[PATCH v3 2/2] spmi: mediatek: Add support for MT6873/8192
Stephen Boyd
sboyd at kernel.org
Fri Nov 13 03:46:32 EST 2020
Quoting Hsin-Hsiung Wang (2020-10-15 05:59:08)
> add spmi support for MT6873/8192.
Capitalize Add please.
>
> Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang at mediatek.com>
> ---
> drivers/spmi/Kconfig | 9 +
> drivers/spmi/Makefile | 1 +
> drivers/spmi/spmi-mtk-pmif.c | 474 +++++++++++++++++++++++++++++++++++
> 3 files changed, 484 insertions(+)
> create mode 100644 drivers/spmi/spmi-mtk-pmif.c
>
> diff --git a/drivers/spmi/spmi-mtk-pmif.c b/drivers/spmi/spmi-mtk-pmif.c
> new file mode 100644
> index 000000000000..ac71e64a2bda
> --- /dev/null
> +++ b/drivers/spmi/spmi-mtk-pmif.c
> @@ -0,0 +1,474 @@
> +// SPDX-License-Identifier: GPL-2.0
> +//
> +// Copyright (c) 2020 MediaTek Inc.
> +
> +#include <linux/clk.h>
> +#include <linux/iopoll.h>
> +#include <linux/module.h>
> +#include <linux/of_address.h>
Is this include used?
> +#include <linux/of_device.h>
> +#include <linux/spmi.h>
> +
> +#define SWINF_IDLE 0x00
> +#define SWINF_WFVLDCLR 0x06
> +
> +#define GET_SWINF(x) (((x) >> 1) & 0x7)
> +
> +#define PMIF_CMD_REG_0 0
> +#define PMIF_CMD_REG 1
> +#define PMIF_CMD_EXT_REG 2
> +#define PMIF_CMD_EXT_REG_LONG 3
> +
> +#define PMIF_DELAY_US 10
> +#define PMIF_TIMEOUT (10 * 1000)
> +
> +#define PMIF_CHAN_OFFSET 0x5
> +
> +#define SPMI_OP_ST_BUSY 1
> +
> +struct ch_reg {
> + u32 ch_sta;
> + u32 wdata;
> + u32 rdata;
> + u32 ch_send;
> + u32 ch_rdy;
> +};
> +
> +struct pmif {
> + void __iomem *base;
> + const u32 *regs;
> + void __iomem *spmimst_base;
> + const u32 *spmimst_regs;
> + u32 soc_chan;
> + int grpid;
> + raw_spinlock_t lock;
> + struct clk *pmif_sys_ck;
> + struct clk *pmif_tmr_ck;
These two are acquired but never used?
> + struct clk *spmimst_clk_mux;
> + struct ch_reg chan;
> +};
> +
> +enum pmif_regs {
> + PMIF_INIT_DONE,
> + PMIF_INF_EN,
> + PMIF_ARB_EN,
> + PMIF_CMDISSUE_EN,
> + PMIF_TIMER_CTRL,
> + PMIF_SPI_MODE_CTRL,
> + PMIF_IRQ_EVENT_EN_0,
> + PMIF_IRQ_FLAG_0,
> + PMIF_IRQ_CLR_0,
> + PMIF_IRQ_EVENT_EN_1,
> + PMIF_IRQ_FLAG_1,
> + PMIF_IRQ_CLR_1,
> + PMIF_IRQ_EVENT_EN_2,
> + PMIF_IRQ_FLAG_2,
> + PMIF_IRQ_CLR_2,
> + PMIF_IRQ_EVENT_EN_3,
> + PMIF_IRQ_FLAG_3,
> + PMIF_IRQ_CLR_3,
> + PMIF_IRQ_EVENT_EN_4,
> + PMIF_IRQ_FLAG_4,
> + PMIF_IRQ_CLR_4,
> + PMIF_WDT_EVENT_EN_0,
> + PMIF_WDT_FLAG_0,
> + PMIF_WDT_EVENT_EN_1,
> + PMIF_WDT_FLAG_1,
