[PATCH v1 11/19] arm: dts: mt7623: use - instead of _ in DT node name
sean.wang at mediatek.com
sean.wang at mediatek.com
Fri Feb 23 02:16:31 PST 2018
From: Sean Wang <sean.wang at mediatek.com>
It should be good that no use "_" is in DT node name. Consequently,
those nodes in certain files which have an inappropriate name containing
"_" are all being replaced with "-".
Signed-off-by: Sean Wang <sean.wang at mediatek.com>
Cc: Rob Herring <robh+dt at kernel.org>
Cc: Mark Rutland <mark.rutland at arm.com>
Cc: devicetree at vger.kernel.org
---
arch/arm/boot/dts/mt7623.dtsi | 12 +++----
arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts | 50 +++++++++++++--------------
arch/arm/boot/dts/mt7623n-rfb-nand.dts | 6 ++--
3 files changed, 34 insertions(+), 34 deletions(-)
diff --git a/arch/arm/boot/dts/mt7623.dtsi b/arch/arm/boot/dts/mt7623.dtsi
index 5cf93a4..4b68448 100644
--- a/arch/arm/boot/dts/mt7623.dtsi
+++ b/arch/arm/boot/dts/mt7623.dtsi
@@ -28,7 +28,7 @@
compatible = "mediatek,mt7623";
interrupt-parent = <&sysirq>;
- cpu_opp_table: opp_table {
+ cpu_opp_table: opp-table {
compatible = "operating-points-v2";
opp-shared;
@@ -145,32 +145,32 @@
};
thermal-zones {
- cpu_thermal: cpu_thermal {
+ cpu_thermal: cpu-thermal {
polling-delay-passive = <1000>;
polling-delay = <1000>;
thermal-sensors = <&thermal 0>;
trips {
- cpu_passive: cpu_passive {
+ cpu_passive: cpu-passive {
temperature = <47000>;
hysteresis = <2000>;
type = "passive";
};
- cpu_active: cpu_active {
+ cpu_active: cpu-active {
temperature = <67000>;
hysteresis = <2000>;
type = "active";
};
- cpu_hot: cpu_hot {
+ cpu_hot: cpu-hot {
temperature = <87000>;
hysteresis = <2000>;
type = "hot";
};
- cpu_crit {
+ cpu-crit {
temperature = <107000>;
hysteresis = <2000>;
type = "critical";
diff --git a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
index f2d3cfb..a6295ef 100644
--- a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
+++ b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
@@ -66,7 +66,7 @@
regulator-always-on;
};
- gpio_keys {
+ gpio-keys {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&key_pins_a>;
@@ -263,14 +263,14 @@
&pio {
cir_pins_a:cir at 0 {
- pins_cir {
+ pins-cir {
pinmux = <MT7623_PIN_46_IR_FUNC_IR>;
bias-disable;
};
};
i2c0_pins_a: i2c at 0 {
- pins_i2c0 {
+ pins-i2c0 {
pinmux = <MT7623_PIN_75_SDA0_FUNC_SDA0>,
