,
+ apu_rproc->base + CORE_DEFAULT1);
+
+ /* Release the APU */
+ core_ctrl &= ~CORE_CTRL_RUN_STALL;
+ writel(core_ctrl, apu_rproc->base + CORE_CTRL);
+
+ return 0;
+}
+
+static int mtk_apu_rproc_stop(struct rproc *rproc)
+{
+ struct mtk_apu_rproc *apu_rproc = rproc->priv;
+ u32 core_ctrl;
+
+ core_ctrl = readl(apu_rproc->base + CORE_CTRL);
+ writel(core_ctrl | CORE_CTRL_RUN_STALL, apu_rproc->base + CORE_CTRL);
+
+ return 0;
+}
+
+static void mtk_apu_rproc_kick(struct rproc *rproc, int vqid)
+{
+ struct mtk_apu_rproc *apu_rproc = rproc->priv;
+
+ writel(1 << vqid, apu_rproc->base + CORE_CTL_XTENSA_INT);
+}
+
+static const struct rproc_ops mtk_apu_rproc_ops = {
+ .prepare = mtk_apu_rproc_prepare,
+ .unprepare = mtk_apu_rproc_unprepare,
+ .start = mtk_apu_rproc_start,
+ .stop = mtk_apu_rproc_stop,
+ .kick = mtk_apu_rproc_kick,
+};
+
+static irqreturn_t mtk_apu_rproc_callback(int irq, void *data)
+{
+ struct rproc *rproc = data;
+ struct mtk_apu_rproc *apu_rproc = (struct mtk_apu_rproc *)rproc->priv;
+
+ writel(1, apu_rproc->base + CORE_XTENSA_INT);
+
+ return IRQ_WAKE_THREAD;
+}
+
+static irqreturn_t handle_event(int irq, void *data)
+{
+ struct rproc *rproc = data;
+
+ rproc_vq_interrupt(rproc, 0);
+ rproc_vq_interrupt(rproc, 1);
+
+ return IRQ_HANDLED;
+}
+
+static int mtk_apu_rproc_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct mtk_apu_rproc *apu_rproc;
+ struct rproc *rproc;
+ struct resource *res;
+ int ret;
+
+ rproc = rproc_alloc(dev, dev_name(dev), &mtk_apu_rproc_ops, NULL,
+ sizeof(*apu_rproc));
+ if (!rproc)
+ return -ENOMEM;
+
+ rproc->recovery_disabled = true;
+ rproc->has_iommu = false;
+
+ apu_rproc = rproc->priv;
+ apu_rproc->rproc = rproc;
+ apu_rproc->dev = dev;
+
+ platform_set_drvdata(pdev, rproc);
+
+ rproc->domain = iommu_get_domain_for_dev(dev);
+ if (!rproc->domain) {
+ dev_err(dev, "Failed to get the IOMMU domain\n");
+ ret = -EINVAL;
+ goto free_rproc;
+ }
+
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ apu_rproc->base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(apu_rproc->base)) {
+ dev_err(dev, "Failed to map mmio\n");
+ ret = PTR_ERR(apu_rproc->base);
+ goto free_rproc;
+ }
+
+ apu_rproc->irq = platform_get_irq(pdev, 0);
+ if (apu_rproc->irq < 0) {
+ ret = apu_rproc->irq;
+ goto free_rproc;
+ }
+
+ ret = devm_request_threaded_irq(dev, apu_rproc->irq,
+ mtk_apu_rproc_callback, handle_event,
+ IRQF_SHARED | IRQF_ONESHOT,
+ NULL, rproc);
+ if (ret) {
+ dev_err(dev, "devm_request_threaded_irq error: %d\n", ret);
+ goto free_rproc;
+ }
+
+ apu_rproc->clks[0].id = "ipu";
+ apu_rproc->clks[1].id = "axi";
+ apu_rproc->clks[1].id = "jtag";
+
+ ret = devm_clk_bulk_get(dev, ARRAY_SIZE(apu_rproc->clks),
+ apu_rproc->clks);
+ if (ret) {
+ dev_err(dev, "Failed to get clocks\n");
+ goto free_rproc;
+ }
+
+ ret = of_reserved_mem_device_init(dev);
+ if (ret) {
+ dev_err(dev, "device does not have specific CMA pool\n");
+ goto free_rproc;
+ }
+
+ ret = rproc_add(rproc);
+ if (ret) {
+ dev_err(dev, "rproc_add failed: %d\n", ret);
+ goto free_mem;
+ }
+
+ return 0;
+
+free_mem:
+ of_reserved_mem_device_release(dev);
+free_rproc:
+ rproc_free(rproc);
+
+ return ret;
+}
+
+static int mtk_apu_rproc_remove(struct platform_device *pdev)
+{
+ struct rproc *rproc = platform_get_drvdata(pdev);
+ struct mtk_apu_rproc *apu_rproc = (struct mtk_apu_rproc *)rproc->priv;
+ struct device *dev = &pdev->dev;
+
+ disable_irq(apu_rproc->irq);
+
+ rproc_del(rproc);
+ of_reserved_mem_device_release(dev);
+ rproc_free(rproc);
+
+ return 0;
+}
+
+static const struct of_device_id mtk_apu_rproc_of_match[] = {
+ { .compatible = "mediatek,mt8183-apu", },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, mtk_apu_rproc_of_match);
+
+static struct platform_driver mtk_apu_rproc_driver = {
+ .probe = mtk_apu_rproc_probe,
+ .remove = mtk_apu_rproc_remove,
+ .driver = {
+ .name = "mtk_apu-rproc",
+ .of_match_table = of_match_ptr(mtk_apu_rproc_of_match),
+ },
+};
+module_platform_driver(mtk_apu_rproc_driver);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Alexandre Bailon");
+MODULE_DESCRIPTION("MTK APU Remote Processor control driver");
--
2.26.2
More information about the Linux-mediatek
mailing list