[PATCH] spi: mediatek: Manually set dma_ops for spi_master device

Daniel Kurtz djkurtz at chromium.org
Thu Jan 26 08:52:15 PST 2017


On Fri, Jan 27, 2017 at 12:35 AM, Dmitry Torokhov <dtor at chromium.org> wrote:
> On Thu, Jan 26, 2017 at 8:29 AM, Daniel Kurtz <djkurtz at chromium.org> wrote:
>> Hi Robin,
>>
>> On Thu, Jan 26, 2017 at 1:59 AM, Robin Murphy <robin.murphy at arm.com> wrote:
>>>
>>> On 25/01/17 10:24, Daniel Kurtz wrote:
>>> > Hi Robin,
>>> >
>>> > On Tue, Jan 24, 2017 at 11:14 PM, Robin Murphy <robin.murphy at arm.com> wrote:
>>> >> Hi Dan,
>>> >
>>> > [snip...]
>>> >
>>> >>> And I really don't know why we needed to set the coherent_dma_mask to 0 to
>>> >>> avoid SPI transaction errors.
>>> >>
>>> >> Following what I mentioned above, "git grep dma_alloc drivers/spi" makes
>>> >> it seem like coherent DMA isn't used anywhere relevant, which is rather
>>> >> puzzling. Unless of course somewhere along the line somebody's done the
>>> >> dev->dma_mask = &dev->dma_coherent_mask hack, with the result that
>>> >> writing one mask hits both, making *all* DMA fail and big transfers fall
>>> >> back to PIO.
>>> >
>>> > You mean this last line?
>>> >
>>> >>> @@ -575,6 +576,10 @@ static int mtk_spi_probe(struct platform_device *pdev)
>>> >>>               goto err_put_master;
>>> >>>       }
>>> >>>
>>> >>> +     /* Call of_dma_configure to set up spi_master's dma_ops */
>>> >>> +     of_dma_configure(&master->dev, master->dev.of_node);
>>> >>> +     /* But explicitly set the coherent_dma_mask to 0 */
>>> >>> +     master->dev.coherent_dma_mask = 0;
>>> >>>       if (!pdev->dev.dma_mask)
>>> >>>               pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
>>> >                                   ^^^^^
>>>
>>> Ha, I totally failed to spot that!
>>>
>>> > As predicted, setting the dma_mask = 0 causes "all DMA to fail".  In
>>> > particular, dma_capable() always returns false, so
>>> > swiotlb_map_sg_attrs() takes the map_single() path, instead of just
>>> > assigning:
>>> >
>>> >    sg->dma_address = dev_addr;
>>> >
>>> > swiotlb_map_sg_attrs(struct device *hwdev, struct scatterlist *sgl, int nelems,
>>> >                      enum dma_data_direction dir, unsigned long attrs)
>>> > {
>>> >         struct scatterlist *sg;
>>> >         int i;
>>> >
>>> >         BUG_ON(dir == DMA_NONE);
>>> >
>>> >         for_each_sg(sgl, sg, nelems, i) {
>>> >                 phys_addr_t paddr = sg_phys(sg);
>>> >                 dma_addr_t dev_addr = phys_to_dma(hwdev, paddr);
>>> >
>>> >                 if (swiotlb_force == SWIOTLB_FORCE ||
>>> >                     !dma_capable(hwdev, dev_addr, sg->length)) {
>>> >                         phys_addr_t map = map_single(hwdev, sg_phys(sg),
>>> >                                                      sg->length, dir, attrs);
>>> >                         ...
>>> >                         }
>>> >                         sg->dma_address = phys_to_dma(hwdev, map);
>>> >                 } else
>>> >                         sg->dma_address = dev_addr;
>>> >                 sg_dma_len(sg) = sg->length;
>>> >         }
>>> >         return nelems;
>>> > }
>>> >
>>> > So, I think this means that the only reason the MTK SPI driver ever
>>> > worked before was that it was tested on an older kernel, so the
>>> > spi_master was defaulting to swiotlb_dma_ops with a 0 dma_mask, and
>>> > therefore it was using SWIOTLB bounce buffers (via 'map_single'), and
>>> > not actually ever doing real DMA.
>>>
>>> Well, it's still "real DMA" if the device is able to slurp data out of
>>> the bounce buffer. That suggests there might be some mismatch between
>>> the default DMA mask it's getting given and the actual hardware
>>> capability (i.e. the bounce buffer happens to fall somewhere accessible,
>>> but other addresses may not be) - is crazy 33-bit mode involved here?
>>
>> AFAICT, the Mediatek SPI does not have a 33-bit mode.  The Mediatek
>> SPI DMA registers are only 32-bits wide, so the default 0xffffffff
>> dma_mask is correct.  For larger addresses, swiotlb properly falls
>> back to using a bounce buffer.
>>
>> However, I did discover what the real problem was.  The Mediatek SPI
>> DMA does not like un-aligned addresses.
>
> Nobody doing DMA likes unaligned buffers. In fact, memory used for DMA
> must be cacheline aligned, or you going to have trouble. What
> component supplies unaligned buffers to SPI core for transfers?

cros-ec-spi

>
> Thanks,
> Dmitry



More information about the Linux-mediatek mailing list