[PATCH v10 3/7] [v10, 3/7]: soc: mediatek: SVS: introduce MTK SVS engine
Nicolas Boichat
drinkcat at chromium.org
Wed Dec 30 21:10:32 EST 2020
On Sun, Dec 27, 2020 at 6:55 PM Roger Lu <roger.lu at mediatek.com> wrote:
>
> The Smart Voltage Scaling(SVS) engine is a piece of hardware
> which calculats suitable SVS bank voltages to OPP voltage table.
calculates
> Then, DVFS driver could apply those SVS bank voltages to PMIC/Buck
> when receiving OPP_EVENT_ADJUST_VOLTAGE.
>
> Signed-off-by: Roger Lu <roger.lu at mediatek.com>
> ---
> drivers/soc/mediatek/Kconfig | 10 +
> drivers/soc/mediatek/Makefile | 1 +
> drivers/soc/mediatek/mtk-svs.c | 1748 ++++++++++++++++++++++++++++++++
> 3 files changed, 1759 insertions(+)
> create mode 100644 drivers/soc/mediatek/mtk-svs.c
>
> diff --git a/drivers/soc/mediatek/Kconfig b/drivers/soc/mediatek/Kconfig
> index 59a56cd790ec..f33da25f8336 100644
> --- a/drivers/soc/mediatek/Kconfig
> +++ b/drivers/soc/mediatek/Kconfig
> @@ -51,4 +51,14 @@ config MTK_MMSYS
> Say yes here to add support for the MediaTek Multimedia
> Subsystem (MMSYS).
>
> +config MTK_SVS
> + tristate "MediaTek Smart Voltage Scaling(SVS)"
> + depends on MTK_EFUSE && NVMEM
> + help
> + The Smart Voltage Scaling(SVS) engine is a piece of hardware
> + which has several controllers(banks) for calculating suitable
> + voltage to different power domains(CPU/GPU/CCI) according to
> + chip process corner, temperatures and other factors. Then DVFS
> + driver could apply SVS bank voltage to PMIC/Buck.
> +
> endmenu
> diff --git a/drivers/soc/mediatek/Makefile b/drivers/soc/mediatek/Makefile
> index 01f9f873634a..e10f2cd87514 100644
> --- a/drivers/soc/mediatek/Makefile
> +++ b/drivers/soc/mediatek/Makefile
> @@ -4,3 +4,4 @@ obj-$(CONFIG_MTK_INFRACFG) += mtk-infracfg.o
> obj-$(CONFIG_MTK_PMIC_WRAP) += mtk-pmic-wrap.o
> obj-$(CONFIG_MTK_SCPSYS) += mtk-scpsys.o
> obj-$(CONFIG_MTK_MMSYS) += mtk-mmsys.o
> +obj-$(CONFIG_MTK_SVS) += mtk-svs.o
> diff --git a/drivers/soc/mediatek/mtk-svs.c b/drivers/soc/mediatek/mtk-svs.c
> new file mode 100644
> index 000000000000..0efefb48839d
> --- /dev/null
> +++ b/drivers/soc/mediatek/mtk-svs.c
> @@ -0,0 +1,1748 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Copyright (C) 2020 MediaTek Inc.
> + */
> +
> +#include <linux/bits.h>
> +#include <linux/clk.h>
> +#include <linux/completion.h>
> +#include <linux/device.h>
> +#include <linux/init.h>
> +#include <linux/interrupt.h>
> +#include <linux/kernel.h>
> +#include <linux/kthread.h>
> +#include <linux/module.h>
> +#include <linux/mutex.h>
> +#include <linux/nvmem-consumer.h>
> +#include <linux/of_address.h>
> +#include <linux/of_irq.h>
> +#include <linux/of_platform.h>
> +#include <linux/platform_device.h>
> +#include <linux/pm_domain.h>
> +#include <linux/pm_opp.h>
> +#include <linux/pm_qos.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/reset.h>
> +#include <linux/slab.h>
> +#include <linux/spinlock.h>
> +#include <linux/thermal.h>
> +
> +/* svs bank 1-line sw id */
> +#define SVSB_CPU_LITTLE BIT(0)
> +#define SVSB_CPU_BIG BIT(1)
> +#define SVSB_CCI BIT(2)
> +#define SVSB_GPU BIT(3)
> +
> +/* svs bank mode support */
> +#define SVSB_MODE_ALL_DISABLE 0
> +#define SVSB_MODE_INIT01 BIT(1)
> +#define SVSB_MODE_INIT02 BIT(2)
> +#define SVSB_MODE_MON BIT(3)
> +
> +/* svs bank init01 condition */
> +#define SVSB_INIT01_VOLT_IGNORE BIT(1)
> +#define SVSB_INIT01_VOLT_INC_ONLY BIT(2)
> +#define SVSB_INIT01_CLK_EN BIT(31)
> +
> +/* svs bank common setting */
> +#define SVSB_TZONE_HIGH_TEMP_MAX U32_MAX
> +#define SVSB_RUNCONFIG_DEFAULT 0x80000000
> +#define SVSB_DC_SIGNED_BIT 0x8000
> +#define SVSB_INTEN_INIT0x 0x00005f01
> +#define SVSB_INTEN_MONVOPEN 0x00ff0000
> +#define SVSB_EN_OFF 0x0
> +#define SVSB_EN_MASK 0x7
> +#define SVSB_EN_INIT01 0x1
> +#define SVSB_EN_INIT02 0x5
> +#define SVSB_EN_MON 0x2
> +#define SVSB_INTSTS_MONVOP 0x00ff0000
> +#define SVSB_INTSTS_COMPLETE 0x1
> +#define SVSB_INTSTS_CLEAN 0x00ffffff
> +
> +static DEFINE_SPINLOCK(mtk_svs_lock);
> +
> +/*
> + * enum svsb_phase - svs bank phase enumeration
> + * @SVSB_PHASE_INIT01: basic init for svs bank
> + * @SVSB_PHASE_INIT02: svs bank can provide voltages
> + * @SVSB_PHASE_MON: svs bank can provide voltages with thermal effect
> + * @SVSB_PHASE_ERROR: svs bank encouters unexpected condition
encounters
> + *
> + * Each svs bank has its own independent phase. We enable each svs bank by
> + * running their phase orderly. However, When svs bank ecnounters unexpected
encounters
> + * condition, it will fire an irq (PHASE_ERROR) to inform svs software.
> + *
> + * svs bank general phase-enabled order:
> + * SVSB_PHASE_INIT01 -> SVSB_PHASE_INIT02 -> SVSB_PHASE_MON
> + */
> +enum svsb_phase {
> + SVSB_PHASE_INIT01 = 0,
> + SVSB_PHASE_INIT02,
> + SVSB_PHASE_MON,
> + SVSB_PHASE_ERROR,
> +};
> +
> +enum svs_reg_index {
> + DESCHAR = 0,
> + TEMPCHAR,
> + DETCHAR,
> + AGECHAR,
> + DCCONFIG,
> + AGECONFIG,
> + FREQPCT30,
> + FREQPCT74,
> + LIMITVALS,
> + VBOOT,
> + DETWINDOW,
> + CONFIG,
> + TSCALCS,
> + RUNCONFIG,
> + SVSEN,
> + INIT2VALS,
> + DCVALUES,
> + AGEVALUES,
> + VOP30,
> + VOP74,
> + TEMP,
> + INTSTS,
> + INTSTSRAW,
> + INTEN,
> + CHKINT,
> + CHKSHIFT,
> + STATUS,
> + VDESIGN30,
> + VDESIGN74,
> + DVT30,
> + DVT74,
> + AGECOUNT,
> + SMSTATE0,
> + SMSTATE1,
> + CTL0,
> + DESDETSEC,
> + TEMPAGESEC,
> + CTRLSPARE0,
> + CTRLSPARE1,
> + CTRLSPARE2,
> + CTRLSPARE3,
> + CORESEL,
> + THERMINTST,
> + INTST,
> + THSTAGE0ST,
> + THSTAGE1ST,
> + THSTAGE2ST,
> + THAHBST0,
> + THAHBST1,
> + SPARE0,
> + SPARE1,
> + SPARE2,
> + SPARE3,
> + THSLPEVEB,
> + reg_num,
What do you need reg_num for? Maybe remove it?
If you need it, it should probably be named SVS_REG_NUM.