> + PMIF_SWINF_0_STA,
> + PMIF_SWINF_0_WDATA_31_0,
> + PMIF_SWINF_0_RDATA_31_0,
> + PMIF_SWINF_0_ACC,
> + PMIF_SWINF_0_VLD_CLR,
> + PMIF_SWINF_1_STA,
> + PMIF_SWINF_1_WDATA_31_0,
> + PMIF_SWINF_1_RDATA_31_0,
> + PMIF_SWINF_1_ACC,
> + PMIF_SWINF_1_VLD_CLR,
> + PMIF_SWINF_2_STA,
> + PMIF_SWINF_2_WDATA_31_0,
> + PMIF_SWINF_2_RDATA_31_0,
> + PMIF_SWINF_2_ACC,
> + PMIF_SWINF_2_VLD_CLR,
> + PMIF_SWINF_3_STA,
> + PMIF_SWINF_3_WDATA_31_0,
> + PMIF_SWINF_3_RDATA_31_0,
> + PMIF_SWINF_3_ACC,
> + PMIF_SWINF_3_VLD_CLR,
> +};
> +
> +static const u32 mt6873_regs[] = {
> + [PMIF_INIT_DONE] = 0x0000,
> + [PMIF_INF_EN] = 0x0024,
> + [PMIF_ARB_EN] = 0x0150,
> + [PMIF_CMDISSUE_EN] = 0x03B4,
> + [PMIF_TIMER_CTRL] = 0x03E0,
> + [PMIF_SPI_MODE_CTRL] = 0x0400,
> + [PMIF_IRQ_EVENT_EN_0] = 0x0418,
> + [PMIF_IRQ_FLAG_0] = 0x0420,
> + [PMIF_IRQ_CLR_0] = 0x0424,
> + [PMIF_IRQ_EVENT_EN_1] = 0x0428,
> + [PMIF_IRQ_FLAG_1] = 0x0430,
> + [PMIF_IRQ_CLR_1] = 0x0434,
> + [PMIF_IRQ_EVENT_EN_2] = 0x0438,
> + [PMIF_IRQ_FLAG_2] = 0x0440,
> + [PMIF_IRQ_CLR_2] = 0x0444,
> + [PMIF_IRQ_EVENT_EN_3] = 0x0448,
> + [PMIF_IRQ_FLAG_3] = 0x0450,
> + [PMIF_IRQ_CLR_3] = 0x0454,
> + [PMIF_IRQ_EVENT_EN_4] = 0x0458,
> + [PMIF_IRQ_FLAG_4] = 0x0460,
> + [PMIF_IRQ_CLR_4] = 0x0464,
> + [PMIF_WDT_EVENT_EN_0] = 0x046C,
> + [PMIF_WDT_FLAG_0] = 0x0470,
> + [PMIF_WDT_EVENT_EN_1] = 0x0474,
> + [PMIF_WDT_FLAG_1] = 0x0478,
> + [PMIF_SWINF_0_ACC] = 0x0C00,
> + [PMIF_SWINF_0_WDATA_31_0] = 0x0C04,
> + [PMIF_SWINF_0_RDATA_31_0] = 0x0C14,
> + [PMIF_SWINF_0_VLD_CLR] = 0x0C24,
> + [PMIF_SWINF_0_STA] = 0x0C28,
> + [PMIF_SWINF_1_ACC] = 0x0C40,
> + [PMIF_SWINF_1_WDATA_31_0] = 0x0C44,
> + [PMIF_SWINF_1_RDATA_31_0] = 0x0C54,
> + [PMIF_SWINF_1_VLD_CLR] = 0x0C64,
> + [PMIF_SWINF_1_STA] = 0x0C68,
> + [PMIF_SWINF_2_ACC] = 0x0C80,
> + [PMIF_SWINF_2_WDATA_31_0] = 0x0C84,
> + [PMIF_SWINF_2_RDATA_31_0] = 0x0C94,
> + [PMIF_SWINF_2_VLD_CLR] = 0x0CA4,
> + [PMIF_SWINF_2_STA] = 0x0CA8,
> + [PMIF_SWINF_3_ACC] = 0x0CC0,
> + [PMIF_SWINF_3_WDATA_31_0] = 0x0CC4,
> + [PMIF_SWINF_3_RDATA_31_0] = 0x0CD4,
> + [PMIF_SWINF_3_VLD_CLR] = 0x0CE4,
> + [PMIF_SWINF_3_STA] = 0x0CE8,
> +};
> +
> +enum spmi_regs {
> + SPMI_OP_ST_CTRL,
> + SPMI_GRP_ID_EN,
> + SPMI_OP_ST_STA,
> + SPMI_MST_SAMPL,
> + SPMI_MST_REQ_EN,
> + SPMI_REC_CTRL,
> + SPMI_REC0,
> + SPMI_REC1,
> + SPMI_REC2,
> + SPMI_REC3,
> + SPMI_REC4,
> + SPMI_MST_DBG,
> +};
> +
> +static const u32 mt6873_spmi_regs[] = {
