[PATCH v3 2/2] dt-bindings: pcie: Add documentation for Mediatek PCIe
Matthias Brugger
matthias.bgg at gmail.com
Wed May 10 00:58:47 PDT 2017
On 10/05/17 04:07, Ryder Lee wrote:
> Add documentation for PCIe host driver available in MT7623
> series SoCs.
>
> Signed-off-by: Ryder Lee <ryder.lee at mediatek.com>
> Acked-by: Rob Herring <robh at kernel.org>
> ---
> .../bindings/pci/mediatek,mt7623-pcie.txt | 149 +++++++++++++++++++++
> 1 file changed, 149 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pci/mediatek,mt7623-pcie.txt
>
> diff --git a/Documentation/devicetree/bindings/pci/mediatek,mt7623-pcie.txt b/Documentation/devicetree/bindings/pci/mediatek,mt7623-pcie.txt
> new file mode 100644
> index 0000000..a9393ce
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pci/mediatek,mt7623-pcie.txt
> @@ -0,0 +1,149 @@
> +Mediatek Gen2 PCIe controller which is available on MT7623 series SoCs
> +
> +PCIe subsys supports single root complex (RC) with 3 Root Ports. Each root
> +ports supports a Gen2 1-lane Link and has PIPE interface to PHY.
> +
> +Required properties:
> +- compatible: Should contain "mediatek,mt7623-pcie".
> +- device_type: Must be "pci"
> +- reg: Base addresses and lengths of the PCIe controller.
> +- #address-cells: Address representation for root ports (must be 3)
> +- #size-cells: Size representation for root ports (must be 2)
> +- #interrupt-cells: Size representation for interrupts (must be 1)
> +- interrupts: Three interrupt outputs of the controller. Must contain an
> + entry for each entry in the interrupt-names property.
> +- interrupt-names: Must include the following names
> + - "pcie-int0"
> + - "pcie-int1"
> + - "pcie-int2"
> +- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties
> + Please refer to the standard PCI bus binding document for a more detailed
> + explanation.
> +- clocks: Must contain an entry for each entry in clock-names.
> + See ../clocks/clock-bindings.txt for details.
> +- clock-names: Must include the following entries:
> + - free_ck :for reference clock of PCIe subsys
> + - sys_ck0 :for clock of Port0
> + - sys_ck1 :for clock of Port1
> + - sys_ck2 :for clock of Port2
> +- resets: Must contain an entry for each entry in reset-names.
> + See ../reset/reset.txt for details.
> +- reset-names: Must include the following entries:
> + - pcie-rst0 :port0 reset
> + - pcie-rst1 :port1 reset
> + - pcie-rst2 :port2 reset
> +- phys: list of PHY specifiers (used by generic PHY framework).
> +- phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the
> + number of PHYs as specified in *phys* property.
> +- power-domains: A phandle and power domain specifier pair to the power domain
> + which is responsible for collapsing and restoring power to the peripheral.
> +- bus-range: Range of bus numbers associated with this controller.
> +- ranges:
> + - The first three entries are expected to translate the addresses for the root
> + port registers, which are referenced by the assigned-addresses property of
> + the root port nodes (see below).
> + - The remaining entries setup the mapping for the standard I/O and memory
> + regions.
> + Please refer to the standard PCI bus binding document for a more detailed
> + explanation.
> +
> +In addition, the device tree node must have sub-nodes describing each
> +PCIe port interface, having the following mandatory properties:
> +
> +Required properties:
> +- device_type: Must be "pci"
> +- assigned-addresses: Address and size of the port configuration registers
> +- reg: Only the first four bytes are used to refer to the correct bus number
> + and device number.
> +- #address-cells: Must be 3
> +- #size-cells: Must be 2
> +- #interrupt-cells: Must be 1
> +- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties
> + Please refer to the standard PCI bus binding document for a more detailed
> + explanation.
> +- ranges: Sub-ranges distributed from the PCIe controller node. An empty
> + property is sufficient.
> +- num-lanes: Number of lanes to use for this port.