> +};
> +
> +static const u32 svs_regs_v2[] = {
> + [DESCHAR] = 0xc00,
> + [TEMPCHAR] = 0xc04,
> + [DETCHAR] = 0xc08,
> + [AGECHAR] = 0xc0c,
> + [DCCONFIG] = 0xc10,
> + [AGECONFIG] = 0xc14,
> + [FREQPCT30] = 0xc18,
> + [FREQPCT74] = 0xc1c,
> + [LIMITVALS] = 0xc20,
> + [VBOOT] = 0xc24,
> + [DETWINDOW] = 0xc28,
> + [CONFIG] = 0xc2c,
> + [TSCALCS] = 0xc30,
> + [RUNCONFIG] = 0xc34,
> + [SVSEN] = 0xc38,
> + [INIT2VALS] = 0xc3c,
> + [DCVALUES] = 0xc40,
> + [AGEVALUES] = 0xc44,
> + [VOP30] = 0xc48,
> + [VOP74] = 0xc4c,
> + [TEMP] = 0xc50,
> + [INTSTS] = 0xc54,
> + [INTSTSRAW] = 0xc58,
> + [INTEN] = 0xc5c,
> + [CHKINT] = 0xc60,
> + [CHKSHIFT] = 0xc64,
> + [STATUS] = 0xc68,
> + [VDESIGN30] = 0xc6c,
> + [VDESIGN74] = 0xc70,
> + [DVT30] = 0xc74,
> + [DVT74] = 0xc78,
> + [AGECOUNT] = 0xc7c,
> + [SMSTATE0] = 0xc80,
> + [SMSTATE1] = 0xc84,
> + [CTL0] = 0xc88,
> + [DESDETSEC] = 0xce0,
> + [TEMPAGESEC] = 0xce4,
> + [CTRLSPARE0] = 0xcf0,
> + [CTRLSPARE1] = 0xcf4,
> + [CTRLSPARE2] = 0xcf8,
> + [CTRLSPARE3] = 0xcfc,
> + [CORESEL] = 0xf00,
> + [THERMINTST] = 0xf04,
> + [INTST] = 0xf08,
> + [THSTAGE0ST] = 0xf0c,
> + [THSTAGE1ST] = 0xf10,
> + [THSTAGE2ST] = 0xf14,
> + [THAHBST0] = 0xf18,
> + [THAHBST1] = 0xf1c,
> + [SPARE0] = 0xf20,
> + [SPARE1] = 0xf24,
> + [SPARE2] = 0xf28,
> + [SPARE3] = 0xf2c,
> + [THSLPEVEB] = 0xf30,
> +};
> +
> +/*
> + * struct thermal_parameter - This is for storing thermal efuse data.
> + * We cacluate thermal efuse data to produce "mts" and "bts" for
calculate
> + * svs bank mon mode.
> + */
> +struct thermal_parameter {
> + int adc_ge_t;
> + int adc_oe_t;
> + int ge;
> + int oe;
> + int gain;
> + int o_vtsabb;
> + int o_vtsmcu1;
> + int o_vtsmcu2;
> + int o_vtsmcu3;
> + int o_vtsmcu4;
> + int o_vtsmcu5;
> + int degc_cali;
> + int adc_cali_en_t;
> + int o_slope;
> + int o_slope_sign;
> + int ts_id;
> +};
> +
> +/*
> + * struct svs_bank - svs bank representation
> + * @dev: svs bank device
> + * @opp_dev: device for opp table/buck control
> + * @pd_dev: power domain device for SOC mtcmos control
> + * @init_completion: the timeout completion for bank init
> + * @buck: phandle of the regulator
> + * @lock: mutex lock to protect voltage update process
> + * @suspended: suspend flag of this bank
> + * @pd_req: bank's power-domain on request
> + * @volt_offset: bank voltage offset controlled by svs software
> + * @mode_support: bank mode support.
> + * @opp_freqs: signed-off frequencies from default opp table
> + * @opp_volts: signed-off voltages from default opp table
> + * @freqs_pct: percent of "opp_freqs / freq_base" for bank init
> + * @volts: bank voltages
> + * @freq_base: reference frequency for bank init
> + * @vboot: voltage request for bank init01 stage only
> + * @volt_step: bank voltage step
> + * @volt_base: bank voltage base
> + * @init01_volt_flag: bank init01 voltage flag
> + * @phase: bank current phase
> + * @vmax: bank voltage maximum
> + * @vmin: bank votlage minimum
voltage
> + * @temp: bank temperature
> + * @temp_upper_bound: bank temperature upper bound
> + * @temp_lower_bound: bank temperature lower bound
> + * @tzone_high_temp: thermal zone high temperature threshold
> + * @tzone_high_temp_offset: thermal zone high temperature offset
> + * @tzone_low_temp: thermal zone low temperature threshold
> + * @tzone_low_temp_offset: thermal zone low temperature offset
> + * @core_sel: bank selection
> + * @opp_count: bank opp count
> + * @int_st: bank interrupt identification
> + * @sw_id: bank software identification
> + * @ctl0: bank thermal sensor selection
> + * @cpu_id: cpu core id for SVS CPU only
> + * @name: bank name
> + * @tzone_name: thermal zone name
> + * @buck_name: regulator name
> + *
> + * Other structure members which are not listed above are svs platform
> + * efuse data for bank init
> + */
> +struct svs_bank {
> + struct device *dev;
> + struct device *opp_dev;
> + struct device *pd_dev;
> + struct completion init_completion;
> + struct regulator *buck;
> + struct mutex lock; /* lock to protect voltage update process */
> + bool suspended;
> + bool pd_req;
> + s32 volt_offset;
> + u32 mode_support;
> + u32 opp_freqs[16];
> + u32 opp_volts[16];
> + u32 freqs_pct[16];
> + u32 volts[16];
> + u32 freq_base;
> + u32 vboot;
> + u32 volt_step;
> + u32 volt_base;
> + u32 init01_volt_flag;
> + u32 phase;
> + u32 vmax;
> + u32 vmin;
> + u32 bts;
> + u32 mts;
> + u32 bdes;
> + u32 mdes;
> + u32 mtdes;
> + u32 dcbdet;
> + u32 dcmdet;
> + u32 dthi;
> + u32 dtlo;
> + u32 det_window;
> + u32 det_max;
> + u32 age_config;
> + u32 age_voffset_in;
> + u32 agem;
> + u32 dc_config;
> + u32 dc_voffset_in;
> + u32 dvt_fixed;
> + u32 vco;
> + u32 chk_shift;
> + u32 temp;
> + u32 temp_upper_bound;
> + u32 temp_lower_bound;
> + u32 tzone_high_temp;
> + u32 tzone_high_temp_offset;
> + u32 tzone_low_temp;
> + u32 tzone_low_temp_offset;
> + u32 core_sel;
> + u32 opp_count;
> + u32 int_st;
> + u32 sw_id;
> + u32 ctl0;
> + u32 cpu_id;
> + u8 *name;
> + u8 *tzone_name;
> + u8 *buck_name;
> +};
> +
> +/*
> + * struct svs_platform - svs platform data
> + * @dev: svs platform device
> + * @base: svs platform register address base
> + * @main_clk: main clock for svs bank
> + * @pbank: phandle of svs bank and needs to be protected by spin_lock
> + * @banks: phandle of the banks that support
> + * @efuse_parsing: phandle of efuse parsing function
> + * @set_freqs_pct: phandle of set frequencies percent function
> + * @get_vops: phandle of get bank voltages function
> + * @irqflags: irq settings flags
> + * @fake_efuse: the flag for running svs with fake efuse
> + * @rst: svs reset control
> + * @regs: phandle to the registers map
> + * @efuse_num: the total number of svs platform efuse
> + * @tefuse_num: the total number of thermal efuse
> + * @bank_num: the total number of banks
> + * @efuse_check: the svs efuse check index
> + * @efuse: svs platform efuse data received from NVMEM framework
> + * @tefuse: thermal efuse data received from NVMEM framework
> + * @name: svs platform name
> + */
> +struct svs_platform {
> + struct device *dev;
> + void __iomem *base;
> + struct clk *main_clk;
> + struct svs_bank *pbank;
> + struct svs_bank *banks;
> + bool (*efuse_parsing)(struct svs_platform *svsp);
> + void (*set_freqs_pct)(struct svs_platform *svsp);
> + void (*get_vops)(struct svs_platform *svsp);
> + unsigned long irqflags;
> + bool fake_efuse;
> + struct reset_control *rst;
> + const u32 *regs;
> + size_t efuse_num;
> + size_t tefuse_num;
> + u32 bank_num;
> + u32 efuse_check;
> + u32 *efuse;
> + u32 *tefuse;
> + u8 *name;
> +};
> +
> +static u32 percent(u32 numerator, u32 denominator)
> +{
> + u32 pct;
> +
> + /* If not divide 1000, "numerator * 100" will have data overflow. */
> + numerator /= 1000;
> + denominator /= 1000;
> + pct = ((numerator * 100) + denominator - 1) / denominator;
pct = DIV_ROUND_UP(numerator * 100, denominator);
> + pct &= GENMASK(7, 0);
Why do you need this?
Maybe you should just return a u8 here?
> +
> + return pct;
> +}
> +
> +static u32 svs_readl(struct svs_platform *svsp, enum svs_reg_index rg_i)
> +{
> + return readl(svsp->base + svsp->regs[rg_i]);
> +}
> +
> +static void svs_writel(struct svs_platform *svsp, u32 val,
> + enum svs_reg_index rg_i)
> +{
> + writel(val, svsp->base + svsp->regs[rg_i]);
> +}
> +
> +static void svs_switch_bank(struct svs_platform *svsp)
> +{
> + struct svs_bank *svsb = svsp->pbank;
> +
> + svs_writel(svsp, svsb->core_sel, CORESEL);
> +}
> +
> +static u32 svs_bank_volt_to_opp_volt(u32 svsb_volt, u32 svsb_volt_step,
> + u32 svsb_volt_base)
> +{
> + u32 opp_u_volt;
> +
> + opp_u_volt = (svsb_volt * svsb_volt_step) + svsb_volt_base;
> +
> + return opp_u_volt;
return (svsb_volt * svsb_volt_step) + svsb_volt_base;
> +}
> +
> +static int svs_get_bank_zone_temperature(u8 *tzone_name, int *tzone_temp)
`const char *tzone_name` is probably more appropriate.