> + [SPMI_OP_ST_CTRL] = 0x0000,
> + [SPMI_GRP_ID_EN] = 0x0004,
> + [SPMI_OP_ST_STA] = 0x0008,
> + [SPMI_MST_SAMPL] = 0x000c,
> + [SPMI_MST_REQ_EN] = 0x0010,
> + [SPMI_REC_CTRL] = 0x0040,
> + [SPMI_REC0] = 0x0044,
> + [SPMI_REC1] = 0x0048,
> + [SPMI_REC2] = 0x004c,
> + [SPMI_REC3] = 0x0050,
> + [SPMI_REC4] = 0x0054,
> + [SPMI_MST_DBG] = 0x00fc,
> +};
> +
> +static u32 pmif_readl(struct pmif *arb, enum pmif_regs reg)
> +{
> + return readl(arb->base + arb->regs[reg]);
> +}
> +
> +static void pmif_writel(struct pmif *arb, u32 val, enum pmif_regs reg)
> +{
> + writel(val, arb->base + arb->regs[reg]);
> +}
> +
> +static void mtk_spmi_writel(struct pmif *arb, u32 val, enum spmi_regs reg)
> +{
> + writel(val, arb->spmimst_base + arb->spmimst_regs[reg]);
> +}
> +
> +static bool pmif_is_fsm_vldclr(struct pmif *arb)
> +{
> + u32 reg_rdata;
> +
> + reg_rdata = pmif_readl(arb, arb->chan.ch_sta);
> + return GET_SWINF(reg_rdata) == SWINF_WFVLDCLR;
> +}
> +
> +static int pmif_arb_cmd(struct spmi_controller *ctrl, u8 opc, u8 sid)
> +{
> + struct pmif *arb = spmi_controller_get_drvdata(ctrl);
> + u32 rdata;
> + u8 cmd;
Any reason to not just use a u32?
> + int ret;
> +
> + /* Check the opcode */
> + if (opc == SPMI_CMD_RESET)
> + cmd = 0;
> + else if (opc == SPMI_CMD_SLEEP)
> + cmd = 1;
> + else if (opc == SPMI_CMD_SHUTDOWN)
> + cmd = 2;
> + else if (opc == SPMI_CMD_WAKEUP)
> + cmd = 3;
> + else
> + return -EINVAL;
> +
> + mtk_spmi_writel(arb, (cmd << 0x4) | sid, SPMI_OP_ST_CTRL);
Then this shift isn't concerning with regards to overflow.
> + ret = readl_poll_timeout_atomic(arb->spmimst_base + arb->spmimst_regs[SPMI_OP_ST_STA],
> + rdata, (rdata & SPMI_OP_ST_BUSY) == SPMI_OP_ST_BUSY,
> + PMIF_DELAY_US, PMIF_TIMEOUT);
> + if (ret < 0)
> + dev_err(&ctrl->dev, "timeout, err = %d\r\n", ret);
Remove the \r.
> +
> + return ret;
> +}
> +
> +static int pmif_spmi_read_cmd(struct spmi_controller *ctrl, u8 opc, u8 sid,
> + u16 addr, u8 *buf, size_t len)
> +{
> + struct pmif *arb = spmi_controller_get_drvdata(ctrl);
> + struct ch_reg *inf_reg = NULL;
Please drop assignment.
> + int ret;
> + u32 data = 0;
Please drop assignment.
> + u8 bc = len - 1;
Can this overflow?
> + unsigned long flags;
> +
> + /* Check for argument validation. */
> + if (sid & ~(0xf))
> + return -EINVAL;
> +
> + if (!arb)
Is this possible?
> + return -EINVAL;
> +
> + inf_reg = &arb->chan;
> + /* Check the opcode */
Please remove useless comment.
