[PATCH v2 2/2] soc: mediatek: add a fixed wait for SRAM stable
Matthias Brugger
matthias.bgg at gmail.com
Fri Apr 27 02:46:14 PDT 2018
Hi Sean,
On 04/23/2018 11:39 AM, Sean Wang wrote:
> On Mon, 2018-04-23 at 11:31 +0200, Matthias Brugger wrote:
>>
>> On 04/23/2018 10:36 AM, sean.wang at mediatek.com wrote:
>>> From: Sean Wang <sean.wang at mediatek.com>
>>>
>>> MT7622_POWER_DOMAIN_WB doesn't send an ACK when its managed SRAM becomes
>>> stable, which is not like the behavior the other power domains should
>>> have. Therefore, it's necessary for such a power domain to have a fixed
>>> and well-predefined duration to wait until its managed SRAM can be allowed
>>> to access by all functions running on the top.
>>>
>>> v1 -> v2:
>>> - use MTK_SCPD_FWAIT_SRAM flag as an indication requiring force waiting.
>>>
>>> Signed-off-by: Sean Wang <sean.wang at mediatek.com>
>>> Cc: Matthias Brugger <matthias.bgg at gmail.com>
>>> Cc: Ulf Hansson <ulf.hansson at linaro.org>
>>> Cc: Weiyi Lu <weiyi.lu at mediatek.com>
>>> ---
>>> drivers/soc/mediatek/mtk-scpsys.c | 24 ++++++++++++++++++------
>>> 1 file changed, 18 insertions(+), 6 deletions(-)
>>>
>>> diff --git a/drivers/soc/mediatek/mtk-scpsys.c b/drivers/soc/mediatek/mtk-scpsys.c
>>> index b1b45e4..d4f1a63 100644
>>> --- a/drivers/soc/mediatek/mtk-scpsys.c
>>> +++ b/drivers/soc/mediatek/mtk-scpsys.c
>>> @@ -32,6 +32,7 @@
>>> #define MTK_POLL_TIMEOUT (jiffies_to_usecs(HZ))
>>>
>>> #define MTK_SCPD_ACTIVE_WAKEUP BIT(0)
>>> +#define MTK_SCPD_FWAIT_SRAM BIT(1)
>>> #define MTK_SCPD_CAPS(_scpd, _x) ((_scpd)->data->caps & (_x))
>>>
>>> #define SPM_VDE_PWR_CON 0x0210
>>> @@ -237,11 +238,22 @@ static int scpsys_power_on(struct generic_pm_domain *genpd)
>>> val &= ~scpd->data->sram_pdn_bits;
>>> writel(val, ctl_addr);
>>>
>>> - /* wait until SRAM_PDN_ACK all 0 */
>>> - ret = readl_poll_timeout(ctl_addr, tmp, (tmp & pdn_ack) == 0,
>>> - MTK_POLL_DELAY_US, MTK_POLL_TIMEOUT);
>>> - if (ret < 0)
>>> - goto err_pwr_ack;
>>> + /* Either wait until SRAM_PDN_ACK all 0 or have a force wait */
>>> + if (!MTK_SCPD_CAPS(scpd, MTK_SCPD_FWAIT_SRAM)) {
After having another look on the patch, could you change the order of the if:
So that we check for the existence of the MTK_SCPD_FWAIT_SRAM and sleep and in
the else branch we to the readl_poll_timeout.
I think in the future this will make the code easier to understand as you can
easily oversee the '!' negation in the if.
Regards,
Matthias
>>> + ret = readl_poll_timeout(ctl_addr, tmp, (tmp & pdn_ack) == 0,
>>> + MTK_POLL_DELAY_US, MTK_POLL_TIMEOUT);
>>> + if (ret < 0)
>>> + goto err_pwr_ack;
>>> + } else {
>>> + /*
>>> + * Currently, MTK_SCPD_FWAIT_SRAM is necessary only for
>>> + * MT7622_POWER_DOMAIN_WB and thus just a trivial setup is
>>> + * applied here. If there're more domains which need to force
>>> + * waiting for its own pre-defined value, the duration should
>>> + * be coded in the caps field.
>>> + */
>>
>> I would say, if necessary in the future we can add a switch statement here.
>> Other then that the patches look good. If you are OK, I'll just delete the last
>> sentence when applying the patch.
>>
>
> yes, it's okay for me.
>
>> Regards,
>> Matthias
>>
>>> + usleep_range(12000, 12100);
>>> + };
>>>
>>> if (scpd->data->bus_prot_mask) {
>>> ret = mtk_infracfg_clear_bus_protection(scp->infracfg,
>>> @@ -785,7 +797,7 @@ static const struct scp_domain_data scp_domain_data_mt7622[] = {
>>> .sram_pdn_ack_bits = 0,
>>> .clk_id = {CLK_NONE},
>>> .bus_prot_mask = MT7622_TOP_AXI_PROT_EN_WB,
>>> - .caps = MTK_SCPD_ACTIVE_WAKEUP,
>>> + .caps = MTK_SCPD_ACTIVE_WAKEUP | MTK_SCPD_FWAIT_SRAM,
>>> },
>>> };
>>>
>>>
>
>
More information about the Linux-mediatek
mailing list