[RFC 02/12] mtd: nand: force drivers to explicitly send READ/PROG commands
Stefan Agner
stefan at agner.ch
Fri Oct 20 02:29:18 PDT 2017
Hi Miquel,
Thanks for the work on this, happy to see the new interface is moving
forward. Some comments below.
On 2017-10-18 16:36, Miquel Raynal wrote:
> From: Boris Brezillon <boris.brezillon at free-electrons.com>
>
> The core currently send the READ0 and SEQIN+PAGEPROG commands in
> nand_do_read/write_ops(). This is inconsistent with
> ->read/write_oob[_raw]() hooks behavior which are expected to send
> these commands.
>
> There's already a flag (NAND_ECC_CUSTOM_PAGE_ACCESS) to inform the core
> that a specific controller wants to send the READ/SEQIN+PAGEPROG
> commands on its own, but it's an opt-in flag, and existing drivers are
> unlikely to be updated to pass it.
>
> Moreover, some controllers cannot dissociate the READ/PAGEPROG commands
> from the associated data transfer and ECC engine activation, and
> developers have to hack things in their ->cmdfunc() implementation to
> handle such complex cases, or have to accept the perf penalty of sending
> twice the same command.
> To address this problem we are planning on adding a new interface which
> is passed all information about a NAND operation (including the amount
> of data to transfer) and replacing all calls to ->cmdfunc() to calls to
> this new ->exec_op() hook. But, in order to do that, we need to have all
> ->cmdfunc() calls placed near their associated ->read/write_buf/byte()
> calls.
>
> Modify the core and relevant drivers to make NAND_ECC_CUSTOM_PAGE_ACCESS
> the default case, and remove this flag.
>
> Signed-off-by: Boris Brezillon <boris.brezillon at free-electrons.com>
> [miquel.raynal at free-electrons.com: rebased and fixed some conflicts]
> Signed-off-by: Miquel Raynal <miquel.raynal at free-electrons.com>
> ---
> drivers/mtd/nand/atmel/nand-controller.c | 7 ++-
> drivers/mtd/nand/bf5xx_nand.c | 6 ++-
> drivers/mtd/nand/brcmnand/brcmnand.c | 13 +++--
> drivers/mtd/nand/cafe_nand.c | 6 +--
> drivers/mtd/nand/denali.c | 14 +++++-
> drivers/mtd/nand/docg4.c | 12 +++--
> drivers/mtd/nand/fsl_elbc_nand.c | 6 +--
> drivers/mtd/nand/fsl_ifc_nand.c | 6 +--
> drivers/mtd/nand/gpmi-nand/gpmi-nand.c | 30 ++++++------
> drivers/mtd/nand/hisi504_nand.c | 6 +--
> drivers/mtd/nand/lpc32xx_mlc.c | 5 +-
> drivers/mtd/nand/lpc32xx_slc.c | 11 +++--
> drivers/mtd/nand/mtk_nand.c | 10 ++--
> drivers/mtd/nand/nand_base.c | 68 +++++++++------------------
> drivers/mtd/nand/nand_micron.c | 1 -
> drivers/mtd/nand/sh_flctl.c | 6 +--
> drivers/mtd/nand/sunxi_nand.c | 34 +++++++++-----
> drivers/mtd/nand/tango_nand.c | 1 -
> drivers/mtd/nand/vf610_nfc.c | 6 +--
> drivers/staging/mt29f_spinand/mt29f_spinand.c | 7 ++-
> include/linux/mtd/rawnand.h | 11 -----
> 21 files changed, 142 insertions(+), 124 deletions(-)
>
<snip>
> diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c
> b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c
> index c8ceaecd8065..3f2b903158c1 100644
> --- a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c
> +++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c
> @@ -1043,6 +1043,8 @@ static int gpmi_ecc_read_page(struct mtd_info
> *mtd, struct nand_chip *chip,
> unsigned int max_bitflips = 0;
> int ret;
>
> + nand_read_page_op(chip, page, 0, NULL, 0);
> +
> dev_dbg(this->dev, "page number is : %d\n", page);
> ret = read_page_prepare(this, buf, nfc_geo->payload_size,
> this->payload_virt, this->payload_phys,
> @@ -1220,12 +1222,13 @@ static int gpmi_ecc_read_subpage(struct
> mtd_info *mtd, struct nand_chip *chip,
> meta = geo->metadata_size;
> if (first) {
> col = meta + (size + ecc_parity_size) * first;
> - chip->cmdfunc(mtd, NAND_CMD_RNDOUT, col, -1);
Shouldn't we add nand_change_read_column_op here?
>
> meta = 0;
> buf = buf + first * size;
> }
>
> + nand_read_page_op(chip, page, col, NULL, 0);
> +
> /* Save the old environment */
> r1_old = r1_new = readl(bch_regs + HW_BCH_FLASH0LAYOUT0);
> r2_old = r2_new = readl(bch_regs + HW_BCH_FLASH0LAYOUT1);
> @@ -1277,6 +1280,9 @@ static int gpmi_ecc_write_page(struct mtd_info
> *mtd, struct nand_chip *chip,
> int ret;
>
> dev_dbg(this->dev, "ecc write page.\n");
> +
> + nand_prog_page_begin_op(chip, page, 0, NULL, 0);
> +
> if (this->swap_block_mark) {
> /*
> * If control arrives here, we're doing block mark swapping.