> +{
> + struct thermal_zone_device *tzd;
> +
> + tzd = thermal_zone_get_zone_by_name(tzone_name);
> + if (IS_ERR(tzd))
> + return PTR_ERR(tzd);
> +
> + return thermal_zone_get_temp(tzd, tzone_temp);
> +}
> +
> +static int svs_adjust_pm_opp_volts(struct svs_bank *svsb, bool force_update)
> +{
> + int tzone_temp, ret = -EPERM;
No need to initialize ret.
> + u32 i, svsb_volt, opp_volt, temp_offset = 0;
> +
> + mutex_lock(&svsb->lock);
> +
> + /*
> + * If svs bank is suspended, it means signed-off voltages are applied.
> + * Don't need to update opp voltage anymore.
> + */
> + if (svsb->suspended && !force_update) {
> + dev_notice(svsb->dev, "bank is suspended\n");
> + ret = -EPERM;
> + goto unlock_mutex;
> + }
> +
> + /* Get thermal effect */
> + if (svsb->phase == SVSB_PHASE_MON) {
> + if (svsb->temp > svsb->temp_upper_bound &&
> + svsb->temp < svsb->temp_lower_bound) {
> + dev_warn(svsb->dev, "svsb temp = 0x%x?\n", svsb->temp);
> + ret = -EINVAL;
> + goto unlock_mutex;
> + }
> +
> + ret = svs_get_bank_zone_temperature(svsb->tzone_name,
> + &tzone_temp);
> + if (ret) {
> + dev_err(svsb->dev, "no \"%s\"?(%d)?\n",
> + svsb->tzone_name, ret);
> + dev_err(svsb->dev, "set signed-off voltage\n");
Please merge the error message in one line (I'm not sure what "set
signed-off voltage" means here).
> + svsb->phase = SVSB_PHASE_ERROR;
> + }
> +
> + if (tzone_temp >= svsb->tzone_high_temp)
> + temp_offset += svsb->tzone_high_temp_offset;
> + else if (tzone_temp <= svsb->tzone_low_temp)
> + temp_offset += svsb->tzone_low_temp_offset;
> + }
> +
> + /* vmin <= svsb_volt (opp_volt) <= signed-off voltage */
> + for (i = 0; i < svsb->opp_count; i++) {
> + if (svsb->phase == SVSB_PHASE_MON) {
> + svsb_volt = max((svsb->volts[i] + svsb->volt_offset +
> + temp_offset), svsb->vmin);
parentheses inside the max parameter not needed
> + opp_volt = svs_bank_volt_to_opp_volt(svsb_volt,
> + svsb->volt_step,
> + svsb->volt_base);
> + } else if (svsb->phase == SVSB_PHASE_INIT02) {
> + svsb_volt = max((svsb->volts[i] + svsb->volt_offset),
> + svsb->vmin);
ditto.
> + opp_volt = svs_bank_volt_to_opp_volt(svsb_volt,
> + svsb->volt_step,
> + svsb->volt_base);
> + } else if (svsb->phase == SVSB_PHASE_ERROR) {
> + opp_volt = svsb->opp_volts[i];
> + } else {
> + dev_err(svsb->dev, "unknown phase: %u?\n", svsb->phase);
> + ret = -EINVAL;
> + goto unlock_mutex;
> + }
> +
> + opp_volt = min(opp_volt, svsb->opp_volts[i]);
> + ret = dev_pm_opp_adjust_voltage(svsb->opp_dev,
> + svsb->opp_freqs[i],
> + opp_volt, opp_volt,
> + svsb->opp_volts[i]);
> + if (ret) {
> + dev_err(svsb->dev, "set voltage fail: %d\n", ret);
> + goto unlock_mutex;
> + }
> + }
> +
> +unlock_mutex:
> + mutex_unlock(&svsb->lock);
> +
> + return ret;
> +}
> +
> +static u32 interpolate(u32 f0, u32 f1, u32 v0, u32 v1, u32 fx)
> +{
> + u32 vy;
> +
> + if (v0 == v1 || f0 == f1)
> + return v0;
> +
> + /* *100 to have decimal fraction factor, +99 for rounding up. */
> + vy = (v0 * 100) - ((((v0 - v1) * 100) / (f0 - f1)) * (f0 - fx));
> + vy = (vy + 99) / 100;
vy = DIV_ROUND_UP(vy, 100);
> +
> + return vy;
> +}
> +
> +static void svs_get_vops_v2(struct svs_platform *svsp)
> +{
> + struct svs_bank *svsb = svsp->pbank;
> + u32 temp, i;
> +
> + temp = svs_readl(svsp, VOP74);
> + svsb->volts[14] = (temp >> 24) & GENMASK(7, 0);
> + svsb->volts[12] = (temp >> 16) & GENMASK(7, 0);
> + svsb->volts[10] = (temp >> 8) & GENMASK(7, 0);
> + svsb->volts[8] = (temp & GENMASK(7, 0));
> +
> + temp = svs_readl(svsp, VOP30);
> + svsb->volts[6] = (temp >> 24) & GENMASK(7, 0);
> + svsb->volts[4] = (temp >> 16) & GENMASK(7, 0);
> + svsb->volts[2] = (temp >> 8) & GENMASK(7, 0);
> + svsb->volts[0] = (temp & GENMASK(7, 0));
> +
> + for (i = 0; i <= 7; i++) {
> + if (i < 7) {
> + svsb->volts[(i * 2) + 1] =
> + interpolate(svsb->freqs_pct[i * 2],
> + svsb->freqs_pct[(i + 1) * 2],
> + svsb->volts[i * 2],
> + svsb->volts[(i + 1) * 2],
> + svsb->freqs_pct[(i * 2) + 1]);
> + } else if (i == 7) {
> + svsb->volts[(i * 2) + 1] =
> + interpolate(svsb->freqs_pct[(i - 1) * 2],
> + svsb->freqs_pct[i * 2],
> + svsb->volts[(i - 1) * 2],
> + svsb->volts[i * 2],
> + svsb->freqs_pct[(i * 2) + 1]);
> + }
> + }
Please double-check, but I think we can do:
for (i = 0; i <= 12; i += 2) {
svsb->volts[i + 1] =
interpolate(svsb->freqs_pct[i],
svsb->freqs_pct[i + 2],
svsb->volts[i],
svsb->volts[i + 2],
svsb->freqs_pct[i + 1]);
}
svsb->volts[i + 1] =
interpolate(svsb->freqs_pct[i - 2],
svsb->freqs_pct[i],
svsb->volts[i - 2],
svsb->volts[i],
svsb->freqs_pct[i + 1]);
(or maybe replace i with 14 in the computation for this last iteration.
> +}
> +
> +static void svs_set_freqs_pct_v2(struct svs_platform *svsp)
> +{
> + struct svs_bank *svsb = svsp->pbank;
> +
> + svs_writel(svsp,
> + ((svsb->freqs_pct[14] << 24) & GENMASK(31, 24)) |
Well you already took care of making sure freqs_pct does not have more
than 8 bits set, so I don't think you need GENMASK(31, 24).
> + ((svsb->freqs_pct[12] << 16) & GENMASK(23, 16)) |
> + ((svsb->freqs_pct[10] << 8) & GENMASK(15, 8)) |
> + ((svsb->freqs_pct[8]) & GENMASK(7, 0)),
> + FREQPCT74);
> +
> + svs_writel(svsp,
> + ((svsb->freqs_pct[6] << 24) & GENMASK(31, 24)) |
> + ((svsb->freqs_pct[4] << 16) & GENMASK(23, 16)) |
> + ((svsb->freqs_pct[2] << 8) & GENMASK(15, 8)) |
> + (svsb->freqs_pct[0] & GENMASK(7, 0)),
> + FREQPCT30);
> +}
> +
> +static void svs_set_bank_phase(struct svs_platform *svsp, u32 target_phase)
> +{
> + struct svs_bank *svsb = svsp->pbank;
> + u32 des_char, temp_char, det_char, limit_vals;
> + u32 init2vals, ts_calcs, val, filter, i;
> +
> + svs_switch_bank(svsp);
> +
> + des_char = ((svsb->bdes << 8) & GENMASK(15, 8)) |
> + (svsb->mdes & GENMASK(7, 0));
Similar to my suggestion about, consider chaging bdes type to u8 so
you don't need all these masks?