> +
> +Examples:
> +
> + hifsys: syscon at 1a000000 {
> + compatible = "mediatek,mt7623-hifsys", "syscon";
If you want to put the clock controller subsystem node to the example,
please use a valid compatible, for example:
compatible = "mediatek,mt7623-hifsys",
"mediatek,mt2701-hifsys",
"syscon";
Thanks,
Matthias
> + reg = <0 0x1a000000 0 0x1000>;
> + #clock-cells = <1>;
> + #reset-cells = <1>;
> + };
> +
> + pcie: pcie-controller at 1a140000 {
> + compatible = "mediatek,mt7623-pcie";
> + device_type = "pci";
> + reg = <0 0x1a140000 0 0x1000>; /* PCIe shared registers */
> + #address-cells = <3>;
> + #size-cells = <2>;
> + #interrupt-cells = <1>;
> + interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>,
> + <GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>;
> + interrupt-names = "pcie-int0", "pcie-int1", "pcie-int2";
> + interrupt-map-mask = <0xf800 0 0 0>;
> + interrupt-map = <0x0000 0 0 0 &gic GIC_SPI 193 IRQ_TYPE_NONE>,
> + <0x0800 0 0 0 &gic GIC_SPI 194 IRQ_TYPE_NONE>,
> + <0x1000 0 0 0 &gic GIC_SPI 195 IRQ_TYPE_NONE>;
> + clocks = <&topckgen CLK_TOP_ETHIF_SEL>,
> + <&hifsys CLK_HIFSYS_PCIE0>,
> + <&hifsys CLK_HIFSYS_PCIE1>,
> + <&hifsys CLK_HIFSYS_PCIE2>;
> + clock-names = "free_ck", "sys_ck0", "sys_ck1", "sys_ck2";
> + resets = <&hifsys MT2701_HIFSYS_PCIE0_RST>,
> + <&hifsys MT2701_HIFSYS_PCIE1_RST>,
> + <&hifsys MT2701_HIFSYS_PCIE2_RST>;
> + reset-names = "pcie-rst0", "pcie-rst1", "pcie-rst2";
> + phys = <&pcie0_phy>, <&pcie1_phy>, <&pcie2_phy>;
> + phy-names = "pcie-phy0", "pcie-phy1", "pcie-phy2";
> + power-domains = <&scpsys MT2701_POWER_DOMAIN_HIF>;
> + bus-range = <0x00 0xff>;
> + ranges = <0x82000000 0 0x1a142000 0 0x1a142000 0 0x1000 /* Port0 registers */
> + 0x82000000 0 0x1a143000 0 0x1a143000 0 0x1000 /* Port1 registers */
> + 0x82000000 0 0x1a144000 0 0x1a144000 0 0x1000 /* Port2 registers */
> + 0x81000000 0 0x1a160000 0 0x1a160000 0 0x00010000 /* I/O space */
> + 0x83000000 0 0x60000000 0 0x60000000 0 0x10000000>; /* memory space */
> +
> + pcie at 0,0 {
> + device_type = "pci";
> + assigned-addresses = <0x82000000 0 0x1a142000 0 0x1000>;
> + reg = <0x0000 0 0 0 0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0>;
> + interrupt-map = <0 0 0 0 &gic GIC_SPI 193 IRQ_TYPE_NONE>;
> + ranges;
> + num-lanes = <1>;
> + };
> +
> + pcie at 1,0 {
> + device_type = "pci";
> + assigned-addresses = <0x82000800 0 0x1a143000 0 0x1000>;
> + reg = <0x0800 0 0 0 0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0>;
> + interrupt-map = <0 0 0 0 &gic GIC_SPI 194 IRQ_TYPE_NONE>;
> + ranges;
> + num-lanes = <1>;
> + };
> +
> + pcie at 2,0 {
> + device_type = "pci";
> + assigned-addresses = <0x82001000 0 0x1a144000 0 0x1000>;
> + reg = <0x1000 0 0 0 0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0>;
> + interrupt-map = <0 0 0 0 &gic GIC_SPI 195 IRQ_TYPE_NONE>;
> + ranges;
> + num-lanes = <1>;
> + };
> + };
>
More information about the Linux-mediatek
mailing list