> @@ -1338,7 +1344,10 @@ static int gpmi_ecc_write_page(struct mtd_info
> *mtd, struct nand_chip *chip,
> payload_virt, payload_phys);
> }
>
> - return 0;
> + if (ret)
> + return ret;
> +
> + return nand_prog_page_end_op(chip);
> }
>
> /*
> @@ -1472,8 +1481,8 @@ static int gpmi_ecc_read_page_raw(struct mtd_info *mtd,
> uint8_t *oob = chip->oob_poi;
> int step;
>
> - chip->read_buf(mtd, tmp_buf,
> - mtd->writesize + mtd->oobsize);
> + nand_read_page_op(chip, page, 0, tmp_buf,
> + mtd->writesize + mtd->oobsize);
>
> /*
> * If required, swap the bad block marker and the data stored in the
> @@ -1617,24 +1626,19 @@ static int gpmi_ecc_write_page_raw(struct mtd_info *mtd,
> tmp_buf[mtd->writesize] = swap;
> }
>
> - chip->write_buf(mtd, tmp_buf, mtd->writesize + mtd->oobsize);
> -
> - return 0;
> + return nand_prog_page_op(chip, page, 0, tmp_buf,
> + mtd->writesize + mtd->oobsize);
> }
>
> static int gpmi_ecc_read_oob_raw(struct mtd_info *mtd, struct nand_chip *chip,
> int page)
> {
> - nand_read_page_op(chip, page, 0, NULL, 0);
> -
> return gpmi_ecc_read_page_raw(mtd, chip, NULL, 1, page);
> }
>
> static int gpmi_ecc_write_oob_raw(struct mtd_info *mtd, struct nand_chip *chip,
> int page)
> {
> - nand_prog_page_begin_op(chip, page, 0, NULL, 0);
> -
> return gpmi_ecc_write_page_raw(mtd, chip, NULL, 1, page);
> }
>
> @@ -1806,9 +1810,7 @@ static int mx23_write_transcription_stamp(struct
> gpmi_nand_data *this)
> /* Write the first page of the current stride. */
> dev_dbg(dev, "Writing an NCB fingerprint in page 0x%x\n", page);
>
> - nand_prog_page_begin_op(chip, page, 0, NULL, 0);
> - chip->ecc.write_page_raw(mtd, chip, buffer, 0, page);
> - status = nand_prog_page_end_op(chip);
> + status = chip->ecc.write_page_raw(mtd, chip, buffer, 0, page);
> if (status)
> dev_err(dev, "[%s] Write failed.\n", __func__);
> }
<snip>
> diff --git a/drivers/mtd/nand/vf610_nfc.c b/drivers/mtd/nand/vf610_nfc.c
> index 8037d4b48a05..80d31a58e558 100644
> --- a/drivers/mtd/nand/vf610_nfc.c
> +++ b/drivers/mtd/nand/vf610_nfc.c
> @@ -560,7 +560,7 @@ static int vf610_nfc_read_page(struct mtd_info
> *mtd, struct nand_chip *chip,
> int eccsize = chip->ecc.size;
> int stat;
>
> - vf610_nfc_read_buf(mtd, buf, eccsize);
> + nand_read_page_op(chip, page, 0, buf, eccsize);
> if (oob_required)
> vf610_nfc_read_buf(mtd, chip->oob_poi, mtd->oobsize);
>
> @@ -580,7 +580,7 @@ static int vf610_nfc_write_page(struct mtd_info
> *mtd, struct nand_chip *chip,
> {
> struct vf610_nfc *nfc = mtd_to_nfc(mtd);
>
> - vf610_nfc_write_buf(mtd, buf, mtd->writesize);
We currently ignore NAND_CMD_SEQIN in ->cmdfunc anyway, so I think this
change would not even be necessary here.
This is a NAND controller which will benefit from the new interface. I
plan to convert the driver to the new interface, maybe I manage to do
that soon so we have a second driver making use of the new interface.
> + nand_prog_page_begin_op(chip, page, 0, buf, mtd->writesize);
> if (oob_required)
> vf610_nfc_write_buf(mtd, chip->oob_poi, mtd->oobsize);
>
> @@ -588,7 +588,7 @@ static int vf610_nfc_write_page(struct mtd_info
> *mtd, struct nand_chip *chip,
> nfc->use_hw_ecc = true;
> nfc->write_sz = mtd->writesize + mtd->oobsize;
>
> - return 0;
> + return nand_prog_page_end_op(chip);
> }
>
> static const struct of_device_id vf610_nfc_dt_ids[] = {
--
Stefan
More information about the Linux-mediatek
mailing list