> + svs_writel(svsp, des_char, DESCHAR);
> +
> + temp_char = ((svsb->vco << 16) & GENMASK(23, 16)) |
> + ((svsb->mtdes << 8) & GENMASK(15, 8)) |
> + (svsb->dvt_fixed & GENMASK(7, 0));
> + svs_writel(svsp, temp_char, TEMPCHAR);
> +
> + det_char = ((svsb->dcbdet << 8) & GENMASK(15, 8)) |
> + (svsb->dcmdet & GENMASK(7, 0));
> + svs_writel(svsp, det_char, DETCHAR);
> +
> + svs_writel(svsp, svsb->dc_config, DCCONFIG);
> + svs_writel(svsp, svsb->age_config, AGECONFIG);
> +
> + if (!svsb->agem) {
> + svs_writel(svsp, SVSB_RUNCONFIG_DEFAULT, RUNCONFIG);
> + } else {
> + val = 0x0;
> +
> + for (i = 0; i < 24; i += 2) {
> + filter = 0x3 << i;
> +
> + if (!(svsb->age_config & filter))
> + val |= (0x1 << i);
> + else
> + val |= (svsb->age_config & filter);
> + }
> + svs_writel(svsp, val, RUNCONFIG);
> + }
> +
> + svsp->set_freqs_pct(svsp);
> +
> + limit_vals = ((svsb->vmax << 24) & GENMASK(31, 24)) |
> + ((svsb->vmin << 16) & GENMASK(23, 16)) |
> + ((svsb->dthi << 8) & GENMASK(15, 8)) |
> + (svsb->dtlo & GENMASK(7, 0));
> + svs_writel(svsp, limit_vals, LIMITVALS);
> + svs_writel(svsp, (svsb->vboot & GENMASK(7, 0)), VBOOT);
> + svs_writel(svsp, (svsb->det_window & GENMASK(15, 0)), DETWINDOW);
> + svs_writel(svsp, (svsb->det_max & GENMASK(15, 0)), CONFIG);
> +
> + if (svsb->chk_shift)
> + svs_writel(svsp, (svsb->chk_shift & GENMASK(7, 0)), CHKSHIFT);
> +
> + if (svsb->ctl0)
> + svs_writel(svsp, svsb->ctl0, CTL0);
> +
> + svs_writel(svsp, SVSB_INTSTS_CLEAN, INTSTS);
> +
> + switch (target_phase) {
> + case SVSB_PHASE_INIT01:
> + svs_writel(svsp, SVSB_INTEN_INIT0x, INTEN);
> + svs_writel(svsp, SVSB_EN_INIT01, SVSEN);
> + break;
> + case SVSB_PHASE_INIT02:
> + svs_writel(svsp, SVSB_INTEN_INIT0x, INTEN);
> + init2vals = ((svsb->age_voffset_in << 16) & GENMASK(31, 16)) |
> + (svsb->dc_voffset_in & GENMASK(15, 0));
> + svs_writel(svsp, init2vals, INIT2VALS);
> + svs_writel(svsp, SVSB_EN_INIT02, SVSEN);
> + break;
> + case SVSB_PHASE_MON:
> + ts_calcs = ((svsb->bts << 12) & GENMASK(23, 12)) |
> + (svsb->mts & GENMASK(11, 0));
> + svs_writel(svsp, ts_calcs, TSCALCS);
> + svs_writel(svsp, SVSB_INTEN_MONVOPEN, INTEN);
> + svs_writel(svsp, SVSB_EN_MON, SVSEN);
> + break;
> + default:
> + WARN_ON(1);
> + break;
> + }
> +}
> +
> +static inline void svs_init01_isr_handler(struct svs_platform *svsp)
> +{
> + struct svs_bank *svsb = svsp->pbank;
> +
> + dev_info(svsb->dev, "%s: VDN74~30:0x%08x~0x%08x, DC:0x%08x\n",
dev_dbg?
> + __func__, svs_readl(svsp, VDESIGN74),
> + svs_readl(svsp, VDESIGN30), svs_readl(svsp, DCVALUES));
> +
> + svsb->phase = SVSB_PHASE_INIT01;
> + svsb->dc_voffset_in = ~(svs_readl(svsp, DCVALUES) & GENMASK(15, 0)) + 1;
> + if (svsb->init01_volt_flag == SVSB_INIT01_VOLT_IGNORE)
> + svsb->dc_voffset_in = 0;
> + else if ((svsb->dc_voffset_in & SVSB_DC_SIGNED_BIT) &&
> + (svsb->init01_volt_flag == SVSB_INIT01_VOLT_INC_ONLY))
> + svsb->dc_voffset_in = 0;
Merge these 2 if tests into one, since you do the same operation in both cases.
> +
> + svsb->age_voffset_in = svs_readl(svsp, AGEVALUES) & GENMASK(15, 0);
> +
> + svs_writel(svsp, SVSB_EN_OFF, SVSEN);
> + svs_writel(svsp, SVSB_INTSTS_COMPLETE, INTSTS);
> +
> + /* svs init01 clock gating */
> + svsb->core_sel &= ~SVSB_INIT01_CLK_EN;
> +}
> +
> +static inline void svs_init02_isr_handler(struct svs_platform *svsp)
> +{
> + struct svs_bank *svsb = svsp->pbank;
> +
> + dev_info(svsb->dev, "%s: VOP74~30:0x%08x~0x%08x, DC:0x%08x\n",
> + __func__, svs_readl(svsp, VOP74), svs_readl(svsp, VOP30),
> + svs_readl(svsp, DCVALUES));
dev_dbg?
> +
> + svsb->phase = SVSB_PHASE_INIT02;
> + svsp->get_vops(svsp);
> +
> + svs_writel(svsp, SVSB_EN_OFF, SVSEN);
> + svs_writel(svsp, SVSB_INTSTS_COMPLETE, INTSTS);
> +}
> +
> +static inline void svs_mon_mode_isr_handler(struct svs_platform *svsp)
> +{
> + struct svs_bank *svsb = svsp->pbank;
> +
> + svsb->phase = SVSB_PHASE_MON;
> + svsb->temp = svs_readl(svsp, TEMP) & GENMASK(7, 0);
> + svsp->get_vops(svsp);
> +
> + svs_writel(svsp, SVSB_INTSTS_MONVOP, INTSTS);
> +}
> +
> +static inline void svs_error_isr_handler(struct svs_platform *svsp)
> +{
> + struct svs_bank *svsb = svsp->pbank;
> +
> + dev_err(svsb->dev, "%s: CORESEL = 0x%08x\n",
> + __func__, svs_readl(svsp, CORESEL));
> + dev_err(svsb->dev, "SVSEN = 0x%08x, INTSTS = 0x%08x\n",
> + svs_readl(svsp, SVSEN), svs_readl(svsp, INTSTS));
> + dev_err(svsb->dev, "SMSTATE0 = 0x%08x, SMSTATE1 = 0x%08x\n",
> + svs_readl(svsp, SMSTATE0), svs_readl(svsp, SMSTATE1));
> + dev_err(svsb->dev, "TEMP = 0x%08x\n", svs_readl(svsp, TEMP));
> +
> + svsb->mode_support = SVSB_MODE_ALL_DISABLE;
> + svsb->phase = SVSB_PHASE_ERROR;
> +
> + svs_writel(svsp, SVSB_EN_OFF, SVSEN);
> + svs_writel(svsp, SVSB_INTSTS_CLEAN, INTSTS);
> +}
> +
> +static irqreturn_t svs_isr(int irq, void *data)
> +{
> + struct svs_platform *svsp = (struct svs_platform *)data;
cast not needed.
> + struct svs_bank *svsb = NULL;
> + unsigned long flags;
> + u32 idx, int_sts, svs_en;
> +
> + for (idx = 0; idx < svsp->bank_num; idx++) {
> + svsb = &svsp->banks[idx];
> +
> + spin_lock_irqsave(&mtk_svs_lock, flags);
> + svsp->pbank = svsb;
> +
> + /* Find out which svs bank fires interrupt */
> + if (svsb->int_st & svs_readl(svsp, INTST)) {
> + spin_unlock_irqrestore(&mtk_svs_lock, flags);
> + continue;
> + }
> +
> + if (!svsb->suspended) {
> + svs_switch_bank(svsp);
> + int_sts = svs_readl(svsp, INTSTS);
> + svs_en = svs_readl(svsp, SVSEN);
> +
> + if (int_sts == SVSB_INTSTS_COMPLETE &&
> + ((svs_en & SVSB_EN_MASK) == SVSB_EN_INIT01))
> + svs_init01_isr_handler(svsp);
> + else if ((int_sts == SVSB_INTSTS_COMPLETE) &&
> + ((svs_en & SVSB_EN_MASK) == SVSB_EN_INIT02))
> + svs_init02_isr_handler(svsp);
> + else if (!!(int_sts & SVSB_INTSTS_MONVOP))
!! is not required.
> + svs_mon_mode_isr_handler(svsp);
> + else
> + svs_error_isr_handler(svsp);
> + }
> +
> + spin_unlock_irqrestore(&mtk_svs_lock, flags);
> + break;
> + }
This will panic if svsb is NULL, is that ok or do you want to catch that?
