[PATCH v2] scsi: ufs: Remove pre-defined initial voltage values of device powers

[nguyenb at codeaurora.org]

On 2020-11-30 22:51, Stanley Chu wrote:
> UFS specficication allows different VCC configurations for UFS devices,
> for example,
> 	(1). 2.70V - 3.60V (Activated by default in UFS core driver)
> 	(2). 1.70V - 1.95V (Activated if "vcc-supply-1p8" is declared in
>                           device tree)
> 	(3). 2.40V - 2.70V (Supported since UFS 3.x)
> 
> With the introduction of UFS 3.x products, an issue is happening that
> UFS driver will use wrong "min_uV-max_uV" values to configure the
> voltage of VCC regulator on UFU 3.x products with the configuration (3)
> used.
> 
> To solve this issue, we simply remove pre-defined initial VCC voltage
> values in UFS core driver with below reasons,
> 
> 1. UFS specifications do not define how to detect the VCC configuration
>    supported by attached device.
> 
> 2. Device tree already supports standard regulator properties.
> 
> Therefore VCC voltage shall be defined correctly in device tree, and
> shall not changed by UFS driver. What UFS driver needs to do is simply
> enable or disable the VCC regulator only.
> 
> Similar change is applied to VCCQ and VCCQ2 as well.
> 
> Note that we keep struct ufs_vreg unchanged. This is allow vendors to
> configure proper min_uV and max_uV of any regulators to make
> regulator_set_voltage() works during regulator toggling flow.
> Without specific vendor configurations, min_uV and max_uV will be NULL
> by default and UFS core driver will enable or disable the regulator
> only without adjusting its voltage.
> 
> Reviewed-by: Bjorn Andersson <bjorn.andersson at linaro.org>
> Signed-off-by: Stanley Chu <stanley.chu at mediatek.com>
> ---
>  drivers/scsi/ufs/ufshcd-pltfrm.c | 16 ----------------
>  1 file changed, 16 deletions(-)
> 
> diff --git a/drivers/scsi/ufs/ufshcd-pltfrm.c 
> b/drivers/scsi/ufs/ufshcd-pltfrm.c
> index a6f76399b3ae..09e2f04bf4f6 100644
> --- a/drivers/scsi/ufs/ufshcd-pltfrm.c
> +++ b/drivers/scsi/ufs/ufshcd-pltfrm.c
> @@ -133,22 +133,6 @@ static int ufshcd_populate_vreg(struct device
> *dev, const char *name,
>  		vreg->max_uA = 0;
>  	}
> 
> -	if (!strcmp(name, "vcc")) {
> -		if (of_property_read_bool(np, "vcc-supply-1p8")) {
> -			vreg->min_uV = UFS_VREG_VCC_1P8_MIN_UV;
> -			vreg->max_uV = UFS_VREG_VCC_1P8_MAX_UV;
> -		} else {
> -			vreg->min_uV = UFS_VREG_VCC_MIN_UV;
> -			vreg->max_uV = UFS_VREG_VCC_MAX_UV;
> -		}
> -	} else if (!strcmp(name, "vccq")) {
> -		vreg->min_uV = UFS_VREG_VCCQ_MIN_UV;
> -		vreg->max_uV = UFS_VREG_VCCQ_MAX_UV;
> -	} else if (!strcmp(name, "vccq2")) {
> -		vreg->min_uV = UFS_VREG_VCCQ2_MIN_UV;
> -		vreg->max_uV = UFS_VREG_VCCQ2_MAX_UV;
> -	}
> -
>  	goto out;
Do we need this "goto out;"?

> 
>  out: