[PATCH] MIPS: dts: ralink: Add Mediatek MT7628A SoC

[Harvey Hunt]

Hi Rob,

Thanks for the review.

On 17/08/17 22:34, Rob Herring wrote:
> On Tue, Aug 15, 2017 at 05:28:50PM +0100, Harvey Hunt wrote:
>> The MT7628A is the successor to the MT7620 and pin compatible with the
>> MT7688A, although the latter supports only a 1T1R antenna rather than
>> a 2T2R antenna.
>>
>> This commit adds support for the following features:
>>
>> - UART
>> - USB PHY
>> - EHCI
>> - Interrupt controller
>> - System controller
>> - Memory controller
>> - Reset controller
>>
>> Signed-off-by: Harvey Hunt <harvey.hunt at imgtec.com>
>> Cc: John Crispin <john at phrozen.org>
>> Cc: linux-mips at linux-mips.org
>> Cc: devicetree at vger.kernel.org
>> Cc: linux-kernel at vger.kernel.org
>> Cc: linux-mediatek at lists.infradead.org
>> ---
>>   Documentation/devicetree/bindings/mips/ralink.txt |   1 +
>>   arch/mips/boot/dts/ralink/mt7628a.dtsi            | 125 ++++++++++++++++++++++
>>   2 files changed, 126 insertions(+)
>>   create mode 100644 arch/mips/boot/dts/ralink/mt7628a.dtsi
>>
>> diff --git a/Documentation/devicetree/bindings/mips/ralink.txt b/Documentation/devicetree/bindings/mips/ralink.txt
>> index b35a8d0..a16e8d7 100644
>> --- a/Documentation/devicetree/bindings/mips/ralink.txt
>> +++ b/Documentation/devicetree/bindings/mips/ralink.txt
>> @@ -15,3 +15,4 @@ value must be one of the following values:
>>     ralink,rt5350-soc
>>     ralink,mt7620a-soc
>>     ralink,mt7620n-soc
>> +  ralink,mt7628a-soc
>> diff --git a/arch/mips/boot/dts/ralink/mt7628a.dtsi b/arch/mips/boot/dts/ralink/mt7628a.dtsi
>> new file mode 100644
>> index 0000000..8461fe9
>> --- /dev/null
>> +++ b/arch/mips/boot/dts/ralink/mt7628a.dtsi
>> @@ -0,0 +1,125 @@
>> +/ {
>> +	#address-cells = <1>;
>> +	#size-cells = <1>;
>> +	compatible = "ralink,mt7628a-soc";
>> +
>> +	cpus {
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		cpu at 0 {
>> +			compatible = "mti,mips24KEc";
>> +			device_type = "cpu";
>> +			reg = <0>;
>> +		};
>> +	};
>> +
>> +	resetctrl: resetctrl {
> 
> reset-controller {

Done

> 
>> +		compatible = "ralink,rt2880-reset";
>> +		#reset-cells = <1>;
>> +	};
>> +
>> +	cpuintc: cpuintc {
> 
> interrupt-controller {

Done

> 
>> +		#address-cells = <0>;
>> +		#interrupt-cells = <1>;
>> +		interrupt-controller;
>> +		compatible = "mti,cpu-interrupt-controller";
>> +	};
>> +
>> +	palmbus at 10000000 {
>> +		compatible = "palmbus";
>> +		reg = <0x10000000 0x200000>;
>> +		ranges = <0x0 0x10000000 0x1FFFFF>;
>> +
>> +		#address-cells = <1>;
>> +		#size-cells = <1>;
>> +
>> +		sysc at 0 {
> 
> system-controller at 0

Done

> 
>> +			compatible = "ralink,mt7620a-sysc";
>> +			reg = <0x0 0x100>;
>> +		};
>> +
>> +		intc: intc at 200 {
> 
> interrupt-controller at 200

Done

> 
>> +			compatible = "ralink,rt2880-intc";
>> +			reg = <0x200 0x100>;
>> +
>> +			interrupt-controller;
>> +			#interrupt-cells = <1>;
>> +
>> +			resets = <&resetctrl 9>;
>> +			reset-names = "intc";
>> +
>> +			interrupt-parent = <&cpuintc>;
>> +			interrupts = <2>;
>> +
>> +			ralink,intc-registers = <0x9c 0xa0
>> +						 0x6c 0xa4
>> +						 0x80 0x78>;
>> +		};
>> +
>> +		memc at 300 {
> 
> memory-controller at 300

Done

> 
>> +			compatible = "ralink,mt7620a-memc";
>> +			reg = <0x300 0x100>;
>> +		};
>> +
>> +		uartlite at c00 {
> 
> serial at c00
> 
> And so on. IOW, use standard, generic node names as defined in the DT
> spec.


The clocks for the UARTs are using the device names "uartlite", "uart1" 
and "uart2" (as defined in arch/mips/ralink/mt7620.c).

Changing the name of the DT nodes causes the serial driver to bail as it 
can't find the clock for the device.

arch/mips/boot/dts/ralink/mt7620a.dtsi is already using the uartlite 
name, although it hasn't been documented...

Thanks,

Harvey

> 
>> +			compatible = "ns16550a";
>> +			reg = <0xc00 0x100>;
>> +
>> +			resets = <&resetctrl 12>;
>> +			reset-names = "uart0";
>> +
>> +			interrupt-parent = <&intc>;
>> +			interrupts = <20>;
>> +
>> +			reg-shift = <2>;
>> +		};
>> +
>> +		uart1 at d00 {
>> +			compatible = "ns16550a";
>> +			reg = <0xd00 0x100>;
>> +
>> +			resets = <&resetctrl 19>;
>> +			reset-names = "uart1";
>> +
>> +			interrupt-parent = <&intc>;
>> +			interrupts = <21>;
>> +
>> +			reg-shift = <2>;
>> +		};
>> +
>> +		uart2 at e00 {
>> +			compatible = "ns16550a";
>> +			reg = <0xe00 0x100>;
>> +
>> +			resets = <&resetctrl 20>;
>> +			reset-names = "uart2";
>> +
>> +			interrupt-parent = <&intc>;
>> +			interrupts = <22>;
>> +
>> +			reg-shift = <2>;
>> +		};
>> +	};
>> +
>> +	usbphy: uphy at 10120000 {
>> +		compatible = "mediatek,mt7628-usbphy";
>> +		reg = <0x10120000 0x1000>;
>> +
>> +		#phy-cells = <0>;
>> +
>> +		resets = <&resetctrl 22 &resetctrl 25>;
>> +		reset-names = "host", "device";
>> +	};
>> +
>> +	ehci at 101c0000 {
>> +		compatible = "generic-ehci";
>> +		reg = <0x101c0000 0x1000>;
>> +
>> +		phys = <&usbphy>;
>> +		phy-names = "usb";
>> +
>> +		interrupt-parent = <&intc>;
>> +		interrupts = <18>;
>> +	};
>> +};
>> -- 
>> 2.7.4
>>