[PATCH v3 9/9] arm: dts: mt7623: add dts file for Bananapi R2 (BPI-R2) board
sean.wang at mediatek.com
sean.wang at mediatek.com
Fri May 12 00:56:46 PDT 2017
From: Sean Wang <sean.wang at mediatek.com>
Add support for the Bananapi R2 (BPI-R2) development board from
BIPAI KEJI. Detailed hardware information for BPI-R2 which could be
found on http://www.banana-pi.org/r2.html
The patch currently only adds Mediatek GMAC, MT7530 Switch, the crypto
engine, USB, IR, I2S, I2C, UART, SPI, PWM, GPIO keys, GPIO LEDs and
PMIC LEDs. As to the other missing hardware and peripherals, they would
be added and integrated continuously.
Signed-off-by: Sean Wang <sean.wang at mediatek.com>
---
Documentation/devicetree/bindings/arm/mediatek.txt | 2 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts | 478 +++++++++++++++++++++
3 files changed, 481 insertions(+)
create mode 100644 arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
diff --git a/Documentation/devicetree/bindings/arm/mediatek.txt b/Documentation/devicetree/bindings/arm/mediatek.txt
index 412c6bd..7b289bd 100644
--- a/Documentation/devicetree/bindings/arm/mediatek.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek.txt
@@ -42,6 +42,8 @@ Supported boards:
- Reference board for MT7623n with NAND:
Required root node properties:
- compatible = "mediatek,mt7623n-rfb-nand", "mediatek,mt7623";
+- Bananapi BPI-R2 board:
+ - compatible = "bananapi,bpi-r2", "mediatek,mt7623";
- MTK mt8127 tablet moose EVB:
Required root node properties:
- compatible = "mediatek,mt8127-moose", "mediatek,mt8127";
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 20a7c9d..34eb03f 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1035,6 +1035,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
mt6589-aquaris5.dtb \
mt6592-evb.dtb \
mt7623n-rfb-nand.dtb \
+ mt7623n-bananapi-bpi-r2.dtb \
mt8127-moose.dtb \
mt8135-evbp1.dtb
dtb-$(CONFIG_ARCH_ZX) += zx296702-ad1.dtb
diff --git a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
new file mode 100644
index 0000000..cb1bd20
--- /dev/null
+++ b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
@@ -0,0 +1,478 @@
+/*
+ * Copyright 2017 Sean Wang <sean.wang at mediatek.com>
+ *
+ * Sean Wang <sean.wang at mediatek.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include "mt7623-mt6323.dtsi"
+
+/ {
+ model = "Bananapi BPI-R2";
+ compatible = "bananapi,bpi-r2", "mediatek,mt7623";
+
+ aliases {
+ serial2 = &uart2;
+ };
+
+ chosen {
+ stdout-path = "serial2:115200n8";
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&key_pins_a>;
+
+ factory {
+ label = "factory";
+ linux,code = <BTN_0>;
+ gpios = <&pio 256 GPIO_ACTIVE_LOW>;
+ };
+
+ wps {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&pio 257 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_a>;
+
+ red {
+ label = "bpi-r2:pio:red";
+ gpios = <&pio 239 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ green {
+ label = "bpi-r2:pio:green";
+ gpios = <&pio 240 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ blue {
+ label = "bpi-r2:pio:blue";
+ gpios = <&pio 241 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+
+ memory at 80000000 {
+ reg = <0 0x80000000 0 0x40000000>;
+ };
+
+ sound:sound {
+ compatible = "mediatek,mt2701-wm8960-machine";
+ mediatek,platform = <&afe>;
+ audio-routing =
+ "Headphone", "HP_L",
+ "Headphone", "HP_R",
+ "LINPUT1", "AMIC",
+ "RINPUT1", "AMIC";
+ mediatek,audio-codec = <&wm8960>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s0_pins_a>;