<MT7623_PIN_76_SCL0_FUNC_SCL0>;
bias-disable;
@@ -278,7 +278,7 @@
};
i2c1_pins_a: i2c at 1 {
- pin_i2c1 {
+ pin-i2c1 {
pinmux = <MT7623_PIN_57_SDA1_FUNC_SDA1>,
<MT7623_PIN_58_SCL1_FUNC_SCL1>;
bias-disable;
@@ -286,7 +286,7 @@
};
i2s0_pins_a: i2s at 0 {
- pin_i2s0 {
+ pin-i2s0 {
pinmux = <MT7623_PIN_49_I2S0_DATA_FUNC_I2S0_DATA>,
<MT7623_PIN_72_I2S0_DATA_IN_FUNC_I2S0_DATA_IN>,
<MT7623_PIN_73_I2S0_LRCK_FUNC_I2S0_LRCK>,
@@ -298,7 +298,7 @@
};
i2s1_pins_a: i2s at 1 {
- pin_i2s1 {
+ pin-i2s1 {
pinmux = <MT7623_PIN_33_I2S1_DATA_FUNC_I2S1_DATA>,
<MT7623_PIN_34_I2S1_DATA_IN_FUNC_I2S1_DATA_IN>,
<MT7623_PIN_35_I2S1_BCK_FUNC_I2S1_BCK>,
@@ -310,7 +310,7 @@
};
key_pins_a: keys at 0 {
- pins_keys {
+ pins-keys {
pinmux = <MT7623_PIN_256_GPIO256_FUNC_GPIO256>,
<MT7623_PIN_257_GPIO257_FUNC_GPIO257> ;
input-enable;
@@ -318,7 +318,7 @@
};
led_pins_a: leds at 0 {
- pins_leds {
+ pins-leds {
pinmux = <MT7623_PIN_239_EXT_SDIO0_FUNC_GPIO239>,
<MT7623_PIN_240_EXT_XCS_FUNC_GPIO240>,
<MT7623_PIN_241_EXT_SCK_FUNC_GPIO241>;
@@ -326,7 +326,7 @@
};
mmc0_pins_default: mmc0default {
- pins_cmd_dat {
+ pins-cmd-dat {
pinmux = <MT7623_PIN_111_MSDC0_DAT7_FUNC_MSDC0_DAT7>,
<MT7623_PIN_112_MSDC0_DAT6_FUNC_MSDC0_DAT6>,
<MT7623_PIN_113_MSDC0_DAT5_FUNC_MSDC0_DAT5>,
@@ -340,19 +340,19 @@
bias-pull-up;
};
- pins_clk {
+ pins-clk {
pinmux = <MT7623_PIN_117_MSDC0_CLK_FUNC_MSDC0_CLK>;
bias-pull-down;
};
- pins_rst {
+ pins-rst {
pinmux = <MT7623_PIN_115_MSDC0_RSTB_FUNC_MSDC0_RSTB>;
bias-pull-up;
};
};
mmc0_pins_uhs: mmc0 {
- pins_cmd_dat {
+ pins-cmd-dat {
pinmux = <MT7623_PIN_111_MSDC0_DAT7_FUNC_MSDC0_DAT7>,
<MT7623_PIN_112_MSDC0_DAT6_FUNC_MSDC0_DAT6>,
<MT7623_PIN_113_MSDC0_DAT5_FUNC_MSDC0_DAT5>,
@@ -367,20 +367,20 @@
bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
};
- pins_clk {
+ pins-clk {
pinmux = <MT7623_PIN_117_MSDC0_CLK_FUNC_MSDC0_CLK>;
drive-strength = <MTK_DRIVE_2mA>;
bias-pull-down = <MTK_PUPD_SET_R1R0_01>;
};
- pins_rst {
+ pins-rst {
pinmux = <MT7623_PIN_115_MSDC0_RSTB_FUNC_MSDC0_RSTB>;
bias-pull-up;
};
};
mmc1_pins_default: mmc1default {
- pins_cmd_dat {
+ pins-cmd-dat {
pinmux = <MT7623_PIN_107_MSDC1_DAT0_FUNC_MSDC1_DAT0>,
<MT7623_PIN_108_MSDC1_DAT1_FUNC_MSDC1_DAT1>,
<MT7623_PIN_109_MSDC1_DAT2_FUNC_MSDC1_DAT2>,
@@ -391,26 +391,26 @@
bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
};
- pins_clk {
+ pins-clk {
pinmux = <MT7623_PIN_106_MSDC1_CLK_FUNC_MSDC1_CLK>;