> +
> + if (svsb->phase != SVSB_PHASE_INIT01)
> + svs_adjust_pm_opp_volts(svsb, false);
> +
> + if (svsb->phase == SVSB_PHASE_INIT01 ||
> + svsb->phase == SVSB_PHASE_INIT02)
> + complete(&svsb->init_completion);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static void svs_mon_mode(struct svs_platform *svsp)
> +{
> + struct svs_bank *svsb;
> + unsigned long flags;
> + u32 idx;
> +
> + for (idx = 0; idx < svsp->bank_num; idx++) {
> + svsb = &svsp->banks[idx];
> +
> + if (!(svsb->mode_support & SVSB_MODE_MON))
> + continue;
> +
> + spin_lock_irqsave(&mtk_svs_lock, flags);
> + svsp->pbank = svsb;
> + svs_set_bank_phase(svsp, SVSB_PHASE_MON);
> + spin_unlock_irqrestore(&mtk_svs_lock, flags);
> + }
> +}
> +
> +static int svs_init02(struct svs_platform *svsp)
> +{
> + struct svs_bank *svsb;
> + unsigned long flags, time_left;
> + u32 idx;
> +
> + for (idx = 0; idx < svsp->bank_num; idx++) {
> + svsb = &svsp->banks[idx];
> +
> + if (!(svsb->mode_support & SVSB_MODE_INIT02))
> + continue;
> +
> + reinit_completion(&svsb->init_completion);
> + spin_lock_irqsave(&mtk_svs_lock, flags);
> + svsp->pbank = svsb;
> + svs_set_bank_phase(svsp, SVSB_PHASE_INIT02);
> + spin_unlock_irqrestore(&mtk_svs_lock, flags);
> +
> + time_left =
> + wait_for_completion_timeout(&svsb->init_completion,
> + msecs_to_jiffies(2000));
> + if (!time_left) {
> + dev_err(svsb->dev, "init02 completion timeout\n");
> + return -EBUSY;
> + }
> + }
> +
> + return 0;
> +}
> +
> +static int svs_init01(struct svs_platform *svsp)
> +{
> + struct svs_bank *svsb;
> + struct pm_qos_request *qos_request;
> + unsigned long flags, time_left;
> + bool search_done, does_svsb_set_pd_on;
> + int ret = 0;
> + u32 opp_freqs, opp_vboot, buck_volt, idx, i;
> +
> + qos_request = kzalloc(sizeof(*qos_request), GFP_KERNEL);
> + if (!qos_request)
> + return -ENOMEM;
> +
> + /* Let CPUs leave idle-off state for initializing svs_init01. */
> + cpu_latency_qos_add_request(qos_request, 0);
> +
> + /*
> + * Sometimes two svs banks use the same buck.
> + * Therefore, we set each svs bank to vboot voltage first.
> + */
> + for (idx = 0; idx < svsp->bank_num; idx++) {
> + svsb = &svsp->banks[idx];
> +
> + if (!(svsb->mode_support & SVSB_MODE_INIT01))
> + continue;
> +
> + search_done = false;
> + does_svsb_set_pd_on = false;
> +
> + if (regulator_set_mode(svsb->buck, REGULATOR_MODE_FAST))
> + dev_notice(svsb->dev, "set fast mode fail\n");
> +
> + if (svsb->pd_req) {
> + ret = regulator_enable(svsb->buck);
> + if (ret) {
> + dev_err(svsb->dev, "\"%s\" enable fail: %d\n",
> + svsb->buck_name, ret);
> + goto init01_finish;
> + }
> +
> + if (!pm_runtime_enabled(svsb->pd_dev)) {
> + pm_runtime_enable(svsb->pd_dev);
> + does_svsb_set_pd_on = true;
> + }
> +
> + ret = pm_runtime_get_sync(svsb->pd_dev);
> + if (ret < 0) {
> + dev_err(svsb->dev, "mtcmos on fail: %d\n",
> + ret);
> + goto init01_finish;
> + }
> + }
> +
> + /*
> + * Find the fastest freq that can be run at vboot and
> + * fix to that freq until svs_init01 is done.
> + */
> + opp_vboot = svs_bank_volt_to_opp_volt(svsb->vboot,
> + svsb->volt_step,
> + svsb->volt_base);
> +
> + for (i = 0; i < svsb->opp_count; i++) {
> + opp_freqs = svsb->opp_freqs[i];
> + if (!search_done && svsb->opp_volts[i] <= opp_vboot) {
> + ret = dev_pm_opp_adjust_voltage(svsb->opp_dev,
> + opp_freqs,
> + opp_vboot,
> + opp_vboot,
> + opp_vboot);
> + if (ret) {
> + dev_err(svsb->dev,
> + "set voltage fail: %d\n", ret);
> + goto init01_finish;
> + }
> +
> + search_done = true;
> + } else {
> + dev_pm_opp_disable(svsb->opp_dev,
> + svsb->opp_freqs[i]);
> + }
> + }
> + }
> +
> + /* svs bank init01 begins */
> + for (idx = 0; idx < svsp->bank_num; idx++) {
> + svsb = &svsp->banks[idx];
> +
> + if (!(svsb->mode_support & SVSB_MODE_INIT01))
> + continue;
> +
> + opp_vboot = svs_bank_volt_to_opp_volt(svsb->vboot,
> + svsb->volt_step,
> + svsb->volt_base);
> +
> + buck_volt = regulator_get_voltage(svsb->buck);
> + if (buck_volt != opp_vboot) {
> + dev_err(svsb->dev,
> + "buck voltage: %u, expected vboot: %u\n",
> + buck_volt, opp_vboot);
> + ret = -EPERM;
> + goto init01_finish;
> + }
> +
> + spin_lock_irqsave(&mtk_svs_lock, flags);
> + svsp->pbank = svsb;
> + svs_set_bank_phase(svsp, SVSB_PHASE_INIT01);
> + spin_unlock_irqrestore(&mtk_svs_lock, flags);
> +
> + time_left =
> + wait_for_completion_timeout(&svsb->init_completion,
> + msecs_to_jiffies(2000));
> + if (!time_left) {
> + dev_err(svsb->dev, "init01 completion timeout\n");
> + ret = -EBUSY;
> + goto init01_finish;
> + }
> + }
> +
> +init01_finish:
> + for (idx = 0; idx < svsp->bank_num; idx++) {
> + svsb = &svsp->banks[idx];
> +
> + if (!(svsb->mode_support & SVSB_MODE_INIT01))
> + continue;
> +
> + for (i = 0; i < svsb->opp_count; i++)
> + dev_pm_opp_enable(svsb->opp_dev, svsb->opp_freqs[i]);
> +
> + if (regulator_set_mode(svsb->buck, REGULATOR_MODE_NORMAL))
> + dev_notice(svsb->dev, "fail to set normal mode\n");
> +
> + if (svsb->pd_req) {
> + if (pm_runtime_put_sync(svsb->pd_dev))
> + dev_err(svsb->dev, "mtcmos off fail\n");
> +
> + if (does_svsb_set_pd_on) {
> + pm_runtime_disable(svsb->pd_dev);
> + does_svsb_set_pd_on = false;
> + }
> +
> + if (regulator_disable(svsb->buck))
> + dev_err(svsb->dev, "disable power fail\n");
> + }
> + }
> +
> + cpu_latency_qos_remove_request(qos_request);
> + kfree(qos_request);
> +
> + return ret;
> +}
> +
> +static int svs_start(struct svs_platform *svsp)
> +{
> + int ret;
> +
> + ret = svs_init01(svsp);
> + if (ret)
> + return ret;
> +
> + ret = svs_init02(svsp);
> + if (ret)
> + return ret;
> +
> + svs_mon_mode(svsp);
> +
> + return ret;
Or just return 0;
> +}
> +
> +static struct device *svs_get_subsys_device(struct svs_platform *svsp,
> + u8 *node_name)
> +{
> + struct platform_device *pdev;
> + struct device_node *np;
> +
> + np = of_find_node_by_name(NULL, node_name);
> + if (!np) {
> + dev_err(svsp->dev, "cannot find %s node\n", node_name);
> + return ERR_PTR(-ENODEV);
> + }
> +
> + pdev = of_find_device_by_node(np);
> + if (!pdev) {
> + of_node_put(np);
> + dev_err(svsp->dev, "cannot find pdev by %s\n", node_name);
> + return ERR_PTR(-ENXIO);
> + }
> +
> + of_node_put(np);
> +
> + return &pdev->dev;
> +}
> +
