[PATCH v4 2/2] arm64: dts: Add Mediatek SoC MT2712 and evaluation board dts and Makefile

YT Shen yt.shen at mediatek.com
Thu Jul 20 23:32:26 PDT 2017


On Wed, 2017-07-19 at 11:26 +0200, Matthias Brugger wrote:
> 
> On 07/19/2017 08:48 AM, YT Shen wrote:
> > On Tue, 2017-07-18 at 18:29 +0200, Matthias Brugger wrote:
> >>
> >> On 06/22/2017 11:32 AM, YT Shen wrote:
> >>> This adds basic chip support for Mediatek 2712
> 
> [...]
> 
> >>> +
> >>> +	uart_clk: dummy26m {
> >>> +		compatible = "fixed-clock";
> >>> +		clock-frequency = <26000000>;
> >>> +		#clock-cells = <0>;
> >>> +	};
> >>> +
> 
> [...]
> 
> >>> +
> >>> +	soc {
> >>> +		#address-cells = <2>;
> >>> +		#size-cells = <2>;
> >>> +		compatible = "simple-bus";
> >>> +		ranges;
> >>> +
> >>> +		uart5: serial at 1000f000 {
> >>> +			compatible = "mediatek,mt2712-uart",
> >>> +				     "mediatek,mt6577-uart";
> >>> +			reg = <0 0x1000f000 0 0x400>;
> >>> +			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_LOW>;
> >>> +			clocks = <&uart_clk>, <&uart_clk>;
> >>> +			clock-names = "baud", "bus";
> >>> +			status = "disabled";
> >>> +		};
> >>
> >> So baud and bus clock are both 26 MHz?
> > We didn't have CCF clock support in this series.
> > After we have clock source support, we could use the correct clocks to
> > the UARTs and drop the 26MHz fixed rate UART clock.
> > 
> > The bus clock is 26MHz.  The baud clock could be from another clock
> > source, using the same 26MHz fixed clock works also.
> > 
> > 
> > [1] https://patchwork.kernel.org/patch/9670877/
> > [2] https://patchwork.kernel.org/patch/6436021/
> > 
> 
> Yes, just using one 26 MHz clock works, but it uses an deprecated 
> binding, so we should not do this, as through copying from the source of 
> other SoCs we will keep it alive forever. Anyway that's not your case, 
> as you defined the two clocks.
> 
> The device tree should reflect the HW, that's why I asked for the clock 
> frequency of both clocks. I searched the git history and it was never 
> done right before. So you could be the first :)
> 
> Thanks,
> Matthias
Ok, I want to make it clear.  The following example

        baud_clk: dummy26m {
                compatible = "fixed-clock";
                clock-frequency = <26000000>;
                #clock-cells = <0>;
        };

        sys_clk: dummyclk {
                compatible = "fixed-clock";
                clock-frequency = <26000000>;
                #clock-cells = <0>;
        };

	uart0: serial at 11002000 {
[...]
                clocks = <&baud_clk>, <&sys_clk>;
[...]
	}

Do you think it is clear to reflect the HW that the baud clock and sys
clock can be different source or we need to choose another frequency?
Thanks.

yt.shen





More information about the Linux-mediatek mailing list