> + if (opc >= 0x60 && opc <= 0x7f)
> + opc = PMIF_CMD_REG;
> + else if (opc >= 0x20 && opc <= 0x2f)
> + opc = PMIF_CMD_EXT_REG_LONG;
> + else if (opc >= 0x38 && opc <= 0x3f)
> + opc = PMIF_CMD_EXT_REG_LONG;
> + else
> + return -EINVAL;
> +
> + raw_spin_lock_irqsave(&arb->lock, flags);
> + /* Wait for Software Interface FSM state to be IDLE. */
> + ret = readl_poll_timeout_atomic(arb->base + arb->regs[inf_reg->ch_sta],
> + data, GET_SWINF(data) == SWINF_IDLE,
> + PMIF_DELAY_US, PMIF_TIMEOUT);
> + if (ret < 0) {
> + /* set channel ready if the data has transferred */
> + if (pmif_is_fsm_vldclr(arb))
> + pmif_writel(arb, 1, inf_reg->ch_rdy);
> + raw_spin_unlock_irqrestore(&arb->lock, flags);
> + return ret;
Please goto spin unlock and return ret instead of duplicating it.
> + }
> +
> + /* Send the command. */
> + pmif_writel(arb,
> + (opc << 30) | (sid << 24) | (bc << 16) | addr,
Please pack the u32 into a local variable so this fits on one line.
> + inf_reg->ch_send);
> +
> + /* Wait for Software Interface FSM state to be WFVLDCLR,
Please fix kernel comment style, /* is on its own line.
> + *
> + * read the data and clear the valid flag.
> + */
> + ret = readl_poll_timeout_atomic(arb->base + arb->regs[inf_reg->ch_sta],
> + data, GET_SWINF(data) == SWINF_WFVLDCLR,
> + PMIF_DELAY_US, PMIF_TIMEOUT);
> + if (ret < 0) {
goto out;
> + raw_spin_unlock_irqrestore(&arb->lock, flags);
> + return ret;
> + }
> +
> + data = pmif_readl(arb, inf_reg->rdata);
> + memcpy(buf, &data, (bc & 3) + 1);
Why is it aligned memcpy?
> + pmif_writel(arb, 1, inf_reg->ch_rdy);
out:
> + raw_spin_unlock_irqrestore(&arb->lock, flags);
> +
> + return 0;
return ret;
> +}
> +
> +static int pmif_spmi_write_cmd(struct spmi_controller *ctrl, u8 opc, u8 sid,
> + u16 addr, const u8 *buf, size_t len)
> +{
> + struct pmif *arb = spmi_controller_get_drvdata(ctrl);
> + struct ch_reg *inf_reg = NULL;
> + int ret;
> + u32 data = 0;
> + u8 bc = len - 1;
> + unsigned long flags = 0;
> +
> + /* Check for argument validation. */
> + if (sid & ~(0xf))
> + return -EINVAL;
> +
> + if (!arb)
> + return -EINVAL;
> +
> + inf_reg = &arb->chan;
> +
> + /* Check the opcode */
> + if (opc >= 0x40 && opc <= 0x5F)
> + opc = PMIF_CMD_REG;
> + else if (opc <= 0x0F)
> + opc = PMIF_CMD_EXT_REG_LONG;
> + else if (opc >= 0x30 && opc <= 0x37)
> + opc = PMIF_CMD_EXT_REG_LONG;
> + else if (opc >= 0x80)
> + opc = PMIF_CMD_REG_0;
> + else
> + return -EINVAL;
> +
> + raw_spin_lock_irqsave(&arb->lock, flags);
> + /* Wait for Software Interface FSM state to be IDLE. */
> + ret = readl_poll_timeout_atomic(arb->base + arb->regs[inf_reg->ch_sta],
> + data, GET_SWINF(data) == SWINF_IDLE,
> + PMIF_DELAY_US, PMIF_TIMEOUT);
> + if (ret < 0) {
> + /* set channel ready if the data has transferred */
> + if (pmif_is_fsm_vldclr(arb))
> + pmif_writel(arb, 1, inf_reg->ch_rdy);
> + raw_spin_unlock_irqrestore(&arb->lock, flags);
> + return ret;
> + }
> +
> + /* Set the write data. */
> + memcpy(&data, buf, (bc & 3) + 1);
> + pmif_writel(arb, data, inf_reg->wdata);
> +
> + /* Send the command. */
> + pmif_writel(arb,
> + (opc << 30) | BIT(29) | (sid << 24) | (bc << 16) | addr,
> + inf_reg->ch_send);
> + raw_spin_unlock_irqrestore(&arb->lock, flags);
A lot of the same comments apply.