> +static struct device *svs_add_device_link(struct svs_platform *svsp,
> + u8 *node_name)
> +{
> + struct device *dev;
> + struct device_link *sup_link;
> +
> + if (!node_name) {
> + dev_err(svsp->dev, "node name cannot be null\n");
> + return ERR_PTR(-EINVAL);
> + }
> +
> + dev = svs_get_subsys_device(svsp, node_name);
> + if (IS_ERR(dev))
> + return dev;
> +
> + sup_link = device_link_add(svsp->dev, dev,
> + DL_FLAG_AUTOREMOVE_CONSUMER);
> +
> + if (sup_link->status == DL_STATE_DORMANT)
> + return ERR_PTR(-EPROBE_DEFER);
> +
> + return dev;
> +}
> +
> +static int svs_resource_setup(struct svs_platform *svsp)
> +{
> + struct svs_bank *svsb;
> + struct dev_pm_opp *opp;
> + unsigned long freq;
> + int count, ret;
> + u32 idx, i;
> +
> + dev_set_drvdata(svsp->dev, svsp);
> +
> + for (idx = 0; idx < svsp->bank_num; idx++) {
> + svsb = &svsp->banks[idx];
> +
> + switch (svsb->sw_id) {
> + case SVSB_CPU_LITTLE:
> + svsb->name = "SVSB_CPU_LITTLE";
> + break;
> + case SVSB_CPU_BIG:
> + svsb->name = "SVSB_CPU_BIG";
> + break;
> + case SVSB_CCI:
> + svsb->name = "SVSB_CCI";
> + break;
> + case SVSB_GPU:
> + svsb->name = "SVSB_GPU";
> + break;
> + default:
> + WARN_ON(1);
> + return -EINVAL;
> + }
> +
> + svsb->dev = devm_kzalloc(svsp->dev, sizeof(*svsb->dev),
> + GFP_KERNEL);
> + if (!svsb->dev)
> + return -ENOMEM;
> +
> + ret = dev_set_name(svsb->dev, svsb->name);
> + if (ret)
> + return ret;
> +
> + dev_set_drvdata(svsb->dev, svsp);
> +
> + ret = dev_pm_opp_of_add_table(svsb->opp_dev);
> + if (ret) {
> + dev_err(svsb->dev, "add opp table fail: %d\n", ret);
> + return ret;
> + }
> +
> + mutex_init(&svsb->lock);
> + init_completion(&svsb->init_completion);
> +
> + svsb->buck = devm_regulator_get_optional(svsb->opp_dev,
> + svsb->buck_name);
> + if (IS_ERR(svsb->buck)) {
> + dev_err(svsb->dev, "cannot get \"%s-supply\"\n",
> + svsb->buck_name);
> + return PTR_ERR(svsb->buck);
> + }
> +
> + count = dev_pm_opp_get_opp_count(svsb->opp_dev);
> + if (svsb->opp_count != count) {
> + dev_err(svsb->dev,
> + "opp_count not \"%u\" but get \"%d\"?\n",
> + svsb->opp_count, count);
> + return count;
> + }
> +
> + for (i = 0, freq = U32_MAX; i < svsb->opp_count; i++, freq--) {
> + opp = dev_pm_opp_find_freq_floor(svsb->opp_dev, &freq);
> + if (IS_ERR(opp)) {
> + dev_err(svsb->dev, "cannot find freq = %ld\n",
> + PTR_ERR(opp));
> + return PTR_ERR(opp);
> + }
> +
> + svsb->opp_freqs[i] = freq;
> + svsb->opp_volts[i] = dev_pm_opp_get_voltage(opp);
> + svsb->freqs_pct[i] = percent(svsb->opp_freqs[i],
> + svsb->freq_base);
> + dev_pm_opp_put(opp);
> + }
> + }
> +
> + return 0;
> +}
> +
> +static bool svs_mt8183_efuse_parsing(struct svs_platform *svsp)
> +{
> + struct thermal_parameter tp;
> + struct svs_bank *svsb;
> + bool mon_mode_support = true;
> + int format[6], x_roomt[6], tb_roomt = 0;
> + struct nvmem_cell *cell;
> + u32 idx, i, ft_pgm, mts, temp0, temp1, temp2;
> +
> + if (svsp->fake_efuse) {
> + pr_notice("fake efuse\n");
> + svsp->efuse[0] = 0x00310080;
> + svsp->efuse[1] = 0xabfbf757;
> + svsp->efuse[2] = 0x47c747c7;
> + svsp->efuse[3] = 0xabfbf757;
> + svsp->efuse[4] = 0xe7fca0ec;
> + svsp->efuse[5] = 0x47bf4b88;
> + svsp->efuse[6] = 0xabfb8fa5;
> + svsp->efuse[7] = 0xabfb217b;
> + svsp->efuse[8] = 0x4bf34be1;
> + svsp->efuse[9] = 0xabfb670d;
> + svsp->efuse[16] = 0xabfbc653;
> + svsp->efuse[17] = 0x47f347e1;
> + svsp->efuse[18] = 0xabfbd848;
> + }
Looks like debugging code, drop this?
> +
> + for (i = 0; i < svsp->efuse_num; i++)
> + if (svsp->efuse[i])
> + dev_notice(svsp->dev, "M_HW_RES%d: 0x%08x\n",
> + i, svsp->efuse[i]);
dev_dbg?
> +
> + /* Svs efuse parsing */
> + ft_pgm = (svsp->efuse[0] >> 4) & GENMASK(3, 0);
> +
> + for (idx = 0; idx < svsp->bank_num; idx++) {
> + svsb = &svsp->banks[idx];
> +
> + if (ft_pgm <= 1)
> + svsb->init01_volt_flag = SVSB_INIT01_VOLT_IGNORE;
> +
> + switch (svsb->sw_id) {
> + case SVSB_CPU_LITTLE:
> + svsb->bdes = svsp->efuse[16] & GENMASK(7, 0);
> + svsb->mdes = (svsp->efuse[16] >> 8) & GENMASK(7, 0);
> + svsb->dcbdet = (svsp->efuse[16] >> 16) & GENMASK(7, 0);
> + svsb->dcmdet = (svsp->efuse[16] >> 24) & GENMASK(7, 0);
> + svsb->mtdes = (svsp->efuse[17] >> 16) & GENMASK(7, 0);
Again, if all of those values were u8, there'd be no need for these GENMASK
> +
> + if (ft_pgm <= 3)
> + svsb->volt_offset += 10;
> + else
> + svsb->volt_offset += 2;
> + break;
> + case SVSB_CPU_BIG:
> + svsb->bdes = svsp->efuse[18] & GENMASK(7, 0);
> + svsb->mdes = (svsp->efuse[18] >> 8) & GENMASK(7, 0);
> + svsb->dcbdet = (svsp->efuse[18] >> 16) & GENMASK(7, 0);
> + svsb->dcmdet = (svsp->efuse[18] >> 24) & GENMASK(7, 0);
> + svsb->mtdes = svsp->efuse[17] & GENMASK(7, 0);
> +
> + if (ft_pgm <= 3)
> + svsb->volt_offset += 15;
> + else
> + svsb->volt_offset += 12;
> + break;
> + case SVSB_CCI:
> + svsb->bdes = svsp->efuse[4] & GENMASK(7, 0);
> + svsb->mdes = (svsp->efuse[4] >> 8) & GENMASK(7, 0);
> + svsb->dcbdet = (svsp->efuse[4] >> 16) & GENMASK(7, 0);
> + svsb->dcmdet = (svsp->efuse[4] >> 24) & GENMASK(7, 0);
> + svsb->mtdes = (svsp->efuse[5] >> 16) & GENMASK(7, 0);
> +
> + if (ft_pgm <= 3)
> + svsb->volt_offset += 10;
> + else
> + svsb->volt_offset += 2;
> + break;
> + case SVSB_GPU:
> + svsb->bdes = svsp->efuse[6] & GENMASK(7, 0);
> + svsb->mdes = (svsp->efuse[6] >> 8) & GENMASK(7, 0);
> + svsb->dcbdet = (svsp->efuse[6] >> 16) & GENMASK(7, 0);
> + svsb->dcmdet = (svsp->efuse[6] >> 24) & GENMASK(7, 0);
> + svsb->mtdes = svsp->efuse[5] & GENMASK(7, 0);
> +
> + if (ft_pgm >= 2) {
> + svsb->freq_base = 800000000; /* 800MHz */
> + svsb->dvt_fixed = 2;
> + }
> + break;
> + default:
> + break;
> + }
> + }
> +
> + /* Get thermal efuse by nvmem */
> + cell = nvmem_cell_get(svsp->dev, "t-calibration-data");
> + if (IS_ERR_OR_NULL(cell)) {
> + dev_err(svsp->dev, "no thermal cell, no mon mode\n");
> + for (idx = 0; idx < svsp->bank_num; idx++) {
> + svsb = &svsp->banks[idx];
> + svsb->mode_support &= ~SVSB_MODE_MON;
> + }
> +
> + return true;
> + }
> +
> + svsp->tefuse = (u32 *)nvmem_cell_read(cell, &svsp->tefuse_num);
Cast not needed.
Also, this need to be freed somewhere in remove code (kfree(svsp->tefuse)).
And it seems like svsp->tefuse is only used in this function, can you
just allocate it here?
