[PATCH v2 4/4] pintcrl: support bias-disable of generic and special pins simultaneously

Zhiyong Tao zhiyong.tao at mediatek.com
Tue Feb 27 23:49:17 PST 2018


On Wed, 2018-02-28 at 15:33 +0800, Sean Wang wrote:
> On Mon, 2018-02-26 at 16:34 +0800, Zhiyong Tao wrote:
> > For generic pins, parameter "arg" is 0 or 1.
> > For special pins, bias-disable is set by R0R1,
> > so we need transmited "00" to set bias-disable
> > When we set "bias-disable" as high-z property,
> > the parameter should be "MTK_PUPD_SET_R1R0_00".
> > 
> > Signed-off-by: Zhiyong Tao <zhiyong.tao at mediatek.com>
> > ---
> >  drivers/pinctrl/mediatek/pinctrl-mtk-common.c | 13 +++++++++++--
> >  1 file changed, 11 insertions(+), 2 deletions(-)
> > 
> > diff --git a/drivers/pinctrl/mediatek/pinctrl-mtk-common.c b/drivers/pinctrl/mediatek/pinctrl-mtk-common.c
> > index 3cf384f..e88ba04 100644
> > --- a/drivers/pinctrl/mediatek/pinctrl-mtk-common.c
> > +++ b/drivers/pinctrl/mediatek/pinctrl-mtk-common.c
> > @@ -301,8 +301,17 @@ static int mtk_pconf_set_pull_select(struct mtk_pinctrl *pctl,
> >  	 * resistor bit, so we need this special handle.
> >  	 */
> >  	if (pctl->devdata->spec_pull_set) {
> > -		ret = pctl->devdata->spec_pull_set(mtk_get_regmap(pctl, pin),
> > -			pin, pctl->devdata->port_align, isup, arg);
> > +		if (enable) {
> > +			ret = pctl->devdata->spec_pull_set(
> > +				mtk_get_regmap(pctl, pin), pin,
> > +				pctl->devdata->port_align, isup,
> > +				arg);
> > +		} else {
> > +			ret = pctl->devdata->spec_pull_set(
> > +				mtk_get_regmap(pctl, pin), pin,
> > +				pctl->devdata->port_align, isup,
> > +				MTK_PUPD_SET_R1R0_00);
> > +		}
> 
> 
> it looks like you can use as following snippet with reusing original
> logic and less effort on maintaining these common code (?)
==> Thanks for your suggestion very much. It seems better.
I will change it in v3.
> 
> 
> if (pctl->devdata->spec_pull_set) {
> 	+ if (!enable)
> 	+ 	arg = MTK_PUPD_SET_R1R0_00;
> 
> 	ret = pctl->devdata->spec_pull_set(mtk_get_regmap(pctl, pin),
> 		pin, pctl->devdata->port_align, isup, arg);
> 
> 
> Also, it's better to add more comments to such kind of special path for
> allowing future SoCs to follow and extend more easily.

==> Thanks for your suggestion very much. I will add more comments here.
> 
> >  		if (!ret)
> >  			return 0;
> >  	}
> 
> 





More information about the Linux-mediatek mailing list