+ };
+};
+
+&pio {
+ cir_pins_a:cir at 0 {
+ pins_cir {
+ pinmux = <MT7623_PIN_46_IR_FUNC_IR>;
+ bias-disable;
+ };
+ };
+
+ i2c0_pins_a: i2c at 0 {
+ pins_i2c0 {
+ pinmux = <MT7623_PIN_75_SDA0_FUNC_SDA0>,
+ <MT7623_PIN_76_SCL0_FUNC_SCL0>;
+ bias-disable;
+ };
+ };
+
+ i2c1_pins_a: i2c at 1 {
+ pin_i2c1 {
+ pinmux = <MT7623_PIN_57_SDA1_FUNC_SDA1>,
+ <MT7623_PIN_58_SCL1_FUNC_SCL1>;
+ bias-disable;
+ };
+ };
+
+ i2s0_pins_a: i2s at 0 {
+ pin_i2s0 {
+ pinmux = <MT7623_PIN_49_I2S0_DATA_FUNC_I2S0_DATA>,
+ <MT7623_PIN_72_I2S0_DATA_IN_FUNC_I2S0_DATA_IN>,
+ <MT7623_PIN_73_I2S0_LRCK_FUNC_I2S0_LRCK>,
+ <MT7623_PIN_74_I2S0_BCK_FUNC_I2S0_BCK>,
+ <MT7623_PIN_126_I2S0_MCLK_FUNC_I2S0_MCLK>;
+ drive-strength = <MTK_DRIVE_12mA>;
+ bias-pull-down;
+ };
+ };
+
+ i2s1_pins_a: i2s at 1 {
+ pin_i2s1 {
+ pinmux = <MT7623_PIN_33_I2S1_DATA_FUNC_I2S1_DATA>,
+ <MT7623_PIN_34_I2S1_DATA_IN_FUNC_I2S1_DATA_IN>,
+ <MT7623_PIN_35_I2S1_BCK_FUNC_I2S1_BCK>,
+ <MT7623_PIN_36_I2S1_LRCK_FUNC_I2S1_LRCK>,
+ <MT7623_PIN_37_I2S1_MCLK_FUNC_I2S1_MCLK>;
+ drive-strength = <MTK_DRIVE_12mA>;
+ bias-pull-down;
+ };
+ };
+
+ key_pins_a: keys at 0 {
+ pins_keys {
+ pinmux = <MT7623_PIN_256_GPIO256_FUNC_GPIO256>,
+ <MT7623_PIN_257_GPIO257_FUNC_GPIO257> ;
+ input-enable;
+ };
+ };
+
+ led_pins_a: leds at 0 {
+ pins_leds {
+ pinmux = <MT7623_PIN_239_EXT_SDIO0_FUNC_GPIO239>,
+ <MT7623_PIN_240_EXT_XCS_FUNC_GPIO240>,
+ <MT7623_PIN_241_EXT_SCK_FUNC_GPIO241>;
+ };
+ };
+
+ mmc0_pins_default: mmc0default {
+ pins_cmd_dat {
+ pinmux = <MT7623_PIN_111_MSDC0_DAT7_FUNC_MSDC0_DAT7>,
+ <MT7623_PIN_112_MSDC0_DAT6_FUNC_MSDC0_DAT6>,
+ <MT7623_PIN_113_MSDC0_DAT5_FUNC_MSDC0_DAT5>,
+ <MT7623_PIN_114_MSDC0_DAT4_FUNC_MSDC0_DAT4>,
+ <MT7623_PIN_118_MSDC0_DAT3_FUNC_MSDC0_DAT3>,
+ <MT7623_PIN_119_MSDC0_DAT2_FUNC_MSDC0_DAT2>,
+ <MT7623_PIN_120_MSDC0_DAT1_FUNC_MSDC0_DAT1>,
+ <MT7623_PIN_121_MSDC0_DAT0_FUNC_MSDC0_DAT0>,
+ <MT7623_PIN_116_MSDC0_CMD_FUNC_MSDC0_CMD>;
+ input-enable;
+ bias-pull-up;
+ };
+
+ pins_clk {
+ pinmux = <MT7623_PIN_117_MSDC0_CLK_FUNC_MSDC0_CLK>;
+ bias-pull-down;
+ };
+
+ pins_rst {
+ pinmux = <MT7623_PIN_115_MSDC0_RSTB_FUNC_MSDC0_RSTB>;
+ bias-pull-up;
+ };
+ };
+
+ mmc0_pins_uhs: mmc0 {
+ pins_cmd_dat {
+ pinmux = <MT7623_PIN_111_MSDC0_DAT7_FUNC_MSDC0_DAT7>,
+ <MT7623_PIN_112_MSDC0_DAT6_FUNC_MSDC0_DAT6>,
+ <MT7623_PIN_113_MSDC0_DAT5_FUNC_MSDC0_DAT5>,
+ <MT7623_PIN_114_MSDC0_DAT4_FUNC_MSDC0_DAT4>,
+ <MT7623_PIN_118_MSDC0_DAT3_FUNC_MSDC0_DAT3>,
+ <MT7623_PIN_119_MSDC0_DAT2_FUNC_MSDC0_DAT2>,
+ <MT7623_PIN_120_MSDC0_DAT1_FUNC_MSDC0_DAT1>,
+ <MT7623_PIN_121_MSDC0_DAT0_FUNC_MSDC0_DAT0>,
+ <MT7623_PIN_116_MSDC0_CMD_FUNC_MSDC0_CMD>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_2mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+
+ pins_clk {
+ pinmux = <MT7623_PIN_117_MSDC0_CLK_FUNC_MSDC0_CLK>;
+ drive-strength = <MTK_DRIVE_2mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_01>;
+ };
+
+ pins_rst {
+ pinmux = <MT7623_PIN_115_MSDC0_RSTB_FUNC_MSDC0_RSTB>;
+ bias-pull-up;
+ };
+ };
+
+ mmc1_pins_default: mmc1default {
+ pins_cmd_dat {
+ pinmux = <MT7623_PIN_107_MSDC1_DAT0_FUNC_MSDC1_DAT0>,
+ <MT7623_PIN_108_MSDC1_DAT1_FUNC_MSDC1_DAT1>,
+ <MT7623_PIN_109_MSDC1_DAT2_FUNC_MSDC1_DAT2>,
+ <MT7623_PIN_110_MSDC1_DAT3_FUNC_MSDC1_DAT3>,
+ <MT7623_PIN_105_MSDC1_CMD_FUNC_MSDC1_CMD>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_4mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins_clk {