bias-pull-down;
drive-strength = <MTK_DRIVE_4mA>;
};
- pins_wp {
+ pins-wp {
pinmux = <MT7623_PIN_29_EINT7_FUNC_MSDC1_WP>;
input-enable;
bias-pull-up;
};
- pins_insert {
+ pins-insert {
pinmux = <MT7623_PIN_261_MSDC1_INS_FUNC_GPIO261>;
bias-pull-up;
};
};
mmc1_pins_uhs: mmc1 {
- pins_cmd_dat {
+ pins-cmd-dat {
pinmux = <MT7623_PIN_107_MSDC1_DAT0_FUNC_MSDC1_DAT0>,
<MT7623_PIN_108_MSDC1_DAT1_FUNC_MSDC1_DAT1>,
<MT7623_PIN_109_MSDC1_DAT2_FUNC_MSDC1_DAT2>,
@@ -421,7 +421,7 @@
bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
};
- pins_clk {
+ pins-clk {
pinmux = <MT7623_PIN_106_MSDC1_CLK_FUNC_MSDC1_CLK>;
drive-strength = <MTK_DRIVE_4mA>;
bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
@@ -437,7 +437,7 @@
};
pwm_pins_a: pwm at 0 {
- pins_pwm {
+ pins-pwm {
pinmux = <MT7623_PIN_203_PWM0_FUNC_PWM0>,
<MT7623_PIN_204_PWM1_FUNC_PWM1>,
<MT7623_PIN_205_PWM2_FUNC_PWM2>,
@@ -447,7 +447,7 @@
};
spi0_pins_a: spi at 0 {
- pins_spi {
+ pins-spi {
pinmux = <MT7623_PIN_53_SPI0_CSN_FUNC_SPI0_CS>,
<MT7623_PIN_54_SPI0_CK_FUNC_SPI0_CK>,
<MT7623_PIN_55_SPI0_MI_FUNC_SPI0_MI>,
@@ -457,21 +457,21 @@
};
uart0_pins_a: uart at 0 {
- pins_dat {
+ pins-dat {
pinmux = <MT7623_PIN_79_URXD0_FUNC_URXD0>,
<MT7623_PIN_80_UTXD0_FUNC_UTXD0>;
};
};
uart1_pins_a: uart at 1 {
- pins_dat {
+ pins-dat {
pinmux = <MT7623_PIN_81_URXD1_FUNC_URXD1>,
<MT7623_PIN_82_UTXD1_FUNC_UTXD1>;
};
};
uart2_pins_a: uart at 2 {
- pins_dat {
+ pins-dat {
pinmux = <MT7623_PIN_14_GPIO14_FUNC_URXD2>,
<MT7623_PIN_15_GPIO15_FUNC_UTXD2>;
};
diff --git a/arch/arm/boot/dts/mt7623n-rfb-nand.dts b/arch/arm/boot/dts/mt7623n-rfb-nand.dts
index e66de86..f729c71 100644
--- a/arch/arm/boot/dts/mt7623n-rfb-nand.dts
+++ b/arch/arm/boot/dts/mt7623n-rfb-nand.dts
@@ -81,13 +81,13 @@
&pio {
nand_pins_default: nanddefault {
- pins_ale {
+ pins-ale {
pinmux = <MT7623_PIN_116_MSDC0_CMD_FUNC_NALE>;
drive-strength = <MTK_DRIVE_8mA>;
bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
};
- pins_dat {
+ pins-dat {
pinmux = <MT7623_PIN_111_MSDC0_DAT7_FUNC_NLD7>,
<MT7623_PIN_112_MSDC0_DAT6_FUNC_NLD6>,
<MT7623_PIN_114_MSDC0_DAT4_FUNC_NLD4>,
@@ -102,7 +102,7 @@
bias-pull-up;
};
- pins_we {
+ pins-we {
pinmux = <MT7623_PIN_117_MSDC0_CLK_FUNC_NWEB>;
drive-strength = <MTK_DRIVE_8mA>;
bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
--
2.7.4
More information about the Linux-mediatek
mailing list