> + svsp->tefuse_num /= sizeof(u32);
> + nvmem_cell_put(cell);
> +
> + if (svsp->fake_efuse) {
> + svsp->tefuse[0] = 0x02873f69;
> + svsp->tefuse[1] = 0xa11d9142;
> + svsp->tefuse[2] = 0xa2526900;
> + }
> +
> + /* Thermal efuse parsing */
> + tp.adc_ge_t = (svsp->tefuse[1] >> 22) & GENMASK(9, 0);
> + tp.adc_oe_t = (svsp->tefuse[1] >> 12) & GENMASK(9, 0);
> +
> + tp.o_vtsmcu1 = (svsp->tefuse[0] >> 17) & GENMASK(8, 0);
> + tp.o_vtsmcu2 = (svsp->tefuse[0] >> 8) & GENMASK(8, 0);
> + tp.o_vtsmcu3 = svsp->tefuse[1] & GENMASK(8, 0);
> + tp.o_vtsmcu4 = (svsp->tefuse[2] >> 23) & GENMASK(8, 0);
> + tp.o_vtsmcu5 = (svsp->tefuse[2] >> 5) & GENMASK(8, 0);
> + tp.o_vtsabb = (svsp->tefuse[2] >> 14) & GENMASK(8, 0);
> +
> + tp.degc_cali = (svsp->tefuse[0] >> 1) & GENMASK(5, 0);
> + tp.adc_cali_en_t = svsp->tefuse[0] & BIT(0);
> + tp.o_slope_sign = (svsp->tefuse[0] >> 7) & BIT(0);
> +
> + tp.ts_id = (svsp->tefuse[1] >> 9) & BIT(0);
> + tp.o_slope = (svsp->tefuse[0] >> 26) & GENMASK(5, 0);
> +
> + if (tp.adc_cali_en_t == 1) {
> + if (!tp.ts_id)
> + tp.o_slope = 0;
> +
> + if ((tp.adc_ge_t < 265 || tp.adc_ge_t > 758) ||
> + (tp.adc_oe_t < 265 || tp.adc_oe_t > 758) ||
> + (tp.o_vtsmcu1 < -8 || tp.o_vtsmcu1 > 484) ||
> + (tp.o_vtsmcu2 < -8 || tp.o_vtsmcu2 > 484) ||
> + (tp.o_vtsmcu3 < -8 || tp.o_vtsmcu3 > 484) ||
> + (tp.o_vtsmcu4 < -8 || tp.o_vtsmcu4 > 484) ||
> + (tp.o_vtsmcu5 < -8 || tp.o_vtsmcu5 > 484) ||
> + (tp.o_vtsabb < -8 || tp.o_vtsabb > 484) ||
> + (tp.degc_cali < 1 || tp.degc_cali > 63)) {
> + dev_err(svsp->dev, "bad thermal efuse, no mon mode\n");
> + mon_mode_support = false;
> + }
> + } else {
> + dev_err(svsp->dev, "no thermal efuse, no mon mode\n");
> + mon_mode_support = false;
> + }
> +
> + if (!mon_mode_support) {
> + for (idx = 0; idx < svsp->bank_num; idx++) {
> + svsb = &svsp->banks[idx];
> + svsb->mode_support &= ~SVSB_MODE_MON;
> + }
> +
> + return true;
> + }
> +
> + tp.ge = ((tp.adc_ge_t - 512) * 10000) / 4096;
> + tp.oe = (tp.adc_oe_t - 512);
> + tp.gain = (10000 + tp.ge);
> +
> + format[0] = (tp.o_vtsmcu1 + 3350 - tp.oe);
> + format[1] = (tp.o_vtsmcu2 + 3350 - tp.oe);
> + format[2] = (tp.o_vtsmcu3 + 3350 - tp.oe);
> + format[3] = (tp.o_vtsmcu4 + 3350 - tp.oe);
> + format[4] = (tp.o_vtsmcu5 + 3350 - tp.oe);
> + format[5] = (tp.o_vtsabb + 3350 - tp.oe);
> +
> + for (i = 0; i < 6; i++)
> + x_roomt[i] = (((format[i] * 10000) / 4096) * 10000) / tp.gain;
> +
> + temp0 = (10000 * 100000 / tp.gain) * 15 / 18;
> +
> + if (!tp.o_slope_sign)
> + mts = (temp0 * 10) / (1534 + tp.o_slope * 10);
> + else
> + mts = (temp0 * 10) / (1534 - tp.o_slope * 10);
> +
> + for (idx = 0; idx < svsp->bank_num; idx++) {
> + svsb = &svsp->banks[idx];
> + svsb->mts = mts;
> +
> + switch (svsb->sw_id) {
> + case SVSB_CPU_LITTLE:
> + tb_roomt = x_roomt[3];
> + break;
> + case SVSB_CPU_BIG:
> + tb_roomt = x_roomt[4];
> + break;
> + case SVSB_CCI:
> + tb_roomt = x_roomt[3];
> + break;
> + case SVSB_GPU:
> + tb_roomt = x_roomt[1];
> + break;
> + default:
> + break;
> + }
> +
> + temp0 = (tp.degc_cali * 10 / 2);
> + temp1 = ((10000 * 100000 / 4096 / tp.gain) *
> + tp.oe + tb_roomt * 10) * 15 / 18;
> +
> + if (!tp.o_slope_sign)
> + temp2 = temp1 * 100 / (1534 + tp.o_slope * 10);
> + else
> + temp2 = temp1 * 100 / (1534 - tp.o_slope * 10);
> +
> + svsb->bts = (temp0 + temp2 - 250) * 4 / 10;
> + }
> +
> + return true;
> +}
> +
> +static bool svs_is_supported(struct svs_platform *svsp)
> +{
> + struct nvmem_cell *cell;
> +
> + /* Get svs efuse by nvmem */
> + cell = nvmem_cell_get(svsp->dev, "svs-calibration-data");
> + if (IS_ERR_OR_NULL(cell)) {
> + dev_err(svsp->dev,
> + "no \"svs-calibration-data\" from dts? disable svs\n");
> + return false;
> + }
> +
> + svsp->efuse = (u32 *)nvmem_cell_read(cell, &svsp->efuse_num);
Similar to tefuse, I think efuse is only used at init time, so maybe
it ca be a local variable?
> + svsp->efuse_num /= sizeof(u32);
> + nvmem_cell_put(cell);
> +
> + if (!svsp->fake_efuse && !svsp->efuse[svsp->efuse_check]) {
> + dev_err(svsp->dev, "svs_efuse[%u] = 0x%x?\n",
> + svsp->efuse_check, svsp->efuse[svsp->efuse_check]);
> + return false;
> + }
> +
> + return svsp->efuse_parsing(svsp);
> +}
> +
> +static int svs_suspend(struct device *dev)
> +{
> + struct svs_platform *svsp = dev_get_drvdata(dev);
> + struct svs_bank *svsb;
> + unsigned long flags;
> + int ret;
> + u32 idx;
> +
> + for (idx = 0; idx < svsp->bank_num; idx++) {
> + svsb = &svsp->banks[idx];
> +
> + /* Wait if svs_isr() is still in process. */
> + spin_lock_irqsave(&mtk_svs_lock, flags);
> + svsp->pbank = svsb;
> + svs_switch_bank(svsp);
> + svs_writel(svsp, SVSB_EN_OFF, SVSEN);
> + svs_writel(svsp, SVSB_INTSTS_CLEAN, INTSTS);
> + spin_unlock_irqrestore(&mtk_svs_lock, flags);
> +
> + svsb->suspended = true;
> + if (svsb->phase != SVSB_PHASE_INIT01) {
> + svsb->phase = SVSB_PHASE_ERROR;
> + svs_adjust_pm_opp_volts(svsb, true);
> + }
> + }
> +
> + if (svsp->rst) {
> + ret = reset_control_assert(svsp->rst);
> + if (ret) {
> + dev_err(svsp->dev, "cannot assert reset %d\n", ret);
> + return ret;
> + }
> + }
> +
> + clk_disable_unprepare(svsp->main_clk);
> +
> + return 0;
> +}
> +
> +static int svs_resume(struct device *dev)
> +{
> + struct svs_platform *svsp = dev_get_drvdata(dev);
> + struct svs_bank *svsb;
> + int ret;
> + u32 idx;
> +
> + ret = clk_prepare_enable(svsp->main_clk);
> + if (ret) {
> + dev_err(svsp->dev, "cannot enable main_clk, disable svs\n");
> + return ret;
> + }
> +
> + if (svsp->rst) {
> + ret = reset_control_deassert(svsp->rst);
> + if (ret) {
> + dev_err(svsp->dev, "cannot deassert reset %d\n", ret);
> + return ret;
> + }
> + }
> +
> + for (idx = 0; idx < svsp->bank_num; idx++) {
> + svsb = &svsp->banks[idx];
> + svsb->suspended = false;
> + }
> +
> + ret = svs_init02(svsp);
> + if (ret)
> + return ret;
> +
> + svs_mon_mode(svsp);
> +
> + return 0;
> +}
> +
> +static struct svs_bank svs_mt8183_banks[4] = {
> + {
> + .sw_id = SVSB_CPU_LITTLE,
> + .cpu_id = 0,
> + .tzone_name = "tzts4",
> + .buck_name = "proc",
> + .pd_req = false,
> + .init01_volt_flag = SVSB_INIT01_VOLT_INC_ONLY,
> + .mode_support = SVSB_MODE_INIT01 | SVSB_MODE_INIT02,
> + .opp_count = 16,
> + .freq_base = 1989000000,
> + .vboot = 0x30,
> + .volt_step = 6250,
> + .volt_base = 500000,
> + .volt_offset = 0,
> + .vmax = 0x64,
> + .vmin = 0x18,
> + .dthi = 0x1,
> + .dtlo = 0xfe,
> + .det_window = 0xa28,
> + .det_max = 0xffff,
> + .age_config = 0x555555,
> + .agem = 0,
> + .dc_config = 0x555555,
> + .dvt_fixed = 0x7,
> + .vco = 0x10,
> + .chk_shift = 0x77,
> + .temp_upper_bound = 0x64,
> + .temp_lower_bound = 0xb2,
> + .tzone_high_temp = SVSB_TZONE_HIGH_TEMP_MAX,
> + .tzone_low_temp = 25000,
> + .tzone_low_temp_offset = 0,
> + .core_sel = 0x8fff0000,
> + .int_st = BIT(0),
> + .ctl0 = 0x00010001,
> + },
> + {
> + .sw_id = SVSB_CPU_BIG,
> + .cpu_id = 4,