> +
> + return 0;
> +}
> +
> +static struct pmif mt6873_pmif_arb[] = {
Is this a singleton?
> + {
> + .regs = mt6873_regs,
> + .spmimst_regs = mt6873_spmi_regs,
> + .soc_chan = 2,
> + },
> +};
> +
> +static int mtk_spmi_probe(struct platform_device *pdev)
> +{
> + struct pmif *arb;
> + struct resource *res;
> + struct spmi_controller *ctrl;
> + int err = 0;
Is this assignment necessary?
> +
> + ctrl = spmi_controller_alloc(&pdev->dev, sizeof(*arb));
> + if (!ctrl)
> + return -ENOMEM;
> +
> + ctrl->cmd = pmif_arb_cmd;
> + ctrl->read_cmd = pmif_spmi_read_cmd;
> + ctrl->write_cmd = pmif_spmi_write_cmd;
> +
> + /* re-assign of_id->data */
> + spmi_controller_set_drvdata(ctrl, (void *)of_device_get_match_data(&pdev->dev));
Please drop cast to void *.
> + arb = spmi_controller_get_drvdata(ctrl);
> +
> + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "pmif");
> + arb->base = devm_ioremap_resource(&pdev->dev, res);
Preferably use devm_platform_ioremap_resource(pdev, index).
> + if (IS_ERR(arb->base)) {
> + err = PTR_ERR(arb->base);
> + goto err_put_ctrl;
> + }
> +
> + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "spmimst");
> + arb->spmimst_base = devm_ioremap_resource(&pdev->dev, res);
Same.
> + if (IS_ERR(arb->spmimst_base)) {
> + err = PTR_ERR(arb->spmimst_base);
> + goto err_put_ctrl;
> + }
> +
> + arb->pmif_sys_ck = devm_clk_get(&pdev->dev, "pmif_sys_ck");
> + if (IS_ERR(arb->pmif_sys_ck)) {
> + dev_err(&pdev->dev, "[PMIF]:failed to get ap clock: %ld\n",
Move [PMIF] to pr_fmt?
> + PTR_ERR(arb->pmif_sys_ck));
> + goto err_put_ctrl;
> + }
> +
> + arb->pmif_tmr_ck = devm_clk_get(&pdev->dev, "pmif_tmr_ck");
> + if (IS_ERR(arb->pmif_tmr_ck)) {
> + dev_err(&pdev->dev, "[PMIF]:failed to get tmr clock: %ld\n",
> + PTR_ERR(arb->pmif_tmr_ck));
> + goto err_put_ctrl;
> + }
> +
> + arb->spmimst_clk_mux = devm_clk_get(&pdev->dev, "spmimst_clk_mux");
> + if (IS_ERR(arb->spmimst_clk_mux)) {
> + dev_err(&pdev->dev, "[SPMIMST]:failed to get clock: %ld\n",
> + PTR_ERR(arb->spmimst_clk_mux));
> + goto err_put_ctrl;
> + }
> +
> + err = clk_prepare_enable(arb->spmimst_clk_mux);
> + if (err) {
> + dev_err(&pdev->dev, "[PMIF]:failed to enable spmi master clk.\n");
> + goto err_put_ctrl;
> + }
> +
> + arb->chan.ch_sta = PMIF_SWINF_0_STA + (PMIF_CHAN_OFFSET * arb->soc_chan);
> + arb->chan.wdata = PMIF_SWINF_0_WDATA_31_0 + (PMIF_CHAN_OFFSET * arb->soc_chan);
> + arb->chan.rdata = PMIF_SWINF_0_RDATA_31_0 + (PMIF_CHAN_OFFSET * arb->soc_chan);
> + arb->chan.ch_send = PMIF_SWINF_0_ACC + (PMIF_CHAN_OFFSET * arb->soc_chan);
> + arb->chan.ch_rdy = PMIF_SWINF_0_VLD_CLR + (PMIF_CHAN_OFFSET * arb->soc_chan);
> +
> + raw_spin_lock_init(&arb->lock);
> +
Why raw?
> + platform_set_drvdata(pdev, ctrl);
> +
> + err = spmi_controller_add(ctrl);
More information about the Linux-mediatek
mailing list