+ pinmux = <MT7623_PIN_106_MSDC1_CLK_FUNC_MSDC1_CLK>;
+ bias-pull-down;
+ drive-strength = <MTK_DRIVE_4mA>;
+ };
+ };
+
+ mmc1_pins_uhs: mmc1 {
+ pins_cmd_dat {
+ pinmux = <MT7623_PIN_107_MSDC1_DAT0_FUNC_MSDC1_DAT0>,
+ <MT7623_PIN_108_MSDC1_DAT1_FUNC_MSDC1_DAT1>,
+ <MT7623_PIN_109_MSDC1_DAT2_FUNC_MSDC1_DAT2>,
+ <MT7623_PIN_110_MSDC1_DAT3_FUNC_MSDC1_DAT3>,
+ <MT7623_PIN_105_MSDC1_CMD_FUNC_MSDC1_CMD>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_4mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins_clk {
+ pinmux = <MT7623_PIN_106_MSDC1_CLK_FUNC_MSDC1_CLK>;
+ drive-strength = <MTK_DRIVE_4mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+ };
+
+ spi0_pins_a: spi at 0 {
+ pins_spi {
+ pinmux = <MT7623_PIN_53_SPI0_CSN_FUNC_SPI0_CS>,
+ <MT7623_PIN_54_SPI0_CK_FUNC_SPI0_CK>,
+ <MT7623_PIN_55_SPI0_MI_FUNC_SPI0_MI>,
+ <MT7623_PIN_56_SPI0_MO_FUNC_SPI0_MO>;
+ bias-disable;
+ };
+ };
+
+ pwm_pins_a: pwm at 0 {
+ pins_pwm {
+ pinmux = <MT7623_PIN_203_PWM0_FUNC_PWM0>,
+ <MT7623_PIN_204_PWM1_FUNC_PWM1>,
+ <MT7623_PIN_205_PWM2_FUNC_PWM2>,
+ <MT7623_PIN_206_PWM3_FUNC_PWM3>,
+ <MT7623_PIN_207_PWM4_FUNC_PWM4>;
+ };
+ };
+
+ uart0_pins_a: uart at 0 {
+ pins_dat {
+ pinmux = <MT7623_PIN_79_URXD0_FUNC_URXD0>,
+ <MT7623_PIN_80_UTXD0_FUNC_UTXD0>;
+ };
+ };
+
+ uart1_pins_a: uart at 1 {
+ pins_dat {
+ pinmux = <MT7623_PIN_81_URXD1_FUNC_URXD1>,
+ <MT7623_PIN_82_UTXD1_FUNC_UTXD1>;
+ };
+ };
+};
+
+&cir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cir_pins_a>;
+ status = "okay";
+};
+
+&crypto {
+ status = "okay";
+};
+
+ð {
+ status = "okay";
+ gmac0: mac at 0 {
+ compatible = "mediatek,eth-mac";
+ reg = <0>;
+ phy-mode = "trgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+ };
+
+ mdio: mdio-bus {
+ switch at 0 {
+ compatible = "mediatek,mt7530";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ pinctrl-names = "default";
+ reset-gpios = <&pio 33 0>;
+ core-supply = <&mt6323_vpa_reg>;
+ io-supply = <&mt6323_vemc3v3_reg>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+ port at 0 {
+ reg = <0>;
+ label = "lan0";
+ };
+
+ port at 1 {
+ reg = <1>;
+ label = "lan1";
+ };
+
+ port at 2 {
+ reg = <2>;
+ label = "lan2";
+ };
+
+ port at 3 {
+ reg = <3>;
+ label = "lan3";
+ };
+
+ port at 4 {
+ reg = <4>;
+ label = "wan";
+ };
+
+ port at 6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+ };
+};
+
+&pwrap {
+ mt6323 {
+ mt6323led: led {
+ compatible = "mediatek,mt6323-led";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led at 0 {
+ reg = <0>;
+ label = "bpi-r2:isink:green";
+ default-state = "off";
+ };
+ led at 1 {
+ reg = <1>;
+ label = "bpi-r2:isink:red";
+ default-state = "off";
+ };
+ led at 2 {
+ reg = <2>;
+ label = "bpi-r2:isink:blue";
+ default-state = "off";
+ };
+ };
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+
+ wm8960: wm8960 at 1a {
+ compatible = "wlf,wm8960";
+ reg = <0x1a>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm_pins_a>;
+ status = "okay";
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins_a>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "disabled";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins_a>;
+ status = "disabled";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&u3phy1 {
+ status = "okay";
+};
+
+&u3phy2 {
+ status = "okay";
+};
+
+&usb1 {
+ vusb33-supply = <&mt6323_vusb_reg>;
+ status = "okay";
+};
+
+&usb2 {
+ vusb33-supply = <&mt6323_vusb_reg>;
+ status = "okay";
+};
--
2.7.4
More information about the Linux-mediatek
mailing list