[PATCH v4 1/4] Documentation: devicetree: Add document bindings for leds-mt6323

[Jacek Anaszewski]

Hi Sean,

Thanks for the update. I have one comment below.

On 02/24/2017 07:47 PM, sean.wang at mediatek.com wrote:
> From: Sean Wang <sean.wang at mediatek.com>
> 
> This patch adds documentation for devicetree bindings
> for LED support on MT6323 PMIC
> 
> Signed-off-by: Sean Wang <sean.wang at mediatek.com>
> ---
>  .../devicetree/bindings/leds/leds-mt6323.txt       | 64 ++++++++++++++++++++++
>  1 file changed, 64 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/leds/leds-mt6323.txt
> 
> diff --git a/Documentation/devicetree/bindings/leds/leds-mt6323.txt b/Documentation/devicetree/bindings/leds/leds-mt6323.txt
> new file mode 100644
> index 0000000..950b8c6
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/leds/leds-mt6323.txt
> @@ -0,0 +1,64 @@
> +Device Tree Bindings for LED support on MT6323 PMIC
> +
> +MT6323 LED controller is subfunction provided by
> +MT6323 PMIC, so the LED controllers are defined as
> +the subnode of the function node provided by MT6323
> +PMIC controller that is being defined as one kind of
> +Muti-Function Device (MFD) using shared bus called
> +PMIC wrapper for each subfunction to access remote
> +MT6323 PMIC hardware.
> +
> +For MT6323 MFD bindings see:
> +Documentation/devicetree/bindings/mfd/mt6397.txt
> +For MediaTek PMIC wrapper bindings see:
> +Documentation/devicetree/bindings/soc/mediatek/pwrap.txt
> +
> +There's sub-node for the LED controller that describes
> +the initial behavior for each LED physically and currently
> +only four LED sub-nodes can be supported.
> +
> +Required properties:
> +- compatible : Must be "mediatek,mt6323-led"
> +- reg : LED channel number (0..3)
> +
> +Optional properties:
> +- label : (optional)
> +  see Documentation/devicetree/bindings/leds/common.txt
> +- linux,default-trigger : (optional)
> +  see Documentation/devicetree/bindings/leds/common.txt
> +- default-state: (optional) The initial state of the LED
> +  see Documentation/devicetree/bindings/leds/common.txt
> +
> +Example:
> +
> +&pwrap {
> +	pmic: mt6323 {
> +		compatible = "mediatek,mt6323";
> +		interrupt-parent = <&pio>;
> +		interrupts = <150 IRQ_TYPE_LEVEL_HIGH>;
> +		interrupt-controller;
> +		#interrupt-cells = <2>;
> +
> +		mt6323led: mt6323led{
> +			compatible = "mediatek,mt6323-led";

You require here also:

#address-cells = <1>;
#size-cells = <0>;

Without these entries you should notice a warning from dtc compiler.


> +
> +			led0: isink0 {
> +				reg = <0>;
> +				label = "LED0"
> +				linux,default-trigger = "timer";
> +				default-state = "on";
> +			};
> +			led1: isink1 {
> +				reg = <1>;
> +				label = "LED1";
> +				default-state = "on";
> +			};
> +			led2: isink2 {
> +				reg = <2>;
> +				label = "LED2";
> +				linux,default-trigger = "timer";
> +				default-state = "off";
> +			};
> +		};
> +	};
> +};
> 

-- 
Best regards,
Jacek Anaszewski