> + .tzone_name = "tzts5",
> + .buck_name = "proc",
> + .pd_req = false,
> + .init01_volt_flag = SVSB_INIT01_VOLT_INC_ONLY,
> + .mode_support = SVSB_MODE_INIT01 | SVSB_MODE_INIT02,
> + .opp_count = 16,
> + .freq_base = 1989000000,
> + .vboot = 0x30,
> + .volt_step = 6250,
> + .volt_base = 500000,
> + .volt_offset = 0,
> + .vmax = 0x58,
> + .vmin = 0x10,
> + .dthi = 0x1,
> + .dtlo = 0xfe,
> + .det_window = 0xa28,
> + .det_max = 0xffff,
> + .age_config = 0x555555,
> + .agem = 0,
> + .dc_config = 0x555555,
> + .dvt_fixed = 0x7,
> + .vco = 0x10,
> + .chk_shift = 0x77,
> + .temp_upper_bound = 0x64,
> + .temp_lower_bound = 0xb2,
> + .tzone_high_temp = SVSB_TZONE_HIGH_TEMP_MAX,
> + .tzone_low_temp = 25000,
> + .tzone_low_temp_offset = 0,
> + .core_sel = 0x8fff0001,
> + .int_st = BIT(1),
> + .ctl0 = 0x00000001,
> + },
> + {
> + .sw_id = SVSB_CCI,
> + .tzone_name = "tzts4",
> + .buck_name = "proc",
> + .pd_req = false,
> + .init01_volt_flag = SVSB_INIT01_VOLT_INC_ONLY,
> + .mode_support = SVSB_MODE_INIT01 | SVSB_MODE_INIT02,
> + .opp_count = 16,
> + .freq_base = 1196000000,
> + .vboot = 0x30,
> + .volt_step = 6250,
> + .volt_base = 500000,
> + .volt_offset = 0,
> + .vmax = 0x64,
> + .vmin = 0x18,
> + .dthi = 0x1,
> + .dtlo = 0xfe,
> + .det_window = 0xa28,
> + .det_max = 0xffff,
> + .age_config = 0x555555,
> + .agem = 0,
> + .dc_config = 0x555555,
> + .dvt_fixed = 0x7,
> + .vco = 0x10,
> + .chk_shift = 0x77,
> + .temp_upper_bound = 0x64,
> + .temp_lower_bound = 0xb2,
> + .tzone_high_temp = SVSB_TZONE_HIGH_TEMP_MAX,
> + .tzone_low_temp = 25000,
> + .tzone_low_temp_offset = 0,
> + .core_sel = 0x8fff0002,
> + .int_st = BIT(2),
> + .ctl0 = 0x00100003,
> + },
> + {
> + .sw_id = SVSB_GPU,
> + .tzone_name = "tzts2",
> + .buck_name = "mali",
> + .pd_req = true,
> + .init01_volt_flag = SVSB_INIT01_VOLT_INC_ONLY,
> + .mode_support = SVSB_MODE_INIT01 | SVSB_MODE_INIT02 |
> + SVSB_MODE_MON,
> + .opp_count = 16,
> + .freq_base = 900000000,
> + .vboot = 0x30,
> + .volt_step = 6250,
> + .volt_base = 500000,
> + .volt_offset = 0,
> + .vmax = 0x40,
> + .vmin = 0x14,
> + .dthi = 0x1,
> + .dtlo = 0xfe,
> + .det_window = 0xa28,
> + .det_max = 0xffff,
> + .age_config = 0x555555,
> + .agem = 0,
> + .dc_config = 0x555555,
> + .dvt_fixed = 0x3,
> + .vco = 0x10,
> + .chk_shift = 0x77,
> + .temp_upper_bound = 0x64,
> + .temp_lower_bound = 0xb2,
> + .tzone_high_temp = SVSB_TZONE_HIGH_TEMP_MAX,
> + .tzone_low_temp = 25000,
> + .tzone_low_temp_offset = 3,
> + .core_sel = 0x8fff0003,
> + .int_st = BIT(3),
> + .ctl0 = 0x00050001,
> + },
> +};
> +
> +static int svs_get_svs_mt8183_platform_data(struct svs_platform *svsp)
> +{
> + struct device *dev;
> + struct svs_bank *svsb;
> + u32 idx;
> +
> + svsp->name = "mt8183-svs";
> + svsp->banks = svs_mt8183_banks;
> + svsp->efuse_parsing = svs_mt8183_efuse_parsing;
> + svsp->set_freqs_pct = svs_set_freqs_pct_v2;
> + svsp->get_vops = svs_get_vops_v2;
> + svsp->regs = svs_regs_v2;
> + svsp->irqflags = IRQF_TRIGGER_LOW | IRQF_ONESHOT;
> + svsp->rst = NULL;
> + svsp->fake_efuse = false;
> + svsp->bank_num = 4;
> + svsp->efuse_check = 2;
> +
> + dev = svs_add_device_link(svsp, "thermal");
> + if (IS_ERR(dev))
> + return PTR_ERR(dev);
> +
> + for (idx = 0; idx < svsp->bank_num; idx++) {
> + svsb = &svsp->banks[idx];
> +
> + switch (svsb->sw_id) {
> + case SVSB_CPU_LITTLE:
> + case SVSB_CPU_BIG:
> + svsb->opp_dev = get_cpu_device(svsb->cpu_id);
> + break;
> + case SVSB_CCI:
> + svsb->opp_dev = svs_add_device_link(svsp, "cci");
> + break;
> + case SVSB_GPU:
> + svsb->opp_dev = svs_add_device_link(svsp, "mali");
> + svsb->pd_dev = svs_add_device_link(svsp,
> + "mali_gpu_core2");
> + if (IS_ERR(svsb->pd_dev))
> + return PTR_ERR(svsb->pd_dev);
> + break;
> + default:
> + WARN_ON(1);
> + return -EINVAL;
> + }
> +
> + if (IS_ERR(svsb->opp_dev))
> + return PTR_ERR(svsb->opp_dev);
> + }
> +
> + return 0;
> +}
> +
> +static const struct of_device_id mtk_svs_of_match[] = {
> + {
> + .compatible = "mediatek,mt8183-svs",
> + .data = &svs_get_svs_mt8183_platform_data,
> + }, {
> + /* Sentinel */
> + },
> +};
> +
> +static int svs_probe(struct platform_device *pdev)
> +{
> + int (*svs_get_svs_platform_data)(struct svs_platform *svsp);
> + struct svs_platform *svsp;
> + unsigned int svsp_irq;
> + int ret;
> +
> + svsp = devm_kzalloc(&pdev->dev, sizeof(*svsp), GFP_KERNEL);
> + if (!svsp)
> + return -ENOMEM;
> +
> + svs_get_svs_platform_data = of_device_get_match_data(&pdev->dev);
> + if (!svs_get_svs_platform_data) {
> + dev_err(svsp->dev, "no svs platform data? why?\n");
> + return -EPERM;
> + }
> +
> + svsp->dev = &pdev->dev;
> + ret = svs_get_svs_platform_data(svsp);
> + if (ret) {
> + dev_err_probe(svsp->dev, ret, "fail to get svsp data\n");
> + return ret;
> + }
> +
> + if (!svs_is_supported(svsp)) {
> + dev_notice(svsp->dev, "svs is not supported\n");
> + return -EPERM;
> + }
> +
> + ret = svs_resource_setup(svsp);
> + if (ret) {
> + dev_err(svsp->dev, "svs resource setup fail: %d\n", ret);
> + return ret;
> + }
> +
> + svsp_irq = irq_of_parse_and_map(svsp->dev->of_node, 0);
> + ret = devm_request_threaded_irq(svsp->dev, svsp_irq, NULL, svs_isr,
> + svsp->irqflags, svsp->name, svsp);
> + if (ret) {
> + dev_err(svsp->dev, "register irq(%d) failed: %d\n",
> + svsp_irq, ret);
> + return ret;
> + }
> +
> + svsp->main_clk = devm_clk_get(svsp->dev, "main");
> + if (IS_ERR(svsp->main_clk)) {
> + dev_err(svsp->dev, "failed to get clock: %ld\n",
> + PTR_ERR(svsp->main_clk));
> + return PTR_ERR(svsp->main_clk);
> + }
> +
> + ret = clk_prepare_enable(svsp->main_clk);
> + if (ret) {
> + dev_err(svsp->dev, "cannot enable main clk: %d\n", ret);
> + return ret;
> + }
> +
> + svsp->base = of_iomap(svsp->dev->of_node, 0);
> + if (IS_ERR_OR_NULL(svsp->base)) {
> + dev_err(svsp->dev, "cannot find svs register base\n");
> + ret = -EINVAL;
> + goto svs_probe_clk_disable;
> + }
> +
> + ret = svs_start(svsp);
> + if (ret) {
> + dev_err(svsp->dev, "svs start fail: %d\n", ret);
> + goto svs_probe_iounmap;
> + }
> +
> + return 0;
> +
> +svs_probe_iounmap:
> + iounmap(svsp->base);
> +
> +svs_probe_clk_disable:
> + clk_disable_unprepare(svsp->main_clk);
> +
> + return ret;
> +}
> +
> +static SIMPLE_DEV_PM_OPS(svs_pm_ops, svs_suspend, svs_resume);
> +
> +static struct platform_driver svs_driver = {
> + .probe = svs_probe,
> + .driver = {
> + .name = "mtk-svs",
> + .pm = &svs_pm_ops,
> + .of_match_table = of_match_ptr(mtk_svs_of_match),
> + },
> +};
> +
> +module_platform_driver(svs_driver);
> +
> +MODULE_AUTHOR("Roger Lu <roger.lu at mediatek.com>");
> +MODULE_DESCRIPTION("MediaTek SVS driver");
> +MODULE_LICENSE("GPL v2");
> --
> 2.18.0
> _______________________________________________
> Linux-mediatek mailing list
> Linux-mediatek at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-mediatek
More information about the Linux-mediatek
mailing list